Trinitron Color TV
Operating Instructions
KV-27S25
KV-27S35
KV-27V25
KV-2 7V3 5
KV-29RS25
KV-29RS25C
KV-29V35C
KV-29V65M
KV-29V75M
KV-32S25
KV-32S35
KV-32 TW25
KV-32 V25
KV-32 V35
KV-34V35C
KV-35V35
KV-35V45
KV-35V75
_1996 by Sony Corporation
To prevent fire or shock hazard, do not
expose the television to rain or
moisture.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
A'I-rENTION
RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RIESGO DE CHOQUE ELECTRICO
NO ABRIR
CAUTION : Iu _/LUUL, L ittL tiL_F, Ut LLL:L;I HIC bROOK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
I lu_, >) mbol is intcllded to alert the u_cl to the
presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
To prevent electric shoe k, do not use thib polarized AC plug with
an extension cord, receptacle or other outlet unless the blades can
be fully inserted to prevent blade exposure.
Precautions
Safety
• Operate the TV only on 120 V AC (except KV-29RS25C/
29V35C/34 V35C).
• Operate the TV only on 220 V AC (KV-29RS25C/29V35C/
34V35C only).
• One blade of the plug is wider than the other for safety
purposes and will fit into the power outlet only one way. If
you are unable to insert the plug fully into the outlet, contact
your dealer (except KV-29RS25C/29V35C/34V35C).
• Should any liquid or solid object fall into the cabinet, unplug
the TV and have it checked by qualified personnel before
operating it any further.
2
• Unplug ti_c l V trom the \vdll uutlet it you ,u e not going t_
use it for several days or more. To disconnect the cord, pull it
out by the plug. Never pull the cord itself.
For details concerning safety precautions, see the supplied leaflet
"IMPORTANT SAFEGUARDS."
Installing
• To prevent internal heat build-up, do not block the
ventilation openings.
• Do not install the TV in a hot or humid place, or in a place
subject to excessive dust or mechanical vibration.
CAUTION
When using TV games, computers, and similar products with
your TV, keep the brightness and contrast functions at low
settings. If a fixed (non-moving) pattern is left on the screen for
long periods of time at a high brightness or contrast setting, the
image can be permanently imprinted onto the screen. These
types of imprints are not covered by your warranty because they
are the result of misuse.
NOTIFICATION
This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference with radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antennas.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
I ou are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
This document is for the remote commander RM-Y136/Y137.
MODEL: KV-27S25 / 27S35 / 27V25/ 27V35 / 29RS25/ 29RS25C /
29V35C/29V65M/29V75M/32S25/32S35/32TW25/
32V25/32V35/34V35C/35V35/35V45/35V75
Please keep this notice with the instruction manual.
Note on Caption Vision
This television receiver provides display of television closed
captioning in accordance with § 15.119 of the FCC rules.
Note to CATV system installer
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Use of this television receiver for other than private viewing of
programs broadcast on UHF or VHF or transmitted by cable
companies for the use of the general public may require
authorization from the broadcaster, cable company and/or
program owner.
Owner's Record
The model and serial numbers are located at the rear of the IV.
Record these numbers in the spaces provided below. Refer to
them whenever you call upon your Sony dealer regarding this
product.
Model No.
Serial No.
4 Welcome!
4 Checking your model nmnber
Getting Started
5 Step 1: Hookup
12 Step 2: Installing the glass door and adjusting the
shelf
14 Step 3: Setting up the remote commander
15 Step 4: Setting up the TV automatically
(AUTO SET UP)
18 Changing the menu language
18 Adjusting the tilt of the picture (TILT CORRECTION)
Operations
19 Watching the TV
21 Watching two programs at a tilne--l'll'
22 Adjusting the picture (VIDEO)
23 Selecting the video mode (VIDEO)
24 Adjusting picture brightness automatically
(LIGHTSENSOR)
24 Adjusting the sound (AUDIO)
25 Using audio effect (EFFECT)
26 Selecting stereo or bilingual programs (MTS)
27 Setting the speaker switch (SPEAKER)
27 Setting audio out (AUDIOOUT)
28 Setting daylight saving time (DAYLIGHT SAVING)
28 Setting the clock (CURRENT TIME SET)
29 Setting the timer to turn the TV on and off (ON/Ot+
TIMER)
30 Customizing the channel names (CHANNEL CAPTION)
31 Blocking out a channel (CHANNEL BLOCK)
31 Setting your favorite channels (FAVORITE CHANNEL)
32 Setting video labels (VIDEO LABEL)
33 Setting Caption Vision (CAPTION VISION)
34 Operating video equipment
36 Operating a cable box or DBS receiver
Additional Information
37 Troubleshooting
38 Specifications
Back cover Index
Tile captiol_s in parentheses indicate menu name_.
