SPORTSTECH F38 User manual

Page is loading ...

Contents

PAGE

Safety instructions

Assembly list

Product part list

Assembly instructions

Product description

Routine maintenace

Troubleshoot

Table of content

Page

Safety instructions

01

Read all instruction carefully before use this product. Retain this owner’s manual for the future’s reference:

----Attach the safety pull pin rope to your clothes while using the treadmill.

----When you are running, keep your hand swinging natural, look forward, never look down at your feet.

----Add the speed step by step when running.

--

--When emergency happens, pull the “safety pin" off the socket immediately.

----Leave the treadmill after the running belt stop stably.

ATTENTION

01- Make sure your health status is suitable for exercising and over exercising may cause damage to your health

02- The machine is not suitable for children unless they are under the supervision of adults. One who's disabled

physically and mentally or lack of common sense of mechanism is not suggested use the machine.

03- The machine is only for home exercising and is not capable for professional training or medical treatment.

04- The heart rate displayed on the console could not be used as clinical data.

05- Please turn to the professional for help if the power cable is broken.

06- Please check all the parts, bolts and nuts are well fastened before use.

07- Wear appropriate clothing when exercising on the treadmill. Do not wear long, loose fitting clothing that may be

caught in the treadmill. Always wear running or aerobic shoes with rubber soles.

08- Lay the machine on clean and flat floor and keep it from wet or heat sources.

09- DO NOT touch any motion part with your hands.

10- The machine can be used by one at one time.

11- Please use the original spare parts for replacement.

12- The machine is of Class HC, the max user weight should not go over 150kg.

Caution: Read the assembly instruction carefully and follow the instruction when assembling.

IMPORTANT SAFETY PRECAUTION

1. Power

· Plug the treadmill directly into a dedicated grounded circuit, which provides a path of least resistance for

electric current to reduce the risk of electric shock.

· Place the treadmill in a suitable place so that the wall plug is visible and accessible.

· Make sure the plug complies with the socket.

· Power input: 220v-240v AC

2. DO NOT let the power cable connect the roller; DO NOT lay the cable on the running belt; If you observe any

damage or wear on the mains plug or on any section of the mains lead then please have these replaced immediately

by a qualified electrician – do not attempt to change or repair these yourself.

3. Please unplug the machine for cleaning or maintenance.

WARNING: It could cause damage to human body or machine if the machine is not unplugged.

4. Take sure the power supply is connected and the safety lock is effective before using the treadmill. Fit one side of

the safety pin on the treadmill and clip the other side on your clothes or belt, which will enable you to pull off the

safety pin promptly in an emergency.

5. DO NOT use the machine in area with high humidity or temperature or outdoors.

6. When the treadmill is not being used, the power cord should be unplugged and the safety pull pin removed.

7. Always attach the safety pull pin rope to your clothing when using the treadmill. If the treadmill should suddenly

increase in speed due to an electronics failure or the speed being inadvertently increased,

the treadmill will come to a sudden stop when the pull pin is disengaged from the console.

8. In case of any abnormality during the use process, please remove the safety lock immediately,

grasping the handlebar and jumping onto the two edgings, then get off the treadmill after it stops.

9. Before starting any exercise program, consult with your physician or health professional. He or she

can help establish the exercise frequency, intensity (target heart zone) and time appropriate for your particular age

and condition. If you have any pain or tightness in your chest, an irregular heartbeat, shortness of breath, feel faint or

have any discomfort while you exercise,

STOP! Consult your physician before continuing.

Page

Assembly list

02

Running Deck

Enhancing Bar

Bolt

M8*15 x 16 pcs.

Busher

8x 16 p

cs.

6mm wrench x 1 pcs.

5mm wrench x 1 pcs.Lub

rication oil Safety pin

Tool Set

Console Post Console

WARNING: Damage caused by unproper assembly will not be covered by warranty.

PACKING LIST

TOOL SET

1. Please read the instruction carefully before assembling the machine.

2. Take out and lay the hard ware on clean floor to better assemble the machine.

3. Check all the parts according to the packing list and see whether all parts are available.

4.

Please handle the product with care.

5. Please handle the packing material or tools properly in case of causing hazard to children.

6. Please assemble the machine with the guidance of the instruction.

7. Only adults or professional can assemble the machine.

10- The machine can be used by one at one time.

