Dell PowerEdge M605 Quick start guide

Category
Interface cards/adapters
Type
Quick start guide
1
Quick Start Guide
Installation Instructions
This Quick Start Guide describes how to install and configure your new QLogic SANblade
®
host bus adapter (HBA) and
SANsurfer Pro management application in four simple steps:
Step 1. Verify the package contents.
Step 2. Install the HBA hardware.
Step 3. Install the HBA driver.
Step 4. Install the SANsurfer Pro management application.
Keep the HBA in the antistatic bag until installation. The HBA contains parts that can be damaged by
electrostatic discharge (ESD). Before handling the HBA, use standard methods to discharge static
electricity. Place the HBA on the bag when examining it. Retain the bag for future use.
Step 1. Verify the Package Contents
The QLogic HBA is shipped with the following items:
QLogic SANblade HBA
Low-profile bracket (not available in all models)
Dell Documentation Kit
CAUTION!
2
Step 2. Install the HBA Hardware
To install the HBA hardware, you need to open the computer and locate the appropriate bus slot. If necessary, consult
your computer system manual for instructions to remove the computer cover.
Depending on the HBA you are installing, the connector will look like one of the following samples:
Follow these steps to install the HBA hardware (for QME2462 and QME2472 installation instructions, please refer to
your Server Hardware Owner’s Manual):
1. Power off the computer, and then disconnect the power cable.
2. Remove the computer cover and find an empty bus slot.
3. Pull out the slot cover (if any) by removing the screw or releasing the lever.
4. Grasp the HBA by the top edge and seat it firmly into the slot.
5. Refasten the HBA’s retaining bracket using the existing screw or lever.
6. Close the computer cover.
7. Plug in the power cable and turn on the computer.
32-bit PCI-X connector
x4 PCI Express connector
64-bit PCI-X 2.0 connector
QME2462
QME2472
64-bit PCI-X connector
3
Sample motherboard and slots
Step 3. Install the HBA Driver
To retrieve and install the latest HBA driver, access the QLogic support page at:
http://support.qlogic.com/support/newoem_product_list_emc.asp?oemid=65&CATID=58604&type=Dell
Step 4. Install the SANsurfer Pro Management Application
To retrieve and install the latest SANsurfer FC HBA Manager utility, access the QLogic support
page at:
http://support.qlogic.com/support/newoem_product_list_emc.asp?oemid=65&CATID=58604&type=Dell
Congratulations! You have successfully installed your QLogic HBA and
management application!
The following section contains additional information about the SANblade QLogic HBA, including
the LED scheme, troubleshooting, warranty, technical support, and certification information.
RETAINING
BRACKET
LEVER
SLOT COVERS
SYSTEM
CHASSIS
64-BIT PCI-X SLOT
x4 PCI EXPRESS
SLOT
SCREW
HBA
OR
HBA
4
HBA LEDs (Excludes the QME2462 HBA)
QLA234x/QLE220 HBA LED Scheme QME2472 HBA LED Scheme*
Troubleshooting and Technical Support
The QLogic knowledge database contains troubleshooting information for the QLogic SANblade HBAs. Access the data
base from the QLogic web site www.qlogic.com/support/knowledge_base.asp.
For technical support, visit our web site support.qlogic.com,
email us at [email protected], or call at 952-932-4040.
Warranty
The QLogic SANblade HBA comes with a standard three year QLogic warranty, or as specified by other agreements.
Please check the QLogic Web site at www.qlogic.com
for warranty details.
Laser Safety (Excludes QME2462 and QME2472)
FDA Notice
This product complies with DHHS Rules 21CFR Chapter I, Subchapter J. This product has been designed and manufactured according to
IEC60825-1 on the safety label of laser product.