Jhank yt)u lor purchasing the 5ony lrinitron Color
TV. Here are some of the features you will enjoy with
your TV:
• On-screen menus that let you set the picture quality,
sound, and other settings.
• Picture-in-Picture (PIP) that allows you to watch
another TV channel, video or cable image as a
window picture.
• Surround system that simulates the sound quality of
a concert hall or movie theater (KV-27S25/27S35/
29RS25/29RS25C/32S25/32S35/32TW25 only).
• SRS (SOUND RETRIEVAL SYSTEM) that allows
you to receive realistic sound that recaptures audio
"clues" originally present but masked in the
recording process so that the action seems to
happen all around you (KV-27V25/27V35/29V35C/
29V65M/29V75M/32 V25/32 V35/34V35C/35V35/
35V45/35V75 only).
• LightSensor TM that automatically adjusts the
brightness of the picture (KV-27V25/27V35/29V35C/
29V65M/29V75M/32 V25/32 V35/34V35C/35V35/
35V45/35V75 only).
• S-Link TM that allows you to automatically change
the TV's input mode, turn on the VCR, and play a
tape by just pressing the VCR's play button
(KV-27V25/27V35[29V35C/29V65M/29V75M/32V25/
32V35/34V35C/35V35/35V45/35V75 only). This
feature is originally designed by Sony.
The instructions in this manual are tor the eighteen
models listed below. Before you start reading, check
your model number by looking at the rear of your TV.
The KV-27S25 is the model used for illustration
purposes. Any differences in operation are clearly
indicated in the text, for example, "KV-27S25 only."
Instructions in this manual are based on the remote
commander. You can also use the controls on the TV if
they have the same name as those on the remote
commander.
Feature packages
Model
number
KV-27S25 •
KV-27S35 "
KV-27V25 • *
KV-27V35 • •
KV-29RS25 •
KV-29RS25C •
KV-29V35C • •
KV-29V65M • •
KV-29V75M " •
KV-32S25 •
KV-32S35 •
KV-32TW25 •
KV-32V25 • •
KV-32V35 " •
KV-34V35C • "
KV-35V35 • • •
KV-35V45 * • °
KV-35V75 • • °
4
_*,.q_i!i i ,_& _ _: _ : : " _}_kB
Getting Started
Although you JLdllLlbCeither an indoor o1 outdoor
antenna with your TV, we recommend that you
connect an outdoor antenna or a cable TV system to get
better picture quality.
How to connect different types of
cables
The illustrations below show examples of connecting
cables to the TV directly.
A
• VHF only
or
• VHF/UHF
or
• Cable
75-ohm coaxial cable
(Rear of TV)
VHF/UHF
B
(Rear of TV)
•"VHFUHForOrOnlYonly300-ohm twin lead| cab _VHF/UHF
• VHF/UHF Antenna connector
C 75-ohm coaxial cable
• VHF __.,,_ -,,-_
(Rear of TV)
and __HF
EAC-66 U/V mixer
-Jl (not supplied)
--J
• UHF 300-ohm twin lead cable
Notes
• Most VHF/UHF combination antennas have a signal splitter.
Remove the splitter before attaching the appropriate connector.
• If you use the U/V mixer, snow and noise may appear in the
picture when viewing cable TV channels over 37.
Connecting an antenna/cable TV
system without a VCR
If your cable company requires you to connect a ,able
box, make the connection as follows:
Cable or antenna
Cable
Cable
Cable box
(Rear of TV)
VHF/UHF
(Rear of TV)
VHF/UHF
IN |
Cable box
Cable box and cable
• KV-27S35/27V35/29V35C/29V75M/32535/32V35/
34V35C/35V35/35V45/35V75 only
(Rear of TV)
AUX
Cable box TO
CONVERTER
7S-ohm coaxial
cable (not supplied)
VHF/UHF
CATV cable __
Pay cable TV systems use scrambled or encoded signals
requiring a cable box* in addition to the normal cable
connection.
