ClearSounds v407 User manual

CST25

Sound-enhanced

Speakerphone with CALLER ID

Installation Guide & User Manual

Table of Contents

SETTING UP AND INSTALLING YOUR PHONE ................................................. 1

Introduction ......................................................................................................... 1

Important Safety Instructions .............................................................................. 1

Parts Checklist .................................................................................................... 2

Installation .......................................................................................................... 4

Wall Mounting ..................................................................................................... 6

Adjusting the Display Angle ................................................................................ 6

Adjusting the Display Contrast ........................................................................... 6

Adjusting Handset Receiver Volume .................................................................. 6

Adjusting Speakerphone Receiver Volume ........................................................ 7

USING THE TELEPHONE ..................................................................................... 8

Making a Call ...................................................................................................... 8

Editing Telephone Number before Dialing ......................................................... 8

Receiving a Call .................................................................................................. 8

Receiving a Call Waiting Call ............................................................................. 8

Switching Between the Handset and the Speakerphone ................................... 9

Redialing ............................................................................................................. 9

Putting a Call on Hold ......................................................................................... 9

Muting a Call ....................................................................................................... 9

Storing a New Number and Name in the Memory Buttons .............................. 10

Copying the Caller’s Number and Name to a Memory Button ......................... 10

CALLER ID .......................................................................................................... 11

CALLER ID Service and Call Waiting CALLER ID Service .............................. 11

CALLER ID Display .......................................................................................... 11

New Calls and Total Calls ................................................................................ 11

Viewing the CALLER ID List ............................................................................. 12

Calling Back a Number From the CALLER ID List ........................................... 12

Deleting a Call From the CALLER ID List ........................................................ 12

Deleting All Calls from the CALLER ID List ...................................................... 13

Using Call Waiting CALLER ID ........................................................................ 13

Message Indication ........................................................................................... 13

Accessing Voice Mailbox .................................................................................. 13

Clearing the Message Waiting Indicator .......................................................... 13

UNAVAILABLE, PRIVATE CALL and ERROR Messages ............................... 14

IN CASE OF DIFFICULTY ................................................................................... 15

Resetting Your Telephone's Programming ...................................................... 15

Maintenance Information .................................................................................. 15

Troubleshooting ................................................................................................ 16

LIMITED WARRANTY ......................................................................................... 16

Warranty Limitation ........................................................................................... 17

What This Warranty Does Not Cover ............................................................... 17

State Law Rights .............................................................................................. 17

FCC REGISTRATION AND REPAIR INFORMATION ....................................... 18

Connection and Use with the Nationwide Telephone Network ........................ 18

Notification to the Telephone Company ........................................................... 18

Repair Instructions ............................................................................................ 18

Rights of the Telephone Company ................................................................... 18

Interference Information: Part 15 of FCC Rules .............................................. 18

Page 1

Setting Up and Installing Your Phone

Introduction

Congratulations on the purchase of your new telephone. It has been manufactured to very

high quality standards for convenient and reliable service. This telephone can be used

with "Call Identification (CALLER ID) Service" and/or "Call Waiting CALLER ID Service"

that is provided by your local telephone company. There is a fee for these services by

your local telephone company, and they may not be available in all areas. When used

with these services, your telephone displays the telephone number or the telephone

number and name of each caller before you answer the call allowing you to screen your

calls.

In addition to CALLER ID services, if you subscribe to voice mail services from your local

telephone company, voice mail waiting indicators will inform you there is a message

waiting in your voice mailbox.

Important Safety Instructions

Before using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of fire, electric shock and injury to persons, including the

following:

1.

Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the telephone jack and the power outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

4.

Do not use this product near water, such as near a bathtub, sink, laundry tub, in a

wet basement, or near a swimming pool.

5. Do not place this product on an unstable cart, stand, or table. Serious damage may

result if the product falls.

