Panasonic KX-TG5230C Operating Instructions Manual

Brand: Panasonic

Model: KX-TG5230C

Category: Telephones

Type: Operating Instructions Manual

5.8 GHz Expandable Cordless Phone System

Operating Instructions

Model No. KX-TG5230C

Pulse-or-tone dialing capability

This unit is Call Display compatible. To display the caller’s name and phone

number, you must subscribe to Call Display service.

PLEASE READ BEFORE USE AND SAVE.

For assistance, please call 1-800-561-5505 or visit us at www.panasonic.ca

Charge the battery for 6 hours before initial use.

TG5230C_English.fm Page 1 Tuesday, May 11, 2004 9:08 AM

Thank you for purchasing your new Panasonic cordless

telephone.

Accessories (included)

Call Display, Call Waiting and Voice Mail service, where available, are telephone

company services. After subscribing to Call Display this phone will display a

caller’s name and phone number. Visual Call Waiting/Call Waiting Deluxe, which

displays a second caller’s name and phone number while the user is on another

call, requires a subscription to both Call Display and Visual Call Waiting

services. After subscribing to Voice Mail service, this unit will give you visual

indication to let you know when there are messages in the mailbox.

A AC Adaptor (p. 11)

one

A Telephone Line Cord

(p. 11)

one

A Wall Mounting

Adaptor (p. 64)

one

A Handset Cover (p. 12)

one

A Battery (p. 12)

one

A Belt Clip (p. 63)

one

TG5230C_English.fm Page 2 Tuesday, May 11, 2004 9:08 AM

Expanding Your Phone

KX-TG5230C includes one handset and one base unit. You can expand the system

by adding up to 3 accessory handsets, sold separately.

A maximum of 4 handsets can be registered to the base unit.

The handset included is pre-registered at the factory and assigned the extension

number 1.

After purchasing accessory handsets, you must register each to the base unit.

(Please read the accessory handset’s Installation Manual.)

The model numbers of the accessory handsets are KX-TGA520C and

KX-TGA523C. A charger is included with each accessory handset.

KX-TG5230C

Up to 3 accessory handsets can be added.

The illustration is KX-TGA520C.