* The cable box will be supplied by the cable company.
Note
• You cannot watch the signal through AUX connector as a
window picture.
Cable and antenna
• KV-27S35/27V35/29V35C/29V75M/32S35/32V35/
34V35C/35V35/35V45/35V75 only
(Rear of TV)
AUX
CATV cable __
TO
CONVERTER
Antenna cable
VHF/UHF
Note
• Do not COlUlect anything to the TO CONVERTER connector in
this case.
Getting Started 5
Connecting an antenna/cable TV system with a VCR
To connect your VCR to the TV, first check the model
number of your TV and select the corresponding
connection. For details on connection, see the
instruction manual of your VCR.
In order to operate PIP, a VCR must be connected to
your TV and turned on (KV-27S25/27V25/29RS25/
29RS25C/29V65M/32S25/32TW25/32V25 only).
Before making the connection, disconnect tile AC
power cords of the equipment to be connected.
After making these connections, you will be able to do
the following:
• View the playback of video tapes
• Record one TV program while viewing another
program
• Watch two TV programs at once using PIP
Without a cable box
Cable
Antenna cable
VCR
I {_JOUT AUDIO VIDEO
VHF/UHF
VHF/UHF_]_ @
1
VMC-810S1820S
(not supplied)
(Rear of TV)
VIDEO IN
1 2
v
S VIDEO - .@
VIDEO-- __
AUDIO
i
R--
AUDIO OUT
:@ (VAR/FIX)
VIDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
Note
• To connect a monaural VCR, connect the audio output of the
VCR to AUDIO-L (mono) of VIDEO 1 IN on the TV.
To an S video equipped VCR without a cable box
If your VCR has an S video output jack, make the
following connections.
Cable
Antenna cable VHF/UHF
VCR
I--_OUT AUDIO VIDEO S VIDEO]
6
Getting Started
(Rear of TV)
VHF/UHF
©
VIDEO IN
1 2
_7
S VIDEO -
@@--
AU_
R--
AUDIO OUT
(VAR/FIX}
YC-15V/30V
(not supplied)
1
1
RK-74A
(notsupplied)
S VIDEO
AUDIO-R (red)
AUDIO-L (white)
With a cable box
Antenna cable
VCR
[ [_OUT AUDIO VIDFO
_._lN UNE_
OUT__
Splitter
Note
• To connect a monaural VCR, connect the audio output of the
VCR to AUDIO-L (mono) of VIDEO 1 IN on the TV.
VHF/UHF
©
VHF/UHF
t
VMC-810S/820S
(not supplied)
(Rear of TV)
r_,0Eo,.
S VIDEO I_ I
VIDEOt (_
AUtO i
I '
I
IAUDIO OUT
(VAR/RX)
AUDIO-R (red)
AUDIO-L (white)
VIDEO (yellow)
To an S video equipped VCR with a cable box
Antenna cable
VHF/UHF
OUT
_'_
Splitter
VCR
1
AUDIO VIDEO S VIDEO I
OUT
Note
• Video signals are composed of Y (luminance) and C (chroma)
signals. The S connection sends the two signals separately
preventing degradation, and gives better picture quality
compared to conventional connections.
VHF/UHF
©
(Rear of TV)
S VIDEO -
VIDEO
L
IMOtNO)
i
VIDEO IN ]
R
YC-15V/30V
(not supplied)
1
l
RK-74A
(not supplied)
_ S VIDEO
AUDIO-R (red)
-- AUDIO-L (white)
Getting Started I
7
Connecting a DBS receiver
For connection details, see tile instruction man u,fl ol
the DBS (Digital Broadcasting Satellites) receiver.
To a TV
Antenna
Satellite
antenna
input
Cable or cable box
DBS receiver
VHF/UHF
AUDIO VIDEO S VIDEO
VHF/UHF
(Rear of IV)
[_VIDEO IN
I
VMC-810S/820S (not supplied)
1
I.UDIO OUT
(VAR_FIX_
©-I-"
_ _ .
@i-0
_ IDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
Note
• You can use the S VIDEO jack or the composite video jack for
the video connection.