6. Slots or openings in the cabinet and the back and bottom are provided for ventilation

to protect the phone from overheating. These openings must not be blocked or

covered. The product should never be placed near or over a radiator or heat register.

7. This product should be operated only from the type of power source indicated on the

marking label.

8. Do not allow anything to rest on the power cord. Do not locate this product where

the cord will be abused by persons walking on it. Do not attach the power cord to

building surfaces.

9. Do not overload wall outlets and extension cords as this can result in the risk of fire

or electric shock.

10. Never push any objects into this product through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in a fire or electric

shock. Never spill liquid of any kind on the product.

11. If this product does not operate normally, see the “In Case of Difficulty” section in

this owner's manual. If you cannot resolve the problem, or if the product is

damaged, refer to the "Limited Warranty" section of this owner's manual. Opening

the product or reassembling it incorrectly may expose you to dangerous voltages or

other risks, and will void the warranty.

Page 2

12. Unplug this product from the wall outlet and refer servicing to qualified service

personnel under the following conditions: (a) When the power supply cord or plug is

damaged or frayed. (b) If liquid has been spilled into the product. (c) If the product

has been exposed to rain or water. (d) If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by

the operating instructions. (e) If the product has been dropped or the cabinet has

been damaged. (f) If the product exhibits a distinct change in performance.

13. Avoid using a telephone during an electrical storm. There may be a remote risk of

electric shock and/or hearing damage from lightning.

14.

Do not use the telephone near a gas leak even to report the leak.

Parts Checklist

Remember to save your sales receipt in case you ever need warranty service.

Check to make sure your package includes the items described below:

1. Telephone Base 4. AC/DC Adapter

2. Telephone Handset 5. Handset Cord

3. Telephone Line Cord

Make sure you have a modular wall jack near the place you have chosen to install the

telephone. If you have an older phone jack, you will need to buy a modular jack adapter.

Page 3

Controls and Functions

1. LCD display

2. Message light - Visual message waiting indicator.

3. ◑ button – to adjust LCD contrast.

4. Flash button – during a call, to access telco’s calling features.

5. Pause button – to insert 3 seconds delay during memory button programming.

6. Save – to begin programming of memory buttons.

7. Vol. up button – to increase receiver volume for handset and speakerphone.

8. Overlay paper

9. M1 – programmable memory button

10. M2 – programmable memory button

11. M3 – programmable memory button

12. Spk. Button with indicator – to activate or to deactivate speakerphone.

13. Redial button – to redial last number.

14. Vol. down Button – to reduce receiver volume for handset and speakerphone.

Page 4

#00

SELECT LANGUAGE

1 2 3

>ENG ESP FRA

15. Hold with indicator – to put a call on hold, LCD will display “Hold”

16. Mute with indicator – to mute transmitter, LCD will display “Mic Muted”

17. Visual ringer and speakerphone indicators

18. Telephone keypad

19.  - to review upward from the oldest CALLER ID record.

20.  - to review downward from the newest CALLER ID record.

21. Delete button – to delete one or all CALLER ID records, or Message light.

22. Dial button – to dial number displayed or to accept entry

23. Index card

24. Handset tab

25. Hook switch

Installation

1. Plug one end of the flat telephone line

cord into the line jack on the back of the

phone where it is labeled "TEL.LINE"

and plug the other end into your modular

telephone wall jack.

2. Connect one end of the coiled Handset

Cord to the jack on the left side of the

phone and connect the other end of the

coiled Handset Cord to the jack on the

handset

3. Connect the AC adapter to an electrical wall outlet and then connect the AC adapter

plug to the “DC 9V” jack on the back of the phone. Use only with a Class 2 power

source, plug polarity, 9V DC, AC adapter.

4. Selecting a language

When the phone is powered up for the first time, the

display flashes “SELECT LANUGAGE” and “>ENG

ESP FRA”.

To select English, press the “1” button.

To select Spanish, press the “2”

button.

To select France, press the “3”

button.