TG5230C_English.fm Page 3 Tuesday, May 11, 2004 9:08 AM

Contents

For Best Performance . . . . . . . . 6

Location of Controls . . . . . . . . . 7

Display . . . . . . . . . . . . . . . . . . . 10

Installation . . . . . . . . . . . . . . . . 11

Connections . . . . . . . . . . . . . . 11

Installing the Battery in

the Handset. . . . . . . . . . . . . . . 12

Battery Charge . . . . . . . . . . . . 12

Programmable Settings. . . . . . 14

Programming Guidelines. . . . . 14

Function Menu Table . . . . . . . 15

Display Language

. . . . . . . . . . . 16

Talking Call Display

Language

. . . . . . . . . . . . . . . . . . . 16

Dialing Mode . . . . . . . . . . . . . . 17

Line Mode . . . . . . . . . . . . . . . . 17

Auto Talk . . . . . . . . . . . . . . . . . 18

Ringer Volume . . . . . . . . . . . . 18

Ringer Tone . . . . . . . . . . . . . . 20

LCD Contrast . . . . . . . . . . . . . 22

Message Alert . . . . . . . . . . . . . 22

Making Calls . . . . . . . . . . . . . . . 23

Using the Handset. . . . . . . . . . 23

Using the Base Unit . . . . . . . . 26

Answering Calls . . . . . . . . . . . . 27

Call Display Service . . . . . . . . . 28

Talking Call Display. . . . . . . . . 29

Using the Caller List . . . . . . . . 31

Viewing the Caller List. . . . . . . 31

Calling Back from the

Caller List . . . . . . . . . . . . . . . . 32

Editing the Caller’s Phone

Number . . . . . . . . . . . . . . . . . . 33

Storing Caller Information

in the Phone Book. . . . . . . . . . 34

Erasing Caller Information. . . . 34

Phone Book . . . . . . . . . . . . . . . 35

Storing Names and Numbers

. . . 35

Dialing from the Phone Book

. . 37

Chain Dial

. . . . . . . . . . . . . . . . 38

Editing an Item in the

Phone Book

. . . . . . . . . . . . . . . 39

Erasing an Item in the

Phone Book

. . . . . . . . . . . . . . . 39

Copying Items in the

Phone Book. . . . . . . . . . . . . . . 40

Speed Dialer . . . . . . . . . . . . . . . 42

Storing Phone Numbers . . . . . 42

Dialing a Stored Phone

Number . . . . . . . . . . . . . . . . . . 42

Intercom . . . . . . . . . . . . . . . . . . 43

Making Intercom Calls. . . . . . . 43

Answering Intercom Calls . . . . 44

Voice Paging . . . . . . . . . . . . . . 45

Transferring a Call . . . . . . . . . . 46

Conference Calls . . . . . . . . . . . 49

Call Share . . . . . . . . . . . . . . . . 49

Room Monitor. . . . . . . . . . . . . . 50

Voice Mail Service . . . . . . . . . . 52

Storing a Voice Mail Access

Number . . . . . . . . . . . . . . . . . . 52

Setting Voice Mail (VM) Tone

Detection . . . . . . . . . . . . . . . . . 53

Listening to Voice Mail

Messages . . . . . . . . . . . . . . . . 54

Preparation

Basic Operation

Advanced Operation

TG5230C_English.fm Page 4 Tuesday, May 11, 2004 9:08 AM

Contents

Useful Information

Advanced Operation

Basic Operation

Preparation

Special Features . . . . . . . . . . . . 55

Muting Your Conversation . . . . 55

Call Privacy . . . . . . . . . . . . . . . 55

Using the PAUSE Button

(For PBX Line/Long Distance

Calls) . . . . . . . . . . . . . . . . . . . . 56

For Call Waiting Service

Users . . . . . . . . . . . . . . . . . . . . 56

Call Waiting Deluxe

Service. . . . . . . . . . . . . . . . . . . 57

Temporary Tone Dialing (For

Rotary or Pulse Service Users). . 60

FLASH Button . . . . . . . . . . . . . 60

Incoming Call Tone . . . . . . . . . 61

Key Tone . . . . . . . . . . . . . . . . . 62

Belt Clip . . . . . . . . . . . . . . . . . . . 63

Optional Headset . . . . . . . . . . . 63

Wall Mounting . . . . . . . . . . . . . . 64

Direct Commands . . . . . . . . . . . 67

Cancelling Registration/

Re-registration . . . . . . . . . . . . . 69

Cancelling the Handset

Registration . . . . . . . . . . . . . . . 69

Re-registering the Handset . . . 69

If the Following Appears on

Your Display...

. . . . . . . . . . 71

Important Information . . . . . . . 77

Safety Instructions . . . . . . . . . . 78

Specifications . . . . . . . . . . . . . . 79

Warranty . . . . . . . . . . Back Cover

Useful Information

Troubleshooting . . . . . . . . . . . . 73

Important

Throughout these Operating Instructions, and are used

to indicate with which unit an operation can be performed.

: Perform with the handset.

: Perform with the base unit.

: Perform with the handset and base unit separately.

Perform with

the handset and base unit

together.

Handset Base Unit

Handset

Base Unit

Handset Base Unit

Handset & Base Unit

TG5230C_English.fm Page 5 Tuesday, May 11, 2004 9:08 AM

For Best Performance

Battery charge

The handset is powered by a rechargeable

Nickel-Metal Hydride (Ni-MH) battery. Charge the

battery for 6 hours before initial use (p. 12).

Base unit location/Noise

Calls are transmitted between the base unit and handset using wireless radio

waves. For maximum distance and noise-free operation, the recommended

base unit location is:

Note:

• If you use the handset near a microwave oven which is being used, noise may be

heard from the receiver or the speaker. Move away from the microwave oven and

closer to the base unit.

• If you use the handset near another cordless phone’s base unit, noise may be

heard. Move away from the other cordless phone’s base unit and closer to your

base unit.

way from electrical appliances

such as a TV, personal computer

or another cordless phone.

In a HIGH and CENTRAL location

with no obstructions such as walls.