To a TV and VCR
Cable or cable box
8
Antenna
Satellite
antenna
input
DBS receiver
VHF/UHF I
AUDIO VIDEO SVIDEO [_ IN I
I___1°ur ]
Getting Started
VCR
VHF/UHF
SVIDEO
_]_)_F-type cable
UHF OUT (not supplied)
VHF/UHF
©
VMC-810S/820S (not supplied)
1
(Rear of TV)
"VIDEO IN
I
AUDIO OUT
(VARfFIX)
VIDEO (yellow)
--AUDIO-L (white)
ZAUDIO-R (red)
Connecting a camcorder
• KV-27V25/27V35/29V35C/29V65M/29V75M/32V25/
32V35/34V35C/35V35/35V45/35V75 only
This connection is convenient for viewing a camcorder
picture.
(Front of KV-32V35/34V35C/35V45/35V75)
(Front o| KV-27V25/27V35/29V3bL/
29V65M/29V75M/32V25/35V35)
Video and
audio output¢_
VIDEO "_
(yellow) _
VMC-810S/820S
(not supplied)
I
Note
• To connect a monaural camcorder, connect the audio output of
the camcorder to AUDIO-L (mono) of VIDEO 2 INPUT on the
TV.
AUDIO-R
(red)
AUDIO-L
(white)
VIDEO --_
(yellow) _
_ UDIO-R
(red)
AUDIO-L
(white)
Connecting an audio system
When connecting audio equipment, see page 27 for
more information.
(Rear of TV)
VHF/UHF
VIDEO IN
1 2
_7
S VIDEO - -(_
AUDIO OUT
(_,_t) - .
AU,=O O
R--
RK-74A (not supplied) ....
AUDIO OUT-L (white)
-3>
AUDIO OUT-R (red)
/_ Set the anlplifier's
A A functi°n to line input.
_ipet_ _ _
o111 1
L
Getting Started I
9
Connecting two VCRs for tape editing using MONITOR OUT
• KV-27V25/27V35/29V35C/29V65M/29V75M/32V25/
32V35/34V35C/35V35/35V45/35V75 only
MONITOR OUT allows you to record a program that is
on the screen. (Rearof IV)
VCR (for playback)
I AUDIO VIDEO
[__ LINE
OUT
t
VMC-810S/820S
(not supplied)
_UNK
OUT CONTROL S
AUO,O-R(red)--
AUDIO-L (white) ---_-_
VIDEO (yellow) --_
VCR (for recording)
AUDIO VIDEO
Lt_t_fL"E
?
i
VMC-810S/820S
(not supplied)
[he above type of COlmection should only be used
when you connect from the line input of one VCR, and
from the line output of a second VCR.
Notes
• Do not change the input signal while editing through
MONITOR OUT, or the output signal will also change.
• You can use the S video jack to connect a VCR for playback
and the composite video jack to connect a VCR for recording.
• When connecting a single VCR to the TV, do ]lot connect tile
MONITOR OUT jacks at the rear of the TV to the VCR's line
input, while at the same time connecting from the TV's VIDEO
IN jacks to the VCR's line output, as shown below.
X (Rear of TV)
EO IN IT] [TIMONITOFI[
LIJLIJOUT I
vc _
I %TI
Using the S-Link function
• KV-27V25127V35129V35CI29V65M/29V75M/32V251
32V35/34V35CI35V35135V45/35V75 only
The S-Link feature allows you to operate the TV and
VCR with the S-Link function in the following ways:
• When you press the VCR's play button, the TV's
input mode is automatically changed to video, and
the VCR starts playing a tape.
VCR
• When you press tile VCR's stop button, the IV
automatically returns to the previous input mode.
• You can turn off the TV and VCR together using the
SYSTEM OFF button (see page 35 for details).
Note
• The TV may malfunction if you connect the S-Link cable to tile
TV without connecting the other end of the cable to the VCR.
(Rear of TV)
10
AUDIO VIDEO
'" I@
LINE
I
LINE OUT_
Getting Started
, VIDEO (yellow)
') @ I_UNK
AUD
Audio/video cable !_==
(not supplied)
S-LINK OUT
IN
VIDEO 1 I _DEO 3
. --sv,oEO ol_auT.u7q
_(_)__ S-LINK _
OUT CONTROL S IN
II lllill
Connecting an AV receiver
Connect all optional AV receiver to tile VIDEO 1IN
jacks at the rear of the TV.