Then, press the Dial button to confirm the selection.

Page 5

#00

_ _ _

ENTER AREA CODE

7 DIGITS DIAL

#00

3 0 3

ENTER AREA CODE

7 DIGITS DIAL

#00

_ _ _ - _ _ _ - _ _ _

ENTER AREA CODE

10 DIGITS DIAL

#00

7 2 0

ENTER AREA CODE

10 DIGITS DIAL

5. Program your area code

(A) After selecting the language, the display flashes "ENTER AREA CODE" and “7

DIGITS DIAL”.

(B) If you dial your local calls using 7 digits (e.g., 555-

1212), then enter your local area code, press the

Dial button, and go to Step C.

If you dial your local calls using 10 digits (e.g., 303-

555-1212), then enter “000” as the area code for 7

digits dial, and press the Dial button to go to Step C.

(C) The display flashes “ENTER AREA CODE” and “10

DIGITS DIAL”.

Enter the area code(s) for numbers that you dial

using ten digits (e.g., 720-555-1234). You can store

up to three area codes for ten-digit dialing. Press

Dial when you are done. If there is no number you

dial using ten digits, then press Dial.

6. Press the Save button to save these operating settings.

After installation, lift the telephone's Handset and listen for

the dial tone. If there is no dial tone, check to make sure all

cords are firmly plugged into their jacks.

Note: Programming your area code will allow you to easily

dial numbers that are in your CALLER ID list. See the Section “Calling Back a Number

from the CALLER ID List” for more information on dialing calls from your CALLER ID list.

Page 6

Wall Mounting

1. Turn the phone over so that you are looking at the bottom of the phone. Insert tabs at

the thin end of the wall mount bracket into the holes at the

rear of the phone bottom. Press and latch the tabs at the

thicker end of the wall bracket into holes at the front end of

phone. The back of the phone should then have two round

plastic holes that can be used to hang your phone on the

wall.

2. Use the two round holes to hang the phone on the wall plate on your wall.

Important Note: If you do not wish to mount your phone on the wall, the Wall Mount

Bracket can be reversed to raise the angle of the phone's display when sitting on a table

or desk.

Adjusting the Display Angle

You can optimize the LCD display by adjusting the viewing angle. To adjust the LCD

viewing angle, move the rear edge of the LCD module up or down.

Adjusting the Display Contrast

The display can be adjusted to suit the light level of your room and your viewing

preference. To make the contrast of the display lighter or darker, press the ◑ button to

the right of the screen until the desired contrast is reached.

Adjusting Handset Receiver Volume

To adjust the handset receiver volume:

1. Lift the handset and listen to the dial tone.

2. Press the Volume up button to increase the receiver volume.

3. Press the Volume down button to decrease the receiver volume.

4. Replace the handset when the desired receiver volume is reached.

Page 7

Adjusting Speakerphone Receiver Volume

To adjust the speakerphone receiver volume:

1. Press the Speaker button and listen to the dial tone.

2. Press the Volume up button to increase the receiver volume.

3. Press the Volume down button to decrease the receiver volume.

4. Press the Speaker button when the desired receiver volume is reached.

Page 8

Using the Telephone

Making a Call

1. Pick up the Handset or press the Speaker button, and listen for a dial tone.

2. Using the Keypad, dial the desired telephone number. The number you are dialing

will appear on the display as you dial. When making a call or talking on the phone,

the "In Use" light will turn on indicating the phone is in use. This light will also be on

whenever another phone on the same phone line is in use.

Editing Telephone Number before Dialing

You can enter the telephone number you wish to dial before lifting handset or pressing the

Speaker button.

1. Use the keypad to enter the telephone number. The number is displayed on the

screen.

2. If you enter one or more wrong digits, press the delete button one or more times till

incorrect digits are erased.

When all digits of a telephone number are entered correctly, press the Dial button. The

speakerphone is activated and the telephone number is dialed automatically. If you desire

to use the handset instead of the speakerphone simply pickup the handset after pressing

the Dial button.