Green LED Amber LED Activity Green LED Amber LED Activity
❍❍Power off Flashing 4 Gbps
●●Power Flashing
1 Gbps or 2Gbps
●❍Online
❍● Link
established
For more information, please refer to your
Server Hardware Owner’s Manual
Flashing Loss of
synchronization
*
LEDs located on Fibre Channel Passthru Module
Alternate
flashing
Alternate
flashing
Firmware error
Flashing Beacon
QLE246x HBA LED Scheme
Yellow LED Green LED Amber LED Activity
Power off
Power on (before firmware init)
Flashing Flashing Flashing Power on (after firmware init)
Yellow, Green and Amber LEDs flashing alternately Firmware error
/Flashing Online, 1-Gbps link established
/Flashing Online, 2-Gbps link established
/Flashing Online, 4-Gbps link established
Flashing Flashing Beacon
5
Agency Certification
QLogic SANblade HBAs
The following sections contain a summary of EMC/EMI test specifications performed on the QLogic SANblade HBAs to comply with radiated
emission, radiated immunity, and product safety standards.
EMI and EMC Requirements
FCC Part 15 compliance: Class A (QLE200, QME2462, QME2472), Class B (QLA234x)
FCC compliance information statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
ICES-003 compliance: Class A (QLE200, QME2462, QME2472), Class B (QLA234x)
For QLE200, QME2462, and QME2472 HBAs: This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numériqué de la classe A est conformé à la norme NMB-003 du Canada.
For QLA234x HBAs: This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.
CE Mark 2004/108/EC EMC Directive compliance:
EN55022:1998/CISPR22:1997 - Class A (QLE200, QME2462, QME2472), Class B (QLA234x)
EN55024:1998
Immunity Standards
EN61000-4-2: ESD
EN61000-4-3: RF Electro Magnetic Field
EN61000-4-4: Fast Transient/Burst
EN61000-4-5: Fast Surge Common/ Differential
EN61000-4-6: RF Conducted Susceptibility
EN61000-4-8: Power Frequency Magnetic Filed
EN61000-4-11: Voltage Dips and Interrupt
EN61000-3-2: Harmonic Current Emission
EN61000-3-3: Voltage Fluctuation and Flicker
VCCI compliance: Class A (QLE200, QME2462, QME2472), Class B (QLA234x, QLE246x)
AS/NZS CISPR22 compliance:
Class A (QLE220, QME2462, QME2472), Class B (QLA234x, QLE246x)
CNS 13438 compliance: Class B (QLA234x)
MIC compliance:
Class A (QLE220, QME2462, QME2472), Class B (QLA234x)
For QLE220, QLA234x, and QME2472 HBAs: Korea MIC Class A Certified
Product Name/Model Fibre Channel HBA
Certification holder QLogic Corporation
Manufactured date Refer to date code listed on product
Manufacturer/Country of origin QLogic Corporation/USA
A class equipment
(Business purpose info/telecommunications
equipment)
As this equipment has undergone EMC registration for business
purpose, the seller and/or the buyer is asked to beware of this point
and in case a wrongful sale or purchase has been made, it is asked
that a change to household use be made.
Caution–Class 1 laser radiation when open
Do not view directly with optical instruments
Attention–Radiation laser de classe 1
Ne pas regarder directement avec des instruments optiques
Vorsicht–Laserstrahlung der Klasse 1 bei geöffneter Abdeckung
Direktes Ansehen mit optischen Instrumenten vermeiden
Varoitus–Luokan 1 lasersäteilyä, kun laite on auki
Älä katso suoraan laitteeseen käyttämällä optisia instrumentteja
CLASS I LASER
Class 1 Laser Product
Appareil laser de classe 1
Produkt der Laser Klasse 1
Luokan 1 Laserlaite
6
Korean Language Format Class A
For QLE246x HBA: Korea MIC Class B Certified
Product Name/Model Fibre Channel HBA
Certification holder QLogic Corporation
Manufactured date Refer to date code listed on product
Manufacturer/Country of origin QLogic Corporation/USA
Korean Language Format Class B
Product Safety Compliance
UL, cUL product safety compliance: QLE220, QLA234x, QLE246x
UL60950-1
CSA C22.2 No.60950-1
Class 1 Laser Product per DHHS 21CFR(J)
2006/95/EC low voltage directive: QLE220, QLA234x, QLE246x
TUV:
-EN60950-1:2001
-EN60825-1:1994+A1+A2
-EN60825-2:1994+A1
B class equipment
(Household purpose info/telecommunications
equipment)
As this equipment has undergone EMC registration for
household purpose, this product can be used in any area
including residential area.