VIDEO (yellow)
AUDIO-L (white)
AUDIO-R (red)
I
VMC-810S/820S (not supplied)
(Rear of KV-27V35
] IN
J_ !wDEO3 - S VIDEO _ W
__,05
i _ ...
OUT
.0_ iivA_x
@
-@-@
-@-@
-- AUDIO-R (red)
AUDIO-L (white)
VIDEO (yellow)
Monitor _ _ Monitor audio
video output
output
AV receiver
]_ o = .......... 'g_7
1
VMC-810S/820S (not supplied)*
TVaudio _ _ _ TV video input
input
?
* (KV-27V35/29V35C/29V75M/32V35/34V35C/35V45i
35V75 only)
Make this connection if your TV has the TV OUT
jacks. When you connect an AV receiver to the TV
using the AV receiver's TV input jacks, it is
recommended to set VIDEO 1 IN's video label to
"RECEIVER" (see page 32 for details).
Getting Started 1 1
• KV-32TW25/35V75 only
Follow these instructions to install tile glass door and
adjust the shelf.
Push here to close.
To open, push again.
Parts List
O Bottom hinge _ 1
0 Top hinge _ 1
0 Screw 4 x4 _ 4
O Plate pad _ 1
O Plate _ 1
Installing the glass door
1
Check that the projection of the screw
through the hinge allows for proper
installation of the hinge to the glass door,
and then insert the bottom hinge O into
the hole located at the bottom, right side
of cabinet.
projection of this
f screw
2
3
Attach the top hinge O to the right side of
the glass door, tighten the screws snugly,
but do not overtighten. Attach the plate
pad O to the left side and push the plate O
over the plate pad.
Push the top, glass door hinge into the top,
right bushing and gently slide the glass
door into the bottom hinge. Adjust the
glass door until level, and tighten the hinge
screws.
12
Getting Started
Note
* The glass door is made of tempered glass. Although it is more
shock-resistant than ordinary glass, tempered glass may
shatter if it is dropped or receives a sudden shock.
Adjusting the shelf
1 Unlock the four shelf supports with a
medium Philips head screwdriver. Turn the
screwdriver 90 ° to unlock the shelf
supports.
2 Gently slide the shelf up and out.
3
Insert shelf supports in the appropriate
holes. Slide shelf in, align the shelf grooves
with the shelf supports, and slide the shelf
down.
Getting Started 1
Getting to know buttons on the
remote commander
Names of buttons on the remote commander are
indicated in different colors to represent the available
functions.
Inserting batteries
Insert two size AA (R6) batteries (supplied) by
matching the + and - on the battery to the diagram
inside the battery compartment.
Notes
• Under normal conditions, batteries will last up to six months.
If the remote commander does not operate properly or the
indicators of the buttons on the remote commander do not
light up, the batteries may be worn out. When replacing
batteries, replace both of them with new ones.
• Do not mix old batteries with new ones or mix different types
of batteries together.
• If the electrolyte inside the battery should leak, wipe the
contaminated area of the battery compartment with a cloth and
replace the old batteries with new ones. To prevent the
electrolyte from leaking, remove the batteries when you don't
plan to use the remote commander for a long period of time.
• Do not handle the remote commander roughly. Do not drop it,
step on it or let it get wet.
• Do not place the remote commander in direct sunlight, near a
heater, or where the humidity is high.
Button color
Transparent ....... TV/VCR/DBS/Cable box function
(light up) buttons. Press the appropriate
function button first to change the
remote commander's function.
Green .................. Buttons relevant to power operations.
Label color
White .................. TV/VCR/DBS/Cable box operation
buttons.
Yellow ................. PIP operation buttons.
Blue ..................... DBS operation buttons.
Blue
Blue--
DLTO
O® ®®
CD CD _ (Z)
®®®
®®®
®®®
o®o
2@2
®G
SONY
--Green
--Transparent
Yellow
Blue
14 IGetting Started
You call set up your TV easily by using the AUTO SET
UP feature. It presets all the receivable channels.
To set up the TV manually, see "Setting cable TV on or
off" (page 11) and "Presetting channels"(page 17).