Receiving a Call

1. When you hear the phone ring, simply pick up the handset from the handset cradle.

You may also press the Speaker button to answer the call using the speakerphone.

2. When you are finished talking, replace the handset in the handset cradle to end the

call. If you have been talking using the speakerphone, press the Speaker button to

hang up.

Receiving a Call Waiting Call

If you subscribe to call waiting services and are on a call when another caller calls your

phone number, you will hear a "beep" indicating there is another call coming in. If you

subscribe to Call Waiting ID services, the caller’s name and number can be displayed on

the screen. To answer the waiting call and/or switch between calls:

1. Press and release the Flash button to put the current call on "hold" and to answer the

incoming call. To switch back and forth between the two calls, press and release the

Flash button.

2. When a Call Waiting call comes in, you may also hang up the current call in order to

pick up the waiting call. When you are on a call you want to end and another call

comes in, hang up the telephone. The current call will be disconnected and after a

temporary delay, the phone will ring, allowing you to answer the waiting call.

Page 9

Switching Between the Handset and the Speakerphone

To switch a call between the Handset and the Speakerphone during a conversation:

1. While talking on the handset, press the Speaker button to activate the speakerphone.

The call can now be heard from the speakerphone.

2. While talking on the speakerphone, simply lift up the handset and the call will be

transferred to the handset and will no longer be heard on the speakerphone.

3. Hang up the handset. Hanging up the handset will not

disconnect the call when the

Speakerphone is activated. You have to press the Speaker button to disconnect the

call.

4. If the speakerphone is not activated, simply hang up the handset and the call will be

disconnected.

Redialing

You can redial the last number you called with just one touch of the Redial button. This

lets you easily redial the same number again if the line was busy.

1. Pick up the handset or press the Speaker button and listen for a dial tone.

2. Press the Redial button and the last number you dialed will be shown on the display

and will be automatically dialed.

Putting a Call on Hold

The Hold button allows you to place a call on "HOLD" without disconnecting the call.

When a call is on hold, you may hang up the handset without disconnecting the call.

1. Press the Hold button and the current call will be placed on hold. If you were talking

with the handset, you can then place the handset back in the handset cradle without

disconnecting the call. If you were talking with the speakerphone, the call is placed on

hold.

2. To continue the conversation, pick up the handset or press the Speaker button.

Muting a Call

In addition to putting a call on hold, muting a call is a good way to mute the phone so that

the person on the other end of the line will not hear what you are saying. You can

continue to hear the person on the other end.

1. Press the Mute button to mute the call.

2. To release the mute, press the Mute button again and you will be able to continue the

conversation. Do not hang up the phone while a call is muted or the call will be

disconnected.

Page 10

#25

800-965-9043

ClearSounds

SAVE TO?

#00

ENTER NUMBER>

#00

8009659043

USE SAVE TO END

SAVE TO?

Storing a New Number and Name in the Memory Buttons

To store a new number and name in the memory

buttons:

1. Press the Save button when the display shows no

caller’s number or name. The “SAVE TO?” prompt

appears on the display.

2. Press the memory button where you wish to store

this telephone number (e.g., M1). The “ENTER

NUMBER>“ prompt appears on the display.

3. Use the keypad to enter the telephone number,

including the long distance prefix that you need to

dial this number. Insert a pause or multiple pauses

where required by using the Pause button. Then

press the Save button.

4. The display will read “PROGRAMMING OK!”.

Copying the Caller’s Number and Name to a Memory Button

When the caller’s number and name you wish to store in a

memory button is displayed during CALLER ID review,

press the Save button. The 3

rd

line of the display indicates

“SAVE TO?”.

You can save this caller’s number and name into a memory

button by pressing the desired memory button (e.g., M1).

The display will read “PROGRAMMING OK!”.