11- Please use the original spare parts for replacement.

Page is loading ...

Page

Product part list

04

33

2

34

63

No. Qty. No. Qty.Name Name

Main frame Nylon busher

Cylindrical cushion

Cone cushion

Edging fixator

Adjustable feet

Motor rubber cushion

Front roller

Running belt

Rear roller

Running board

Motor

PCB

Rejector

Over current protector

Power switch

Air cylinder

Casing

Pulse sensor support

Pulse sensor

TFT display

Handle bar button

Safety pin set

Mp3 socket

Console panel button

console connection cable

Loudspeaker

Extension cable

Multi groove belt

Fan

PWM connection cable

Incline motor

Bottom frame

Incline support

Console frame

Running board support

Motor fixator

Upper motor cover

Bottom motor cover

Left end cap

Right end cap

E

dgings

Bottom console cover

Upper console cover

Console panel

Left handle bar

Right handle bar

Left handle bar button lid

Right handle bar button lid

Loudspeaker support

Fan support

Fan grille

Fan decoration cover

"STOP" button

"START" button

Vaulted feet

Vaulted feet wheels

Flat busher

Enhancing bar

Transportation wheels

Spacer sleeve

Right console post

Left console post

Page

Assembly instructions

05

Console

Console Post

Handle Bar

Edging

Right console post

Location for cable

connection

Left console post

Motor Cover

Hand Pulse Sensor

Running Belt

console

Location for cable connection

Step 1

Fix the console posts onto the main frame

Step 2

Fix the console onto the posts

A

: Connect the extension cable with PWM cable. Cable should go through the right console post.

B: Lock both of the console posts onto the bottom frame with M8*15 bolt x 6pcs and busher x 6pcs

(Note: Don't fasten the bolts)

A: Connect the console cable with the extension cable

B: Lock the console onto posts with M8*15 bolt x 6pcs and busher x 6pcs

(Note: Don't fasten the bolts)

Page

Assembly instructions

06

Enhancing Bar

Fix the enhancing bar onto the console posts

Step4

Fasten all the bolts from Step 1 to Step 3

Lock the bar onto the two posts with M8*15 bolt x 4pcs and busher x 4pcs

(Note: Don't fasten the bolts)

Page

Product description

07

112CM

152CM

85CM

131.5 cm

187 cm

Unfold the treadmill

Switch

1. T

u

rn on the treadmill

2. How To Use The Safety Pin

Plug the treadmill to power supply and switch on.

The computer will be lighted with a "Beep".

The machine can only be in operation when the safety pin is

in the safety pin socket.

If any emergency, pull the pin out of the socket and the

treadmill will stop immediately. Return the pin into the

socket to re-start using.

Fold the treadmill

3

. U

nfold and fold the treadmill

Folding the treadmill helps save the space. Before folding the treadmill, please switch the

power and remove the power cable from the treadmill.

To fold the machine, raise the running board by holding the handle at the rear end of the

main frame until the cylinder is locked.

To unfold the machine, slightly kick the yellow joint part of the cylinder and press

downward the running board a bit, then the running board will fall down naturally.

Slightly kick the yellow joint

part of the cylinder and press

downward the running board

a bit, then the running board

will fall down naturally.

Page

Product description

08

0:00 30:00

0:0 N/A

N/A

0

0 50

Set Up Range

8:00-99:00

N/A

1.0－99.00

20－990

0:00-99:59

1.0－20

0-15

0.0－99.9

0

－999.9

0:0 1:00

4. Console Operation Ins

truction

A\ Technical Parameter

B\ Console Operation

"START" Button

"STOP" Button

Initial Data Display Range

Set Initial Data

Press "START" button to run the treadmill.

Press "STOP" button to stop the treadmill.

Hold "STOP" button for a few seconds to reset

the computer.

Then press "START" button to continue exercise.

Speed adjustment button on right handle bar

Press "+" or "-" to increase or decrease the speed.

Time(MIN:SEC)

Speed(KM/H)

Incline(%)

Distance(KM)

Calorie(KCAL)

Page

Product description

09

Enter the operation interface

Settings

Entertainment

Scene

Records

Work Out Data

User Information

Incline adjustment button on right handle bar

Press " " or " " to increase or decrease the

incline degree.