(Front of TV)
SET UP TV/VIDEO - VOLUME + - CHANNEL + POWER
oGOZ) o
For KV-27V35/29V35C/29V75M/32V35/34V35C /
35V45/35V75, the control buttons are located on the
top of the TV.
Before you start using AUTO SET UP, be sure to
connect the antenna or cable to the TV (see
page 5).
1 Press POWER to turn on the TV.
The AUTO SET UP screen appears.
POWER
Note
• The AUTO SETUP screen appears whenever you press
the POWER button ifyou do not execute AUTO
PROGRAM.
ENGLISH : [CH+)
ESPAff, IOL : [CH-]
AUTO SET UP : [VOL-]
DEMO : [TVNIDEO]
First please connect
the antenna.
Press [SET UP] to exit.
2
(Except Canadian models)
Press CHANNEL + to select English screens
or CHANNEL - to select Spanish screens.
- CHANNEL +
3
Press VOLUME -.
-- VOLUME +
AUTO PROGRAM
"AUTO PROGRAM" appears on tile screen and
the TV starts scanning and presetting channels
automatically. When all the receivable channels are
stored, "AUTO PROGRAM" disappears and the
lowest numbered channel is displayed. If the TV
receives cable TV channels, CABLE is set to ON
automatically.
To perform AUTO SET UP again
1 Press SET UP on the TV.
2 (Except Canadian models)
Press CHANNEL + or CHANNEL - to select the
language.
3 Press VOLUME -.
The picture and sound settings will be set to the
factory preset conditions.
4 Press CHANNEL +.
"AUTO PROGRAM" appears on the screen and the
TV starts scanning and presetting channels.
5 Press CHANNEL - to exit the AUTO SET UP menu.
To exit AUTO PROGRAM
Press any button.
Notes
• If the TV is set to a video input, you cannot execute AUTO SE'I
UP. Press TV (black button) so that a channel number appears.
• Using the AUX connector, press TV (black button) first and
make sure that "AUX" is displayed beside the channel number
on the screen. Then follow the procedure above to perform
AUTO SET UP. (KV-27S35/27V35/29V35C/29V75M/32S35/
32V35/34V35C/35V35/35V45/35V75 only)
To browse the main functions (DEMO)
Press TV/VIDEO on the TV in step 3. The functions
and menus are displayed one by one.
To exit DEMO
Pressany button.
Getting Started I
15
Erasing or adding channels
After AUTO SET UP, you can erase unnecessary
channels or add the channels you want. Preset channels
during the day rather than late at night, when some
channels may not be broadcasting.
CD CD ¢!_
oe_)e
o ® ® ®
(Z) CZ) C:D C2)
_®QI
SONY
-- TV (FUNCTION)
-- 0- 9 buttons
-- ENTER
_f
-- MENU
-- CH +/-
1
Press TV (FUNCTION).
FUNCTION
rv
2
Press MENU.
The main menu appears.
I _VIDEO I
MODE :STANDARD
MENU PICTURE m_mmm
HUE
(_ l_ cOLOR I---I
| _ BRIGHTNESSIII,,I_ I
lira1 SHARPNESS IIlllum_ I
I I
I use_ _ Exit_ I
3
Press 4,or € to select ___,and press C_.
The SET UP menu appears.
CHANNEL ERASE/ADD I
CHANNEL CAPTION
CHANNEL BLOCK
FAVORITE CHANNEL
I ICABLE : ON l
I Ie:m I AUTO PROGRAM I
4
Press t or € to select CHANNEL ERASEIADD,
and press _.
The CHANNEL ERASE/ADD menu appears.
Use[0 - 9]or [CH+/-]
tu::_ _ channel Exit_ I
5
Erase andlor add channels:
To erase an unwanted channel
(1) Make sure the cursor (P') is beside ERASE.
(2) Press CH +/- or the 0 - 9 buttons to select the
channel you want to erase, and press ENTER.
CH
Selected channel number
CHANNEL ERASE/ADD _L)
®®®
@ @ @ % tUse[Oect9]h°r[¢CaHn:elI
®,6. u,,oo-oI
(3) Press CD.
The "-" indication appears beside the channel
number, showing that the channel is erased
from the preset memory.
To add a channel that you want
(1) Press tt or € to move the cursor (I_) to ADD.
(2) Press the 0 - 9 buttons to select the channel you
want to add, and press ENTER.