9
样本母板和插槽
步骤 3. 安装 HBA 驱动程序
要检索和安装最新版本的 HBA 驱动程序,请访问 QLogic 支持页:
http://support.qlogic.com/support/newoem_product_list_emc.asp?oemid=65&CATID=58604&type=Dell
步骤 4. 安装 SANsurfer Pro 管理应用程序
要检索和安装最新版本的 SANsurfer FC HBA 管理器公用程序,请访问 QLogic 支持页:
http://support.qlogic.com/support/newoem_product_list_emc.asp?oemid=65&CATID=58604&type=Dell
祝贺您!您已经成功安装了 QLogic HBA 和管理应用程序!
以下小节包含有关 SANblade QLogic HBA 的其它信息,包括 LED 指示灯方案、故障排除、
担保、技术支持和认证信息。
HBA 固定托架
拉杆
插槽盖板
系统
机箱
64 PCI-X 插槽
x4 PCI EXPRESS
插槽
螺钉
HBA
12
韩国语言格式– A
对于 QLE246x HBA:韩国 MIC B 级认证
产品名称 / 型号 光纤通道 HBA
证书持有方 QLogic Corporation
制造日期 参见产品上列出的日期代码
制造商 / 原产国 QLogic Corporation/USA
韩国语言格式– B
产品安全符合性
UL cUL 产品安全符合性 QLE220, QLA234x, QLE246x
UL60950-1
CSA C22.2 No.60950-1
符合 DHHS 21 CFR J)的 1 级激光产品
2006/95/EC 低压规程QLE220, QLA234x, QLE246x
TUV
-EN60950-1:2001
-EN60825-1:1994+A1+A2
-EN60825-2:1994+A1
B 级设备
( 家用目的信息 / 电讯设备)
由于该设备已经在 EMC 注册为用于家用目的,
因此该产品可在包括住宅区的任何区域内使用。
16
疑難排解與技術支援
QLogic 資料數據庫包含 QLogic SANblade HBA 的疑難排解資訊。 請從 QLogic 網站
www.qlogic.com/support/knowledge_base.asp
存取資料庫
如需技術支援請造訪我們的網站 support.qlogic.com
以電子郵件與我們連絡 [email protected] 或是撥打
電話 952-932-4040
保固
QLogic SANblade HBA 附帶標準的三年期 QLogic 保固,或是依其他合約之規定。 如需有關保固的詳細資訊,
請參考位於 www.qlogic.com
QLogic 網站。
雷射安全 ( 不包括 QME2462 QME2472)
FDA 通知
本產品符合 DHHS 規則 21CFR Chapter I,Subchapter J。本產品的設計與製造符合鐳射產品的安全標籤上的 IEC60825-1
機構認証
QLogic SANblade HBA
下面一部分包含針對 QLogic SANblade HBA 執行的 EMC/EMI 測試規格的摘要執行測試的目的是為了符合電場輻射干擾發射
輻射抗擾和產品安全標準。
EMI EMC 需求
符合 FCC 15 部分: Class A (QLE200, QME2462, QME2472), Class B (QLA234x)
FCC 符合性資訊聲明: 本裝置符合美國聯邦通訊委員會規則第 15 條。 操作須符合以下兩種條件 : (1) 本裝置不會造成有害干
擾,並且 (2) 本裝置必須接受任何收到的干擾,包括可能會造成意外操作的干擾。
ICES-003 符合性: Class A (QLE200, QME2462, QME2472), Class B (QLA234x)
QLE200, QME2462, QME2472 HBAs: A 類數位裝置符合 Canadian ICES-003
Cet appareil numériqué de la classe A est conformé à la norme NMB-003 du Canada.