Touch "Sports" icon to enter the

operation interface

Touch "Settings" icon o

r

enter interface

of "Settings". User can adjust the settings

of "Wi-Fi", "Display", "Sound" and "Language".

Touch "Entertainment" iconn o

r

choose music

play, video play and internet browsing.

Touch "Scene" iconn

o

r

enter "Scene Mode",

there will be 3 scenes for users to explore

Touch "Records" iconn

o

r

check the records

of each and total work out results.

Touch "Work Out Data" iconn o

r

check the

data of work out simultaneously

Touch "User Information" icon to register and

store the user information (while connect to WiFi )

Work out data can be stored after log in

Page

Product description

10

The display will monitor Time (M:S), Pulse(Bpm), Speed(Km/h), Incline(%), Distance(Km),Calories(Kcal).

The blue circal stands for 400m athletic track.

User may choose other training modes listed at the bottom of the interface by touching the corresponding

icons or by sliding the screen.

Touch "Speed" or "Incline" and then choose the value. User also can adjust the value by touching "+/-".

5. Intructions of Sports Inter

face Operation

1)Touch icon "Sports" and enter "Rapid Weight Loss" training mode, as below:

2) Touchh

"Start" icon to start the training.

3) While running, touchh

o to return to the main page, and touchh

o to enter system set up

4) Touchingg

will end the running and the machine will slow down and stop.

5) Touchh

or

to end the display of the work out records. User can share the records on "Facebook" or "Twitter".

Page

Product description

11

3) Touc hh

4) Touc hh

2) Touchh

3) Touchh

1) There are 3 user programs (User1-User3) for customized set up.

In "User" mode: user can set speed, incline and training time.

Default sections: 1;Setting Range: 1-20;Default Speed: 1.0KM/H;Setting Range: 1.0-20.0KM/H; Drag

blue square to set the speed;Default Incline: 0°;Setting Range: 0-15°;

Drag yellow square to set the speedDefault Time: 30:00; Setting Range: 8:00-99:00

Training time for each section is 1/20 of the setting time.

to exit User mode

to start training program.

4) Speed and incline is open for manual adjustment during program training.

5) The machine will stop operation when training time ends or it can be stopped manually.

6. Training Program

1). Touch "Sports" icon

and then "Program" icon to enter below interface

1) Slide the screen to choose different training programs among the 12 ones: Fat Burning Mode, Health Mode, Highway

Mode, Mountain Mode, Beach Mode, Plastic body Mode, Middle-aged Mode,Elderly Mode,

Diet Mode, Walking Mode, Female Mode, Male Mode

2) Default training time is 30:00, user can set the time accordingly within the range of 8:00-99:00.Each program is

divided into 20 sections, training time for each section is 1/20 of the setting time.

to exit program training.

to start training program.

5) Speed and incline is open for manual adjustment during program training.

6) The machine will stop operation when training time ends or it can be stopped manually.

2). Touch "User" to enter customized training program as below

3). Touch "Target" to enter Target Training Mode as below

Page

Product description

12

Slide the screen to choose the target training program: Time Countdown, Distance Countdown, Calories Countdown

b. Touc

hh

c. Touc

hh

b. Touc

hh

c. Touc

hh

A) Time Countdown

a. Default training time is 20:00 with the setting range of 8:00-99:00

to exit User mode

to start training program.

d. Speed and incline is open for manual adjustment during program training.

e. The machine will stop operation when training time ends or it can be stopped manually.

B) Distance Countdown

a. Default training distance is 1.0KM with the setting range of 1.0-99.0KM

to exit User mode

to start training program.

d. Speed and incline is open for manual adjustment during program training.

e. The machine will stop operation when complete the distance or it can be stopped manually.

C) Calories Countdown

a. Default training calories target is 50 with the setting range of 20-990 Kcal

to exit User mode

to start training program.

d. Speed and incline is open for manual adjustment during program training.

e. The machine will stop operation when complete the calories target or it can be stopped manually.

A.Definition: HRC is a mode under which the speed will automaitcally change according to the comparison between

the user's heart rate and the pre-set heart rate targets. User can use wireless heart rate tansimitor or hand pulse

sensor to test the heart rate.

B.The max speed under HRC Mode is 11KM/H.