Raise the

antennas.

TG5230C_English.fm Page 6 Tuesday, May 11, 2004 9:08 AM

Useful InformationAnswering SystemTelephone System

Preparation

Location of Controls

Base unit

TG5230

TG52

Antenna (p. 6)

ntenna

(p. 6)

MIC (Microphone) (p. 26)

[SP-PHONE] (Speakerphone)

Button and Indicator (p. 26)

[HOLD] Button (p. 26)

[CONF] (Conference)

Button (p. 49)

CHARGE Indicator (p. 12)

Charge Contacts (p. 13)

Speaker

Navigator Key

([B], [d], [f], [g]) (p. 9)

[PROGRAM] Button

(p. 42)

[AUTO] Button

(p. 42)

IN USE Indicator (p. 27)

[MUTE] Button (p. 55)

[FLASH/CALL WAIT]

Button (p. 56, 60)

[ ] (TONE) Button (p. 60)

[LOCATOR/

INTERCOM/

TRANSFER]

Button and

Indicator (p. 43)

[REDIAL/PAUSE]

Button (p. 26, 56)

[VM] (Voice Mail)

Button and Indicator

(p. 54)

TG5230C_English.fm Page 7 Tuesday, May 11, 2004 9:08 AM

Location of Controls

Handset

Back side

Speaker

Headset Jack (p. 63)

[MENU]

Button (p. 14)

Microphone (p. 23)

Charge Contacts (p. 13)

Antenna

Display (p. 10)

[OFF] Button (p. 14, 23)

[HOLD/INTERCOM]

Button (p. 24, 43)

[REDIAL] Button (p. 24)

Soft Keys (p. 9)

Receiver

[FLASH/CALL WAIT]

Button

(p. 56, 58, 60)

Navigator Key ([d], [B])

(p. 9)

Ringer/Message Alert

Indicator (p. 22, 27)

[ ]

(

TONE

)

Button (p. 60)

[C] (TALK) Button (p. 23)

[s] (Speakerphone)

Button (p. 23)

TG5230C_English.fm Page 8 Tuesday, May 11, 2004 9:08 AM

Useful InformationAnswering SystemTelephone System

Location of Controls

Preparation

Handset navigator key

Scrolls up [B] and down [d] the function menu, the

Caller List and the phone book.

Increases [B] or decreases [d] the handset ringer and

receiver/speaker volumes.

Base unit navigator key

Increases [B] or decreases [d] the base unit ringer and

speaker volumes.

[f] and [g]

select the base unit ringer tone.

Throughout these Operating Instructions, the soft keys are indicated by their

icons, such as and C.

Throughout these Operating Instructions, the handset navigator key is indicated

by the arrows [d] or [B].

Throughout these Operating Instructions, the base unit navigator key is

indicated by the arrows [d], [B], [f] or [g].

How to use the soft keys/navigator keys

Handset soft keys

Three soft keys are used to select functions

displayed directly above each key. Functions

displayed above each key will change depending on

the state of use.

On this sample display, “

” and “C” are

displayed above the soft keys.

Pressing the right soft key selects the Phone Book “

C ”.

Pressing the left soft key reviews caller information in the Caller List

“

”.

• When a function name does not appear above a soft key, the soft key has no

function.

PRIVACY

IN USE

[

]

CID PLAY

CID

TG5230C_English.fm Page 9 Tuesday, May 11, 2004 9:08 AM

Display

1 “ ” functions as follows.

2 “SP” is shown when you are using the handset speakerphone.

3 “ ” indicates Voice Enhancer mode is on (p. 25).

4 “PRIVACY” indicates Call Privacy mode is on (p. 55). Other extension users

cannot join your conversation.

5 The battery icon indicates battery strength (p. 12).

6 The extension number of your handset is displayed if it has been registered to

the base unit (p. 3, 69, 70).

7 The display shows the dialed number, call status, programming options, phone

book items, caller information, etc.

8 The icons on the bottom line indicate the functions of the corresponding soft

keys which are located directly below the display (p. 9).

e.g. The soft key below “C” (phone book icon) is used when storing or viewing

phone book items (p. 35, 37).