Selected channel number
®®®
®®®
@@@%
®'6"
(3) Press _.
The "+" indication appears beside the channel
number, showing that the channel is added to
the preset memory.
6 To erase and/or add other channels, repeat
step 5.
16 IGetting Started
7
Press MENU to return to the original screen.
MENU
Notes
• If you erase or add a VHF or UHF channel, tile cable TV
channel with the same number is also erased or added, and
vice versa.
• Erasing and adding channels is also available for the AUX
input. (KV-27S35/27V35/29V35C/29V75M/32S35/32 V35/
34V35C/35V35/35V45/35V75 only)
Setting cable TV on or off
If you have connected the TV to a cable TV system, set
CABLE to ON (the factory setting). If not, set CABLE to
OFF. You do not have to do this procedure if you
execute AUTO SET UP (page 15). Do this procedure
only when you want to set it manually.
1 Press MENU.
2 Press • or • to select _, and press _.
3
Set CABLE to ON or OFF:
(1) Press t1'or } to move the cursor (1_) to CABLE,
and press C?D.
(2) Press t or • to select ON or OFF, and press (_.
TL
CHANNEL ERASE/ADD
I h I CHANNEL CAPTION
| m_d CHANNEL BLOCK
FAVORITE CHANNEL
[]_CABLE : OFF
Ir_ I AUTO PROGRAM
Use _ _ Exit
4 Press MENU to return to the original screen.
Presetting channels
You can preset TV channels easily by using the AUTO
PROGRAM feature. You do not have to do this
procedure if you execute AUTO SET UP (page 15). Do
this procedure only when you want to set it manually.
1 Press MENU.
2 Press • or • to select _, and press o_.
3
Press t or 4 to select AUTO PROGRAM, and
press _.
AUTO PROGRAM
"AUTO PROGRAM" appears on the screen and the
TV starts scanning and presetting channels
automatically. When all the receivable channels are
stored, "AUTO PROGRAM" disappears and the
lowest numbered channel is displayed.
4 Press MENU to return to the original screen.
To exit AUTO PROGRAM
Press any button.
Notes
• If the AUTO PROGRAM menu appears in gray, the TV is set tu
a video input and you cannot select AUTO PROGRAM. Press
TV (black) so that a channel number appears.
• Presetting channels is also available for the AUX input.
(KV-27S35/27V35/29V35C/29V75M/32S35/32 V35/34V35C/
35V35/35V45[35V75 only)
Note
• If CABLE appears in gray, the TV is set to a video input and
you cannot select CABLE. Press TV (black button) so that a
channel number appears.
Getting Started 17
• Except Canadian models
if you prefer Spanish to English, you can change the
menu language. You do not have to do this procedure
if you select the language during AUTO SET UP
(page 15).
1 Press MENU.
2 Press t or 4 to select _, and press _.
3
Press t or • to select LANGUAGE, and press
SET UP
V_ CHANNEL ERASE/ADD
II , I CHANNELCAPTION I
I _ CHANNEL BLOCK I
I_ FAVORITE CHANNEL I
CABLE : ON
II1_ AUTO PROGRAM I
I1--[ LANGUAGE : ENGLISH I
I DMENU IUse _ _ Exit
4 Press t or • to select your favorite
language, "ENGLISH" or "ESPAI_IOL," and
press @.
AJUSTES .
BORRAR/ANADIR CANAL
NOMBRE DEL CANAL
BLOQUEAR CANAL
CANAL FAVORITO
CABLE : SI
I I_] I AUTO PROGRAMA(_ION
]I I)LENGUAJE : ESPANOL
I DMENUUsar Ira} {33 Salir _
5 Press MENU to return to the original screen.
Note
• Certain parts of the Spanish menus remain in English.
• KV-35V35135V45/35V75 only
You can adjust the tilt of the picture if it is not aligned
with the TV screen. Misalignment may be caused by
the direction of the earth's magnetic fields in relation to
the position of the TV.
1
2
3
o®o I
Press MENU.
Press tt or • to select _, and press __}.
Press t or • to select TILT CORRECTION, and
press c_.
;ET UP
O.A, ,'
CHANF I
CHANNEL BLOCK I
FAVORITE CHANt, I
CABLE : ON
AUTO PROGRAM I
VIDEO LABEL I
TILTCORRECTION : 0 /
_MENU
use _i} Gg Exit_ /
4 Press 4,or • to adjust the tilt between +5
and -5.