QLA234x HBAs: B 類數位裝置符合 Canadian ICES-003
Cet appareil numériqué de la classe B est conformé à la norme NMB-003 du Canada.
CE Mark 2004/108/EC EMC 指示符合性 :
EN55022:1998/CISPR22:1997 - Class A (QLE200, QME2462, QME2472), Class B (QLA234x)
EN55024:1998
抗擾標準
EN61000-4-2: ESD
EN61000-4-3: RF 電磁場
EN61000-4-4: 快速變動 / 閃爍
EN61000-4-5: 快速浪湧一般 / 差異
EN61000-4-6: RF 傳導耐受性
EN61000-4-8: 電源頻率磁場
EN61000-4-11: 電壓突降與中斷
EN61000-3-2: 諧波電流干擾
EN61000-3-3: 電壓波動與閃爍
Caution-Class 1 laser radiation when open
Do not view directly with optical instruments
Attention — Radiation laser de classe 1
Ne pas regarder directement avec des instruments optiques
Vorsicht — Laserstrahlung der Klasse 1 bei geöffneter Abdeckung
Direktes Ansehen mit optischen Instrumenten vermeiden
Varoitus — Luokan 1 lasersäteilyä, kun laite on auki
Älä katso suoraan laitteeseen käyttämällä optisia instrumentteja
注意 — 1 類鐳射輻射開啟時
請勿直接使用光學設備查看
I 類鐳射產品
I 類鐳射產品 1
Appareil laser de classe 1
Produkt der Laser Klasse 1
Luokan 1 Laserlaite
I 類鐳射產品 1
17
VCCI 符合性: Class A (QLE200, QME2462, QME2472), Class B (QLA234x, QLE246x)
AS/NZS CISPR22 符合性:
Class A (QLE220, QME2462, QME2472), Class B (QLA234x, QLE246x)
CNS 13438 符合性: Class B (QLA234x)
MIC 符合性:
Class A (QLE220, QME2462, QME2472), Class B (QLA234x)
QLE220, QLA234x, QME2472 HBAs: Korea MIC A 類認證
產品名稱 / 型號 光纖通道 HBA
證書持有者 QLogic Corporation
製造日期 請參閱產品上列出的日期代碼
製造商 / 原產地 QLogic Corporation/USA
韓文格式— A
QLE246x HBA: Korea MIC B 類認證
產品名稱 / 型號 光纖通道 HBA
證書持有者 QLogic Corporation
製造日期 請參閱產品上列出的日期代碼
製造商 / 原產地 QLogic Corporation/USA
韓文格式— B
產品安全符合性
ULcUL 產品安全符合性 : QLE220, QLA234x, QLE246x
UL60950-1
CSA C22.2 No.60950-1
1 類鐳射產品 DHHS 21CFR (J)
2006/95/EC 低電壓符合性 : QLE220, QLA234x, QLE246x
TUV:
-EN60950-1:2001
-EN60825-1:1994+A1+A2
-EN60825-2:1994+A1
A 類設備
( 商業用途資訊 / 電訊設備 )
由於此設備已經過 EMC 註冊而用於商業用途,銷售方和 / 或買
方需要確知這一點。如果發生誤銷或誤購的情況,則必須變更
為家庭使用。
B 類設備
( 家庭用途資訊 / 電訊設備 )
由於此設備已經過 EMC 註冊而用於家庭用途,因此可以
在任何區域使用此產品 ( 包括居住區 )
51
Krok 3. Instalacja sterownika HBA
http://support.qlogic.com/support/newoem_product_list_emc.asp?oemid=65&CATID=58604&type=Dell
Krok 4. Instalacja aplikacji obsługi karty SANsurfer Pro
Aby pobrać i zainstalować najnowszą wersję programu SANsurfer FC HBA Manager, należy wejść na
stronę obsługi technicznej QLogic:
http://support.qlogic.com/support/newoem_product_list_emc.asp?oemid=65&CATID=58604&type=Dell
Gratulacje! Karta QLogic HBA i aplikacja obsługi karty zostały pomyślnie
zainstalowane!