9 “D” (extension icon) and extension numbers are displayed (e.g. base unit=“0”,

handset 1= “1”)

a) during an intercom call (p. 43) or a conference call (p. 49);

b) while monitoring a room (p. 51).

Off (invisible) The line is free.

On The line is being used.

Flashing A call is on hold on the handset or base unit.

Flashing rapidly A call is being received.

PRIVACY

10 missed calls

D01

IN USE

[

]

CID PLAY

1234 56

IN USE

TG5230C_English.fm Page 10 Tuesday, May 11, 2004 9:08 AM

Useful InformationAnswering SystemTelephone System

Preparation

Installation

Connections

•

USE ONLY WITH

Panasonic AC ADAPTOR PQLV1.

• The AC adaptor must remain connected at all times. (It is normal for the adaptor to

feel warm during use.)

• If your unit is connected to a PBX which does not support Call Display and voice

mail services, you cannot access those services.

• This unit will not function during a power failure. We recommend connecting a

standard telephone to the same telephone line or to the same telephone jack

using a T-adaptor.

• If the unit is connected to a telephone line with DSL service, you may hear noise

from the receiver or speaker during conversations or the unit may not display

caller’s name and/or phone number properly. We recommend the addition of a

noise filter (contact your DSL service provider) to the telephone line between the

base unit and the telephone line jack.

1. This option is only for DSL users.

2. The filter will be supplied by the DSL service provider.

Hook

Bottom of the base unit

Fasten the AC adaptor cord.

Single-Line Telephone Jack (CA11A)

AC Adaptor

Power Outlet (AC 120 V, 60 Hz)

Raise the antennas.

Telephone

Line Cord

Noise Filter

(For DSL users)

TG5230C_English.fm Page 11 Tuesday, May 11, 2004 9:08 AM

Installation

Installing the Battery in the Handset

Insert the battery (1) and press it down until it snaps into the compartment (2).

Close the cover.

To replace the battery:

Press the notch on the cover firmly and slide it as

indicated by the arrow. Replace the old battery with a new

one (p. 13). Close the cover and charge the handset for 6

hours.

Battery Charge

Place the handset on the base unit for 6 hours

before initial use. Repeat charging will require

approximately the same amount of charging time (6

hours) if the battery is depleted completely.

• The unit beeps once, the CHARGE indicator lights and

“Charging” is displayed.

• When the battery is fully charged, “Charge

completed” is displayed if there are no new calls in the

Caller List.

Battery strength

You can confirm the battery

strength on the handset

display.

Battery strength is indicated

by the icons shown in the

chart to the right.

Display prompt Battery strength

1 Fully charged

2 Medium

3 Low

(flashing) Needs to be recharged.

4 Discharged

CHARGE Indicato

TG5230C_English.fm Page 12 Tuesday, May 11, 2004 9:08 AM

Useful InformationAnswering SystemTelephone System

Installation

Preparation

Recharge

Recharge the battery when:

— “Recharge battery” is displayed on the handset,

— “

3” flashes, or

— the handset beeps intermittently while it is in use.

• The display will continually indicate “Recharge battery” and/or “

3” will

flash when the handset battery is charged for less than 15 minutes and the

handset is lifted off the base unit.

• If the battery has been discharged, the handset will display “Charge for 6 HRS”

and “

4” when you place the handset on the base unit. The handset will not

work unless the battery is charged. Continue charging.

A nickel metal hydride battery that is recyclable powers the product

you have purchased. Please call 1-800-8-BATTERY for information

on how to recycle this battery.

Battery information

After your Panasonic battery is fully charged, you can expect the following performance:

• A fully charged battery will give you up to 5 hours of continuous talk time, or keep

your handset in Standby mode to receive incoming calls for up to 11 days (if no

phone calls are made). Battery power is consumed whenever the handset is off

the base unit, even when the handset is not in use. The longer you leave the

handset off the base unit, the time you can actually talk on the handset will be

shortened. Actual battery performance depends on a combination of how often

the handset is in TALK mode and how often it is in Standby mode.