Page 11

10:30am 8/11 #20

800.965.9043

10:30am 8/16 #60

800.965.9043

ClearSounds

25

NEW CALLERS

CALLER ID

CALLER ID Service and Call Waiting CALLER ID Service

The "CALLER Identification" service (CALLER ID) allows the caller’s phone number and/or

name to be shown on the display as the call comes in before you pick up the phone. In

order to use this feature, YOU MUST FIRST SUBSCRIBE TO THE CALLER ID SERVICE

provided by your local telephone company. The name of this service may vary depending

on your telephone company. Before using this feature, please make sure you have

properly entered your area code as explained in the “Programming Your Area Code” step

of the Introduction section of this manual.

Important Note: When a new call comes in, you must let your phone ring at least 2 full

times in order for the CALLER ID information to be displayed.

The Call Waiting CALLER ID service allows the phone number and/or name of a waiting

caller to be shown during a telephone conversation. To use this feature, YOU MUST

FIRST SUBSCRIBE TO CALL WAITING CALLER ID SERVICE with your local telephone

company. The name of this service may vary depending on your telephone company.

CALLER ID Display

When you receive a call, the phone number appears on

the display with the day and time the call was received

and is then stored in the Call Memory as shown.

If your CALLER ID service includes the caller's name,

then the caller’s name also appears on the display (up to

15 letters) as shown.

The date and time information is received from your

telephone company. If the call came from a different

time zone, it will still show the time in your area.

The total number of calls that are saved in the Call Memory is displayed after the “#”

symbol when a call is received. Each call is assigned a call number. The most recent call

has the highest number (e.g. “#99”) and the oldest call has the smallest number (e.g. “

#1”). The phone number of a waiting caller is also registered into the Call Memory as

another call.

New Calls and Total Calls

When the phone is not in use, the display indicates the

number of new calls that have been received since the

last review of the Call Memory as well as the total

number of calls in memory.

Page 12

#80

END OF RECORD

#61

DELETED

Viewing the CALLER ID List

This CALLER ID telephone automatically stores in the

Call Memory the CALLER ID information of the last 99

calls received. It keeps track of all calls received,

whether they were answered or not. The oldest call in

the Call Memory is always call #1. The highest

numbered call (or call #99 if the Call Memory is full) is always the most recent call. If the

Call Memory is full with 99 calls and a new call comes in, the oldest call, call #1, is

automatically deleted to make room in the memory for the new call.

1. Press the ▼ button to display the most recent call and to move backward through the

call records.

2. Press the ▲ button to display the oldest call and to move forward through the call

records.

3. When you get to the last call stored in the Call Memory, then the “END OF

RECORD” message will appear on the display. If the screen indicates "END OF

RECORD", press the ▲ button and the screen will display the first record in the Call

Memory. If you press the ▼ button, the screen will display the last record in the Call

Memory.

Important Note: The telephone's buttons will not work while the phone is ringing, or for a

few seconds afterward.

Calling Back a Number From the CALLER ID List

To easily call back a number from the CALLER ID list:

1. Press the ▼ button or the ▲ button until the number you want to call is displayed.

2. Press the Dial button. The number is dialed automatically.

The area code is not dialed when it matches the area code stored for 7 DIGITS DIAL. The

area code is dialed for all other numbers. When the area code matches any area code

stored for 10 DIGITS DIAL, then the number is dialed as a ten-digit call (e.g., 303-555-

1212). When the area code does not match an area code for 10 DIGITS DIAL, the number

is dialed as a long distance call (e.g., 1-520-555-1234).

Deleting a Call From the CALLER ID List

Important Note: Be sure to write down on a piece of paper any important phone numbers

or information before deleting them from the Call Memory.

1. Press the ▼ button or the ▲ button until the call

information you want to erase is displayed on the

screen.

2. Press the Delete button once and the selected call is

erased from the Call Memory. The display shows

"DELETED".