Poniższa część zawiera dodatkowe informacje o karcie SANblade QLogic HBA, w tym schemat diod
LED, sposoby rozwiązywania problemów oraz informacje o gwarancji, obsłudze technicznej i certyfikacji.
WSPORNIK
MOCUJĄCY
KARTY HBA
DŻWIGNIA
POKRYWA
GNIAZDA
PŁYTA
MONTAŻOWA
64-BITOWE
GNIAZDO PCI-X
GNIAZDO x4 PCI
EXPRESS
ŚRUBKA
KARTA HBA
LUB
© 2007 QLogic Corporation. QLogic, the QLogic logo, and SANblade are registered trademarks of QLogic Corporation. SANsurfer is a
trademark of QLogic Corporation. All other trademarks are the property of their respective companies. Information supplied by QLogic is
believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation
reserves the right, without notice, to make changes in product design or specifications.
© 2007 QLogic Corporation QLogicQLogic 徽标和 SANblade QLogic Corporation 的注册商标。 SANsurfer QLogic Corporation
的商标。 所有其它商标均为其各自公司的财产。 QLogic 提供的信息据信是准确可靠的。 QLogic Corporation 对本手册中的任何
错误不承担责任。 QLogic Corporation 保留对产品设计或规格随时作出更改而不做出通知的权利。
© 2007 QLogic Corporation. QLogicQLogic 標誌和 SANblade QLogic Corporation 的註冊商標。 SANsurfer QLogic Corporation
的商標。 所有其他商標分屬於其各自公司的財產。QLogic 所提供的資訊被認定為準確且可靠的資訊。 QLogic Corporation 對於
本手冊中的任何錯誤不承擔任何責任。QLogic Corporation 保留對產品設計或規格進行修改而不另行通知的權利。
© 2007 QLogic Corporation. QLogic, le logo QLogic et SANblade sont des marques déposées de QLogic Corporation. SANsurfer est une
marque de QLogic Corporation. Toutes les autres marques sont la propriété de leurs détenteurs respectifs. Les informations fournies par
QLogic sont reconnues comme étant précises et fiables. QLogic Corporation ne peut être tenue pour responsable des erreurs pouvant figurer
dans cette brochure. QLogic Corporation se réserve le droit de modifier sans préavis la conception ou les spécifications des produits.
© 2007 QLogic Corporation. QLogic, das QLogic-Logo und SANblade sind eingetragene Marken der QLogic Corporation. SANsurfer ist eine
Marke der QLogic Corporation. Alle anderen Marken sind Eigentum der jeweiligen Unternehmen. Die von QLogic bereitgestellten
Informationen sind nach bestem Wissen korrekt und zuverlässig. QLogic Corporation übernimmt keinerlei Haftung für mögliche Fehler in
diesem Dokument. QLogic Corporation behält sich das Recht vor, ohne vorherige Ankündigung Änderungen am Produktdesign
beziehungsweise an den Spezifikationen vorzunehmen.
© 2007 QLogic Corporation. QLogic, il logo QLogic e SANblade sono marchi registrati di QLogic Corporation. SANsurfer è un marchio
commerciale di QLogic Corporation. Tutti gli altri marchi commerciali sono proprietà delle rispettive società. Le informazioni fornite da
QLogic sono ritenute accurate e affidabili. QLogic Corporation non si assume alcuna responsabilità relativa ad alcun errore contenuto in
questo opuscolo. QLogic Corporation si riserva il diritto di apportare modifiche, senza preavviso, alla progettazione o alle specifiche del
prodotto.