• Clean the charge contacts of the handset and the base unit with a soft, dry

cloth once a month. Clean more often if the unit is subject to grease, dust or

high humidity, otherwise, the battery may not charge properly.

• If the battery is fully charged, you do not have to place the handset on the base

unit until “Recharge battery” is displayed and/or “

3” flashes. This will

maximize the battery life.

•

If you want to keep the battery fully charged at all times, place the handset on the

base unit when the handset is not being used. The battery cannot be overcharged.

• When the Clarity Booster feature is turned on automatically or manually, battery

operating time may be shortened (p. 25).

Battery replacement:

If you cleaned the charge contacts and fully charged the battery, but after a few

telephone calls, “Recharge battery” is displayed and/or “3” continues to

flash, or “Charge for 6 HRS” and “

4” are displayed, the battery may need

to be replaced. Please replace with a new Panasonic HHR-P104 battery. To

replace the battery, see page 12.

Operation Operating time

While in use (TALK) Up to 5 hours

While not in use (Standby) Up to 11 days

While using the Clarity Booster feature (p. 25) Up to 3 hours

PRIVACY

Recharge battery

IN USE

[

]

TG5230C_English.fm Page 13 Tuesday, May 11, 2004 9:08 AM

Programmable Settings

Programming Guidelines

This unit has several programmable functions which can be selected from the

function menu on the display (p. 15).

How to select a function item from the menu

• To go back to the previous menu, press the soft key ( ), or press the soft key

( ) while “---(Go back)----” is displayed. If you press this key in the

main menu, the unit will exit programming mode.

• After programming is complete, the display will return to the main menu or the

sub-menu depending on the menu in which the selected item is located. (See the

menu table on page 15.)

• You can exit programming mode at any time by pressing [OFF].

•

If you do not press any button for 60 seconds, the unit will exit programming mode.

• If the unit detects a problem, an error message will be displayed (p. 71–73) and/or

error beeps will sound.

Make sure the handset and base unit are not being used. The handset

must be operated near the base unit and while off the base unit.

Press

[MENU]

• The main menu is displayed (p. 15).

2 Scroll to the desired item by pressing [d] or [B].

3 Press the soft key ( ) to select the desired item.

4 If the item has a sub-menu, select the menu item (p. 15).

Repeat steps 2 and 3 until the desired item is displayed.

If the item has no sub-menu, go to step 5.

5 Select the desired setting by pressing [d] or

[B], then press the soft key ( ).

• A confirmation tone will be heard and the setting

will be saved.

6 Press

[OFF] to exit programming mode.

Handset

SAVE

BACK

SAVE

[OFF] exits

programming.

Navigator key scrolls

through the menu.

[MENU] enters the

function menu.

The soft key works as

the or key.

The soft key works

as the key.

BACK

SAVE

SELECT

Ringer setting

BACK

PLAY

SELECT

SAVE

BACK

PLAY

SAVE

BACK

SELECT

TG5230C_English.fm Page 14 Tuesday, May 11, 2004 9:08 AM

Useful InformationAnswering SystemTelephone System

Programmable Settings

Preparation

Function Menu Table

You can use the following functions to customize your unit. See the corresponding

pages for function details.

• After pressing [MENU], you can also program menu items directly by pressing [0]

to [9], [*] and [#] instead of using the soft keys (p. 67–68).

• If you program the Voice Mail (VM) access number, Voice Mail (VM) tone

detection, dialing mode, flash time, line mode, C.WTG options or voice prompt

using one of the handsets, you will not need to program the same item using

another handset.

Handset

Ringer volume

Ringer tone

Incoming call.

Voice Mail

LCD contrast

Key tone

Auto talk

Room monitor

Registration

HS registration

Deregistration

Message alert

Incoming call.

Room monitor

Talk Caller ID

Ringer tone

Change language

Main menu

Sub-menu

Ringer setting

Voice enhancer

Initial setting

Sub-menu

Copy 1 item

Copy all items

Copy phone book

Talk Caller ID

Store VM access#

VM tone detect

Set tel line

Set base unit

Set flash time

Set line mode

C.WTG options

Set dial mode

Display

Voice prompt

p. 52

p. 53

p. 17

p. 60

p. 17

p. 57

p. 21

p. 61

p. 50

p. 30

p. 70

p. 69

p. 16

p. 18

p. 20

p. 61

p. 40

p. 41

p. 22

p. 62

p. 18

p. 50

p. 25

p. 30

TG5230C_English.fm Page 15 Tuesday, May 11, 2004 9:08 AM

Programmable Settings

Display Language

You can select either “English” or “Français” (French) as the display language. The

factory preset is “English”.