C.How to Set HRC and the setting range

a) Default age:25; setting range: 15-80

b) Default heart rate (Pulse) target: (220-age)*0.6; setting range: 80-180

c) Default Time: 30:00; setting range: 5:00-99:00

D.Systematic speed adjustment

a) Frequency: HRC collects users' heart rate every 30s;

b) Machine will accelerate by 2.0KM/H when users' heart rate is 30 beats/min lower than the target

c) Machine will accelerate by 1.0KM/H when users' heart rate is 1-29 beats/min lower than the target

d) m

achine will decelerate by 2.0KM/H when users' heart rate is 30 beats/min higher than the target

e) Machine will decelerate by 1.0KM/H when users' heart rate is 1-29 beats/min higher than the target

E.Machine will decelerate to lowest speed within 20s and then stop operation 15s afterwards with beeps per second

when encounter below circumstances

a) heart rate is out of detection twice (once in 30s)

b) Users' heart rate decelerate the machine when speed is 0.8KM/H

c) Users' heart rate is over the target(220-age)*0.6

F. Default lowest speed is 0.8KM/H. When current speed is 1.8KM/H and users' heart decelerate the speed by

2.0KM/H, the final speed will be 1.8KM/H

G. Incline is only adjusted manually

H. Initial speed is 0.8KM/H and systematic speed adjustment is applicable 1 min after start.

4). Touchh to

enter "HRC" Mode as below

b. Touc

hh

c. Touc

hh

Page

Product description

13

8. Share Th

e Work Out Rec

ords

a) C

ountry Road (2.0KM counting down, machine will stop when distance whole distance completed or

user can stop the training manually)

b) Open Valley (3.0KM counting down, machine will stop when distance whole distance completed or user

can stop the training manually)

c) City Street (4.0KM counting down, machine will stop when distance whole distance completed or user

can stop the training manually)

User can adjust speed and incline through

touching the icons on screen or buttons

on handle bars

2) Touch "Start" to start scene training

3) Adjust Speed and Incline

After work out, touchh rr o share the records with your friends

Log in with right access and code of users' facebook account and work out record will be shared

7. T

ouch "Scene" To Enter Scene Training Mode

1) Slide the screent to choose different scenes: ：Country Road、Open Valley、City Street

Page

Product description

14

Pre-set Program

Instrcution of starting the machine

A. Start the machine

1. Touch "Start" and the moter will start rolling after 3s count down

2. Touch "Speed" and then touch"+" on the screen can accelerate the machine. Max Speed is 20KM/H

3. Touch "Speed" and then touch "-" on the screen can decelerate the machine. Min Speed is 0.8KM/H

4. Press the buttons on handle bars to adjust the speed, same function as the above

5. Touch "Incline" and then touch "+" on the screen can increase the incline. Max incline is 15°.

6. Touch "Incline" and then touch "-" on the screen can decrease the incline. Min incline is 0°.

7. P

ress the buttons on handle bars to adjust the incline, same function as the above

8. Touch "Stop" or press the "Stop" button on the control panel to stop the machine.

Training Time / 20 = Each Section Time

Setions

Program

Fat Burning Mode

Health Mode

Highway Mode

Mountain Mode

Beach Mode

Plastic body Mode

Program

Middle-aged Mode

Elderly Mode

Diet Mode

Walking Mode

Female Mode

Male Mode

Code Code

Page

Routine maintenace

15

Treadmill Maintenance

Adjust The Running Belt

How To Tighten The Belt

How To Adjust The Belt Drifting

Lubrication

maintain the good performance of the treadmill.

H

ow to lubricate

Move and Fold

B. Safety Lock

Pull the safety lock off can stop the machine during any operation. Screen will display "Safety lock off,

please pay attention to check!" Retrun the lock and machine will reset.

Maintenance is very important to the normal operation of the treadmill. Improper maintenance may damage

the machine and shorten it's life expectancy. Make sure all the parts are well fastened during the assembly

and replace promptly the broken parts.

This treadmill is equipped with a pre-lubricated, low maintenance deck system. But after the using of the

first few weeks, user might need to adjust the running belt. Users' weight and different running gestures

might cause slip or drift of the running belt.

Step 1. Turn the left adjusting bolt 1/4 clockwise with 6mm wrench.