Page 13

10:30am 8/16 #61WAITING

800.965.9043

ClearSounds

#61

48

NEW CALLERS

MESSAGES

#00

DEL ALL!

Deleting All Calls from the CALLER ID List

To delete all the calls stored in Call Memory at once,

press and hold the Delete button for 5 seconds. The

entire list of calls will be completely cleared and the

display shows "DEL ALL!”. .

Using Call Waiting CALLER ID

If another call comes in during a conversation, your phone will display the "WAITING"

message in the upper right hand corner and the incoming caller's information will be

displayed on the screen. To pick up the waiting call:

1. Press and release the Flash button to put the

current call on "hold" and to answer the incoming

call. To switch back and forth between the two calls,

press and release the Flash button.

2. When a Call Waiting call comes in, you may also hang up the current call in order to

pick up the waiting call. The current call will be disconnected and after a temporary

delay, the phone will ring, allowing you to answer the waiting call.

Message Indication

The Message indicator flashes to indicate a message(s) is in your local telephone

company’s voice mailbox, if you subscribe to voice mailbox

services and your local telephone company delivers a

"Visual Voice Message Waiting Indication Signal".

When you have messages waiting in your voice mailbox,

the screen will display “MESSAGES” and “NEW

CALLERS” alternatively, and an envelope-shaped Voice

Mail Waiting icon "  " will flash.

Accessing Voice Mailbox

Please follow instructions from your voice mail service provider to access your voice

mailbox.

Clearing the Message Waiting Indicator

If you have Voice Messaging service (Voice Mail), whenever you have a new message the

display will show “MESSAGES” and the red light labeled Message will flash. After you

Page 14

2:00pm 8/15 #42

_ _ _ _ _ _ _ _ _ _ _ _

UNAVAILABLE

2:05pm 8/15 #43

_ _ _ _ _ _ _ _ _ _ _ _

PRIVATE CALL

#44

_ _ _ _ _ _ _ _ _ _ _ _

ERROR

listen to your new message, the message waiting indicators will turn off automatically after

a short delay. If these indicators remain on even after you have listened to all your

messages, you can manually clear the indicators by pressing the Delete button when

“MESSAGES” and “NEW CALLERS” are displayed on LCD, alternatively.

UNAVAILABLE, PRIVATE CALL and ERROR Messages

Certain messages may appear instead of a caller's name and/or number:

1. The screen will display "UNAVAILABLE" if a call is

made through a telephone company which does not

offer the CALLER ID service. This can include long

distance, international, and sometimes even local

phone calls.

2. The screen will display "PRIVATE CALL" if a caller's

information is blocked from being transmitted. For

privacy reasons, many states allow callers the ability

to block his or her telephone information from being

displayed on another person's CALLER ID display.

3. The screen will display “ERROR” if the caller’s

information being transmitted to your telephone is

corrupt or contains some errors from the

transmission process.

Page 15

In Case of Difficulty

Resetting Your Telephone's Programming

Electrostatic or power surge (e.g., from lightning) may cause the phone to lock up. There

are two ways to reset this phone.

1. Basic reset

• Disconnect the telephone line cord from the phone.

• Disconnect the AC adapter from the phone.

• Press the ▼ button or the ▲ button two times. Wait for 10 seconds;

• Reconnect the telephone line cord and the AC adapter to the phone.

• Follow the installation procedures to select the language and to enter the

area codes.

2. Full reset

If the basic reset cannot return to the phone to the normal operating condition, you

must do a full reset. All information stored in memory will be erased during a full

reset.

• Disconnect the telephone line cord from the phone.

• Disconnect the AC adapter from the phone.

• Press the ▼ button or the ▲ button two times. Wait for 10 seconds.

• Press and hold the Delete button and the ▲ buttons when reconnecting the

AC adapter to the phone.

• Reconnect the telephone line cord.

• Follow the Installation procedures to select the language and to enter the

area codes.