5 Press MENU to return to the original screen.
Notes
• If your house is located near a high-voltage cable or is of
reinforced concrete, you may not be able to correct the tilt of
the picture properly. Consult your nearest Sony dealer.
• If there are large speakers near the TV, the tilt of the picture
cannot be corrected properly. Place the TV away from the
speakers.
18 Getting Started
m
Opera tions
1
MUTING --
DISPLAY --
SLEEP --
JUMP i
VOL +/---
O@_e
801'q'Y
-- TV (POWER)
--TV (FUNCTION)
_TV/VIDEO
--TV (black button)
--0- 9 buttons
--ENTER
-- CH +/-
Press TV (POWER) to turn on the TV.
POWER
2
If "VIDEO" appears on the screen, press TV (black
button) so that a channel number appears.
Press TV (FUNCTION).
FUNCTION
TV
Once you press TV (FUNCTION), the TV function
is set unless another function button is pressed.
3
Select the channel you want:
To select a channel directly
Press the 0 - 9 buttons, and press EN'IER.
To scan through channels
Press CH +/- until the channel you want appears.
CH
®@®
®
The channel can also be selected without pressing
ENTER.
4 Press VOL +/- to adjust the volume.
VOL
VOLUME
IIIIInlllllll!lllllll.,.,..,,,, .,,,,,,.,,,.,,,
Switching quickly between two
channels
You can use the JUMP button to switch or "jump" back
and forth between two channels.
Press JUMP.
JUMP
Pressing JUMP again switches back the channel.
Note
• You cannot jump to channels you scanned through using the
CH +/- buttons.
Muting the sound
Press MUTING.
"MUTING" appears on the screen.
MUTING
To restore the sound, press MUTING again, or press
VOL +.
Operations I 19
Displaying on-screen information
Press DISPLAY repeatedly until the desired
display appears.
Each time you press DISPLAY, the display changes as
follows:
Status display* --* XDS** _ Caption Vision***
T DISPLAY OFF ÷--]
DISPLAY
* Channel number, the current time (only for
available models), channel caption (if set), and MTS
mode (if SAP is selected) are displayed. SAP
indication disappears after three seconds.
** Some programs are broadcast with XDS (Extended
Data Service) which shows a network name,
program name, program type, program length, call
letters, and time of the show. When you select XDS
with the DISPLAY button, this information will be
displayed on the screen if the broadcaster offers this
service.
***Some programs are broadcast with Caption Vision.
When you select Caption Vision with the DISPLAY
button, Caption Vision will be displayed on the
screen if the broadcaster offers this service. (See
page 33 for selecting Caption Vision.)
To cancel the display, press DISPLAY repeatedly until
"DISPLAY OFF" appears. "DISPLAY OFF" goes off
after three seconds.
Setting the Sleep Timer
The TV stays on for the length of time you specify and
then shuts off automatically.
Press SLEEP repeatedly until the time (minutes)
you want appears.
Each time you press SLEEP, the time changes as
follows:
30 ---*60 _ 90 ---*SLEEP OFF
t /
SLEEP
To cancel the Sleep Timer, press SLEEP repeatedly
until "SLEEP OFF" appears, or turn off the TV.
20 Operations
Watching a video input picture
Press TVNIDEO repeatedly until the desired
video input appears.
Each time you press TV/VIDEO, the display changes
as follows:
• KV.27S25127S35/29RS25129RS25CI32S25132S351
32TW25 only
TV _ VIDEO 1 _ VIDEO 2
T I
• KV-27V25/27V35/29V35C/29V65MI29V75M/32V251
32 V35/34V35C/35V35135V45/35V75 only
TV --_ VIDEO 1 ---*VIDEO 2 ---*VIDEO 3
T I
TV/V ID EO
To return to the TV picture, press TV (black button) so
that a channel number appears.
Changing the VHF/UHF input to the
AUX input
• KV-27S35127V35/29V35C/29V75MI32S35132V351
34V35C/35V35/35V45/35V75 only
Press TV (black button).
TV
Pressing TV (black button) again switches back to the
previous input.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Sony KV-32V25 Owner's manual
- Category
- LCD TVs
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