Step 2. Turn the right adjusting bolt 1/4 clockwise. Make sure to turn the two bolts same distance,

otherwise the running belt will drift.Step 3. If the belt is still loose and slips during running, repeat the above

steps to tighten the belt. Note：Please don't tighten the belt too much as it may cause damage to the roller

and other parts. To loosen the belt, turn the adjust bolts counterclockwise.

Belt Drifting happens when the user's feet cause different pressure to the belt.

F

ollow the below steps to adjust the belt.

Step 1. Let the treadmill run at speed of 6KM/H

Step 2. Observe the status of the belt drifting. If it drifts to the left, turn the left adjusting bolt 1/4 clockwise. If it

drifts to the right, turn the right adjusting bolt 1/4 clockwise. Repeat the adjustment and sure the roller is horizontal.

Step 3. Increase the speed to 14KM/H and observe the status of belt. If any drifting,

slow down the speed and adjust the bolts again.

Note: Once the belt returns to normal state, make sure the belt is well tightened.

The running board has been pre-lubricated, but a frequent check of the running board will help

1. Location for lubrication is the middle part between the belt and board.

2. Cut the lubrication oil bottle

3. Spread the oil in the middle part between the belt and board. Then press the belt and slowly move

it backward to apply the oil evenly on the board.

The treadmill has transportation wheels for easy move. Please switch off the power

and fold the running board before moving it.

Page

TROUBLESHOOT

16

TROUBLE SHOOTING

A. Error Code Analysis And Solution

Note: For other problems, please contact local distributors for help.

Cleaning

Frequent clearing helps prolong the treadmill's performance.

WARNING: Make sure the power is cut off during clearing.

After using, clean the sweat or other dust with wet clean towel.

Note: Please don't use any acidic liquid or pure any liquid directly onto the machine, or the electrical parts will be

damaged. Also don't expose the treadmill in the sunlight. Each week: Clean the dust on floor each week.

for the control board is melted

b) Check whether the cable between the control board and PCB is well connected

c) Check whether the cable between the control board and transformer is well connected

2. To display of pulse or disorder display of it

a) Check whether the sensor cables are well connected

b) Insure palms are in full contact with the sensors

c) Clean palms and keep them from being too dry

3. Motor is not able to be started

a) Check whether all the cables are well connected

b) C

heck whether there is any Error Code displayed on screen

4. Screen is not sensitive to touch

a) Check whether there is water on the screen

b) Check whether there is water on the fingers

1. Error Code "01": Signal communication failure

a) 01:The communication between the computer and the PCB failed.

b) Solution: Check the computer board for any abnormality of the computer chips. Check the connection

between computer and PCB and replace broken connection cable.

2. Error Code "02": Explosion-proof Protection

a) 02: PCB is not able to detect the voltage on motor.

b) Solution: Check whether the power supply voltage is less than 50% of the normal value; please ensure

correct voltage and test again; check whether the PCB emits the odor of burning; if yes, replace the PCB;

check whether motor cables are well connected; re-connect them if any damage

3. E

rror Code "03": No speed sensor signal

a) 03: If speed sensor signal is not received for more than 3s by the PCB;

b) Solution: Check whether the sensor connector is well plugged or whether it is damaged;

plug it well or replace the sensor.

4. Error Code "05": Over-current protection

a) 05: System self-protection is triggered under excessive current caused by the excessive load more

than the rated value, or some place of the treadmill is jammed so that the motor can not rotate; thus,

the system start up self-protection against excessive current under excessive load;

b) Solution: Adjust the treadmill and restart it. Besides, check whether there is over-current sound or burning odor

when the motor is running; replace the motor; check whether the PCB emits abnormal odor;

replace it if yes; check whether power supply voltage specifications is inconsistent

or too low and use correct voltage specifications for re-test.

5. S

afety Lock Off

a) Safety Lock Off: Control board has no singal from Safety Lock

b) Check whether magnetic tube is broken or it's properly placed; check whether magnet is properly placed

B. Other problems and solutions

6.

To display on the computer:

a) Check whether the power cable is well connected; check whether the switch is on; check whether the fuse

Storage

A dry and clean environment is ideal for storage of the treadmill. Make sure the power switch is off

and the cable disconnect from the power outlet.

Page is loading ...

warranty

Fill in the following ﬁeld, to register your device for the warranty.

device-information:

product name/model:

serial number:

purchase date:

invoice number:

personal information:

forname/last name:

street :

city code/city:

country:

E-Mail:

phone number*:

*voluntary information, the remaining ﬁelds are required and must be ﬁlled out.