Maintenance Information

Although your unit is designed to be maintenance free, it contains sensitive electronic

parts. Treat it with care to assure the best performance.

Avoid Rough Treatment: Avoid dropping the unit. The original packaging should be used

for protection if you must ship the unit. Dropping or damaging the unit will void the

warranty.

Cleaning: The hard plastic casing on your unit has a durable finish that should retain its

original luster for many years. Clean exposed parts with a soft, slightly damp cloth. To

remove stains, use a mild soap. Never use detergents, excess water, treated cloths,

harsh cleaning agents, or sprays.

Page 16

Troubleshooting

If your product does not work properly, try the following suggestions before seeking repair

assistance:

• Check all line cord connections at the wall jack and at the telephone.

• "CALLER Identification" is a subscription service. Non-subscribers of this

service cannot receive CALLER Identification information. Make sure that

the telephone company has activated your service.

• The telephone receives call information between the first and second ring. If

the caller hangs up or you answer before the second ring, the telephone may

not receive the call Identification information.

• If you have Call Forwarding Service and your calls are forwarded, the

telephone will not receive the caller's information. Calls forwarded using a

call forwarding service are typically forwarded before completing the second

ring. To receive a caller's information, turn off the Call Forwarding feature.

Important Note: Make sure you have followed all the instructions in this booklet. If you

continue to have problems, call (USA) ClearSounds Customer Service at (800) 965.9043,

(Canada) ClearSounds Canada at (604) 980-6686.

Limited Warranty

This warranty applies only to products purchased and used in the United States.

What Is Covered? Any defect in materials or workmanship.

For How Long? For one year from the date of purchase

What We Will Do: If we repair your product, we may use new or reconditioned

replacement parts. If we choose to replace your product, we may replace it with a new or

reconditioned one of the same or similar design. The repair or replacement product will be

warranted for either (a) 90 days or (b) the remainder of the original one year warranty

period, whichever is longer.

Page 17

What We Ask You To Do: You must prepay all shipping and handling costs. We

suggest you retain your original packing material in the event you need to ship your

product. When sending your product for repair service, include your name, address,

telephone number with area code, proof of date of purchase, prepaid shipping and

handling costs, and a description of the problem. Send all of this to:

ClearSounds USA

Attn: Repair Center

ClearSounds Canada

Attn: Repair Center

8160 S. Madison St 110-1861 Welch Street

Burr Ridge, IL 60527

North Vancouver, BC V7P 1B7

.

Warranty Limitation

Implied warranties, including those of fitness for a particular purpose and merchantability

(an unwritten warranty that the product is fit for ordinary use), are limited to one year from

date of purchase. We will not pay for loss of time, inconvenience, loss of use of your

product, or property damage caused by your product or its failure to work, or any other

incidental or consequential damages. Some states do not allow limitations on how long an

implied warranty lasts or the exclusion or limitation of incidental or consequential

damages, so the above exclusions or limitations may not apply to you.

What This Warranty Does Not Cover

This warranty does not cover defects resulting from accidents, damage while in-transit to

or from our Product Service Center, alterations, unauthorized repair, failure to follow

instructions, misuse, use outside the United States and Canada, fire, flood, and acts of

God. We do not warrant your product to be compatible with any particular telephone

equipment or party line, key telephone systems or more sophisticated customer premises

switching systems. If your product is not covered by our warranty, call us for advice as to

whether we will repair your product and other warranty repair information, including

required shipping and handling charges. We, at our option, may replace rather than repair

your product with a new or reconditioned product of the same or similar design. The repair

or replacement product will be warranted for either (a) 90 days or (b) the remainder of the

original one year warranty period, whichever is longer.

State Law Rights

This warranty gives you specific legal rights, and you may also have other rights that vary

from state to state.

Page is loading ...

ClearSounds v407 User manual

This manual is also suitable for

ClearSounds v407 User manual

in other languages

Related papers

Other documents