• If you select a language you cannot read, change the display language again

using direct commands (p. 67).

Talking Call Display Language

You can select either “English” or “Français” (French) as the language used for

voice prompts when using the Talking Call Display feature. The factory preset is

“English”.

1 Press [MENU].

2 Scroll to “Initial setting” by pressing

[d] or [B], then press the soft key ( ).

3 Scroll to “Change language” by pressing

[d] or [B], then press the soft key ( ).

4 Press the soft key ( ) at “Display”.

5 To change from English to French, press the

soft key ( ). To change from French to

English, press the soft key ( ).

• The display changes to the selected language.

• You can also select the display language by

pressing [d] or [B].

When French is selected, press the soft key ( ), then press

[OFF]

When English is selected, press the soft key ( ), then press

[OFF]

1 Press [MENU].

2 Scroll to “Initial setting” by pressing [d] or [B], then press the

soft key ( ).

3 Scroll to “Change language” by pressing [d] or [B], then press the

soft key ( ).

4 Scroll to “Voice prompt” by pressing [d] or

[B], then press the soft key ( ).

5 Select “Français” (French) or “English”

by pressing [d] or [B].

• The Talking Call Display language changes to

the selected language.

Press the soft key ( ), then press

[OFF]

Handset

SELECT

Initial setting

SELECT

Change language

SELECT

Display

FRANÇ.

ENGLISH

Display

:English

SAUV

SAVE

Handset

SELECT

Voice prompt

:English

SAVE

TG5230C_English.fm Page 16 Tuesday, May 11, 2004 9:08 AM

Useful InformationAnswering SystemTelephone System

Programmable Settings

Preparation

Dialing Mode

If you have touch tone service, set the dialing mode to “Tone”. For rotary or pulse

service, set to “Pulse”. The factory preset is “Tone”.

Line Mode

The line mode is preset to “B” and generally should not be adjusted. If “

”

not displayed on the handset properly, the line mode selection is incorrect. Set line

mode to

“A”

1 Press [MENU].

2 Scroll to “Initial setting” by pressing

[d] or [B], then press the soft key ( ).

3 Scroll to “Set tel line” by pressing [d] or

[B], then press the soft key ( ).

4 Press the soft key ( ) at “Set dial

mode”.

5 Select “Pulse” or “Tone” by pressing [d] or

[B].

6 Press the soft key ( ), then press [OFF].

1 Press [MENU].

2 Scroll to “Initial setting” by pressing

[d] or [B], then press the soft key ( ).

3 Scroll to “Set tel line” by pressing [d] or

[B], then press the soft key ( ).

4 Scroll to “Set line mode” by pressing [d]

or [B], then press the soft key ( ).

5 Select “A” or “B” by pressing [d] or [B].

6 Press the soft key ( ), then press [OFF].

Handset

SELECT

Initial setting

SELECT

Set tel line

SELECT

Set dial mode

:Tone

SAVE

Handset

IN USE

SELECT

Initial setting

SELECT

Set tel line

SELECT

Set line mode

SAVE

TG5230C_English.fm Page 17 Tuesday, May 11, 2004 9:08 AM

Programmable Settings

Auto Talk

The Auto Talk feature allows you to answer calls by simply lifting the handset off the

base unit (or the charger, for accessory handset users, p. 3). You do not need to

press [C] or [s]. The factory preset is OFF.

• In order to view caller information after you lift the handset to answer a call, leave

the Auto Talk feature turned off.

Ringer Volume

You can set the handset and base unit ringer volumes to high, medium, low, or off.

The factory preset is HIGH. If the handset or base unit ringer is turned off, the

handset or base unit will ring at the low level for intercom calls, and will not ring for

outside calls. Caller names will not be announced even if the Talking Call Display

feature is turned on (p. 30).