I have read the warranty conditions and product speciﬁc operation/maintance instructions and accept

them with my signature. For warratny purposes I agree with the savinng of my personal data.

The warranty conditions can be viewed at: www.sportstech.de/garantie

signature

date

city

Send the ﬁlled out warranty card by letter* to the following address:

InnovaMaxx GmbH, Potsdamer Str. 144, D-10783 Berlin

* sufﬁcient postage necessary - letters without sufﬁcient postage cannot be accepted

InnovaMaxx GmbH

Potsdamer Str. 144

D-10783 Berlin

SPORTSTECH F38

phone: +49 (0)30 364 28 66 28

fax: +49 (0)30 364 28 66 01

Email: [email protected]

EC Declaration of Conformity

InnovaMaxx GmbH

Potsdamer Str. 144

10783 Berlin

Germany

We, InnovaMaxx GmbH, explaining that the model described below

Sportstech F38 Laufband

all the relevant requirements of the EC Machinery Directive 2006/42/EC, the EC

Electromagnetic Compatibility Directive 2014/30/EU and the Low Voltage Directive

2014/35/EU.

The audit was carried out by:

Extracted harmonized standards applied:

EN ISO 12100:2010,

EN 60204-1:2006+A1:2009+AC:2010,

EN 957-1:2005, EN 957-6:2010,

EN 55014-1:2006+A1:2009+A2:2011,

EN 61000-3-2:2014, EN 61000-3-3:2013,

EN 55014-2:2015

For the compilation of the technical documentation is

authorized: InnovaMaxx GmbH.

Ali Ahmad, CEO

______________________________

Ber

lin, 22

.04.2016

Ente Certificazione Macchine Srl

Via Ca’ Bella, 243 Loc. Castello di Serravalle

40053 Valsamoggia (BO)

ITALY

Page is loading ...

EC Declaration of Conformity

InnovaMaxx GmbH

Potsdamer Str. 144

10783 Berlin

Germany

We, InnovaMaxx GmbH, explaining that the model described below

Sportstech F38 Laufband

all the relevant requirements of the EC Machinery Directive 2006/42/EC, the EC

Electromagnetic Compatibility Directive 2014/30/EU and the Low Voltage Directive

2014/35/EU.

The audit was carried out by:

Extracted harmonized standards applied:

EN ISO 12100:2010,

EN 60204-1:2006+A1:2009+AC:2010,

EN 957-1:2005, EN 957-6:2010,

EN 55014-1:2006+A1:2009+A2:2011,

EN 61000-3-2:2014, EN 61000-3-3:2013,

EN 55014-2:2015

For the compilation of the technical documentation is

authorized: InnovaMaxx GmbH.

Ali Ahmad, CEO

______________________________

Ber

lin, 22

.04.2016

Ente Certificazione Macchine Srl

Via Ca’ Bella, 243 Loc. Castello di Serravalle

40053 Valsamoggia (BO)

ITALY

Page is loading ...

EC Declaration of Conformity

InnovaMaxx GmbH

Potsdamer Str. 144

10783 Berlin

Germany

We, InnovaMaxx GmbH, explaining that the model described below

Sportstech F38 Laufband

all the relevant requirements of the EC Machinery Directive 2006/42/EC, the EC

Electromagnetic Compatibility Directive 2014/30/EU and the Low Voltage Directive

2014/35/EU.

The audit was carried out by:

Extracted harmonized standards applied:

EN ISO 12100:2010,

EN 60204-1:2006+A1:2009+AC:2010,

EN 957-1:2005, EN 957-6:2010,

EN 55014-1:2006+A1:2009+A2:2011,

EN 61000-3-2:2014, EN 61000-3-3:2013,

EN 55014-2:2015

For the compilation of the technical documentation is

authorized: InnovaMaxx GmbH.

Ali Ahmad, CEO

______________________________

Ber

lin, 22

.04.2016

Ente Certificazione Macchine Srl

Via Ca’ Bella, 243 Loc. Castello di Serravalle

40053 Valsamoggia (BO)

ITALY

Page is loading ...

SPORTSTECH F38 User manual

SPORTSTECH F38 User manual

in other languages

Related papers

Other documents