© 2007 すべての著作権は QLogic Corporation にあります。QLogicÅAQLogic のロゴ、および SANblade は、QLogic Corporation の登録商標で
す。SANsurferQLogic Corporation の商標です。その他のすべての商標は、各所有企業の財産です。QLogic が提供する情報は、正確で信頼で
きるものです。本書の内容の誤りにつきましては、QLogic Corporation はその責任を負うものではありません。QLogic Corporation は、製品の設
計または仕様を予告なく変更する権利を有します。
© 2007 QLogic Corporation. QLogic, QLogic 로고 SANblade QLogic Corporation 등록 상표입니다 . SANsurfer
QLogic Corporation 상표입니다 . 기타 모든 상표는 해당 소유권자의 자산입니다 . QLogic 정확하고 신뢰성 있는 정보를
공하기 위해 노력하고 있습니다 . QLogic Corporation 에서는 책자의 모든 오류에 대해 책임을 지지 않습니다 . QLogic Corporation
제품 디자인이나 사양을 사전 통보 없이 변경할 있습니다 .
© 2007 QLogic Corporation. QLogic, logo QLogic i SANblade są zarejestrowanymi znakami handlowymi firmy QLogic Corporation. SANsurfer jest
znakiem handlowym firmy QLogic Corporation. Wszystkie inne znaki handlowe są własnością odpowiednich firm. Informacje podane przez firmę
QLogic uznaje się za dokładne i pewne. Firma QLogic Corporation nie ponosi żadnej odpowiedzialności za jakiekolwiek błędy w tej broszurze. Firma
QLogic Corporation zastrzega sobie prawo wprowadzenia zmian w projekcie lub w danych technicznych produktu bez powiadomienia.
© 2007 QLogic Corporation. QLogic, o logotipo da QLogic e SANblade são marcas comerciais registradas da QLogic Corporation. SANsurfer
é marca comercial da QLogic Corporation. Todas as outras marcas comerciais são de propriedade de suas respectivas empresas. Acreditamos
que as informações fornecidas pela QLogic sejam precisas e confiáveis. A QLogic Corporation não assume responsabilidade por quaisquer
erros neste folheto. A QLogic Corporation reserva-se o direito de, sem aviso prévio, fazer alterações no projeto ou nas especificações de
seus produtos.
(c) QLogic Corporation, 2007. QLogic, логотип QLogic и SANblade являются торговыми марками QLogic Corporation. SANsurfer
является торговой маркой QLogic Corporation. Все остальные товарные знаки являются собственностью соответствующих
компаний. Информация, предоставляемая QLogic, считается точной и надежной. QLogic Corporation не несет ответственность за
возможные ошибки в этой брошюре. QLogic Corporation оставляет за собой право без предупреждения вносить изменения в продукт
или его характеристики.
© 2007 QLogic Corporation. QLogic, el logotipo QLogic logo y SANblade son marcas comerciales registradas QLogic Corporation. SANsurfer
es una marca registrada de QLogic Corporation. Las otras marcas son propiedad de sus respectivas empresas. La información suministrada
por QLogic es precisa y confiable. QLogic Corporation no asume ninguna responsabilidad por los errores que puedan aparecer en este
. QLogic Corporation לש םיירחסמ םינמיס םה SANblade QLogic וגולה ,QLogic . © 2007 QLogic Corporation
.המאתהב תורבחה תולעבב םיאצמנ םירחאה םיירחסמה םינמיסה לכ . QLogic Corporation לש ירחסמ ןמיס אוה SANsurfer
תויועטל תוירחא לכ המצע לע תלבקמ הניא QLogic Corporation .ןימאו קיודמ תויהל רומא QLogic ידי-לע קפוסמה עדימה
.שארמ העדוה אלל ,רצומה לש טרפמב וא ןונכתב םייוניש עצבל תוכזה תא המצעל תרמוש QLogic Corporation .הז ןולעב ןהשלכ
QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656
949.389.6000 www.qlogic.com
FC0054519-00 B
1 / 1

Dell PowerEdge M605 Quick start guide

Category
Interface cards/adapters
Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document