Handset ringer volume

1 Press [MENU].

2 Scroll to “Initial setting” by pressing

[d] or [B], then press the soft key ( ).

3 Scroll to “Auto talk” by pressing [d] or

[B], then press the soft key ( ).

4 Select “On” or “Off” by pressing [d] or [B].

5 Press the soft key ( ), then press [OFF].

Press

[MENU]

2 Press the soft key ( ) at “Ringer

setting”.

3 Press the soft key ( ) at “Ringer

volume”.

4 Select the desired volume by pressing [d] or

[B].

• The volume will change and ring.

• The number of steps indicates the volume level.

• To turn the ringer off, press [d] repeatedly until

“Off ?” is displayed.

Handset

SELECT

Initial setting

SELECT

Auto talk

:Off

SAVE

Handset

SELECT

Ringer setting

SELECT

Ringer volume

Low High

e.g. High

Ringer volume

Off ?

e.g. Off

TG5230C_English.fm Page 18 Tuesday, May 11, 2004 9:08 AM

Useful InformationAnswering SystemTelephone System

Programmable Settings

Preparation

• If the handset ringer is turned off, the handset displays “Ringer off” while not in

use. When there are new messages in your voice mailbox (p. 54), “Ringer off”

is not displayed.

•

You can also adjust the ringer volume while an outside call is ringing. Press

[d]

[B]

while the handset is ringing.

Temporary ringer off

While the handset is ringing for an outside call, you can turn the ringer off

temporarily by pressing [OFF]. The handset will ring again as usual the next time a

call is received.

Base unit ringer volume

Make sure the base unit is not being used.

To set the ringer volume to high (preset), medium, or low,

press

[

]

[

]

• To increase volume, press [B]. To decrease volume, press [d]

• To stop ringing, press [0].

To turn the ringer off, press and hold [d] until 2 beeps sound.

To turn the ringer on, press [d] or [B].

• The base unit will ring at the low level.

• You can adjust the ringer volume while an outside call is ringing.

Press

[d] or [B] while the base unit is ringing.

To turn the ringer off, press and hold [d] until 2 beeps sound.

5 Press the soft key ( ).

SAVE

Base Unit

TG5230C_English.fm Page 19 Tuesday, May 11, 2004 9:08 AM

Programmable Settings

Ringer Tone

You can set the handset and base unit ringers to use one of 7 ringer patterns for

outside calls. “Tone 1” to “Tone 3” are bell ringer patterns. “Melody 1” to “Melody 4”

are melody patterns. The factory preset is “Tone 1”.

• You cannot change the ringer tone for intercom calls.

• If you subscribe to a Distinctive Ring Service from your telephone company with 2

or 3 distinct rings, select a bell ringer pattern (Tone 1 to 3). If you select a melody

pattern, you will not be able to distinguish lines by their ringers.

• If you select one of the melody ringer patterns, the ringer will continue to sound for

several seconds if:

— the caller hangs up before you answer the call, or

—

another person answers the call using another phone connected on the same line.

Handset ringer tone

1 Press [MENU].

2 Press the soft key ( ) at “Ringer

setting”.

3 Scroll to “Ringer tone” by pressing [d] or

[B], then press the soft key ( ).

4 Select the desired ringer tone by pressing

[d] or [B].

• The handset will ring and the ringer tone will

change. If the ringer volume has been turned off,

the handset will not ring (p. 18).

• You can also select the ringer tone by pressing

[1] to [7].

5 Press the soft key ( ), then press [OFF].

Handset

SELECT

Ringer setting

SELECT

Ringer tone

1:Tone 1

SAVE

TG5230C_English.fm Page 20 Tuesday, May 11, 2004 9:08 AM

Page is loading ...

Panasonic KX-TG5230C Operating Instructions Manual

Brand: Panasonic

Model: KX-TG5230C

Category: Telephones

Type: Operating Instructions Manual

Download PDF

report

Panasonic KX-TG5230C Operating Instructions Manual

Panasonic KX-TG5230C Operating Instructions Manual

Related papers

Other documents