Safety First!
Please follow all the safety precautions listed below for safety and to reduce the risk of
injury or electrical shock.
• Read all the instructions carefully before using your appliance and keep them for
future reference.
• Unplug the appliance from the mains supply when not in use, when removing
or attaching the blender jug, or before cleaning any part of the appliance.
• This blender is for household use only. Do not use it for professional catering.
• Do not use the blender outdoors.
• Do not immerse the blender base unit or the electrical cord or plug in liquids.
• Do not use the blender near a source of heat or on an unstable surface.
• Do not use your blender in damp or wet conditions.
• Never let children operate this appliance. Close supervision is necessary when
this appliance is used near children.
• This appliance is not intended for use by persons (including children) with
reduced sensory or mental capabilities, or lack of experience and knowledge unless
they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Ensure that the mains cable does not touch any hot surface and that it does not
overhang the edge of your work surface.
• When unplugging the mains cable, hold the mains plug top, not the mains cable.
• If the mains cable is damaged it must be replaced by the manufacturer, its service
agent, or similarly qualied persons in order to avoid a hazard.
• Do not use attachments or accessories which are not recommended by the
manufacturer. They may cause malfunction or injury.
• Store the blender away from direct sunlight and out of the reach of children.
When operating your blender:
• Do not place your hand in the blender jug. The sharp blade may cause injury.
Use a plastic or wooden spatula.
• Never insert any hard object or implement into the blender jug when it is
operating. This may cause damage to the appliance and personal injury.
• Do not place meat containing bones or fruits with large hard stones in the blender jug.
• If the blender becomes clogged, switch off and unplug the mains cable from the
mains before cleaning the obstruction. Check carefully for damage.
• There are no user serviceable parts in your blender.
• Do not operate the appliance with a damaged mains cable or mains plug or after the
appliance or any attachment has been damaged. Seek qualied technicians for
assistance.
• Do not use the appliance for any purpose not expressly specied in this manual.
Specications
Power : 230V~50Hz, 500W
Capacity of Jug : 1.6 litres max.
Duty Cycle : 3 minutes ON; 5 minutes OFF
Visit Partmaster.co.uk today for the easiest way
to buy electrical spares and accessories.
With over 1 million spares and accessories available
we can deliver direct to your door the very next day.
Visit www.partmaster.co.uk
Or call
0870 6001 338
(UK customers only)
Calls charged at National Rate.
DSG Retail Ltd. Maylands Avenue Hemel Hempstead
Hertfordshire HP2 7TG England
Unpacking
Remove all packaging from the blender. Retain the packaging. If you dispose of it please
do so according to any recycling regulations.
The packing includes:
• The Blender Main Unit
• The Blender Jug (Part number: XB9196-5-15)
• The Blender Jug Cover (Part number: XB9196-2)
• Stopper/ Measuring Cup (Part number: XB9196-1)
• Instruction Manual (Part number: XB9196-3)
If items are missing or damaged, please contact Partmaster (UK only).
Tel: 0870 6001 338 for assistance.
GB - 1
GB - 5
This symbol on the product or in the instructions means that your
electrical and electronic equipment should be disposed at the end of
its life separately from your household waste. There are separate
collection systems for recycling in the EU.
For more information, please contact the local authority or your
retailer where you purchased the product.
Instruction Manual
C16BSS09
STAINLESS STEEL
BLENDER
Congratulations on the purchase of your new Carlton blender.
We recommend that you spend some time reading this instruction
manual in order to fully understand all the operational features it offers.
Read all the safety instructions carefully before use and keep this
instruction manual for future reference.
Storage
After all the components have been washed and dried, re-assemble the blender and
stow it out of direct sunlight and out of the reach of children.
The cable may be wound around the lugs at the bottom of the appliance for easier storage.
Cleaning
Cleaning the blender jug:
1. Pour about 500ml of warm soapy water into the jug and place the jug on the base.
2. Turn and hold the Selector knob to ‘P’ for a few seconds to loosen any food particles
and free them from the blade.
• Remove the jug, pour away the water and rinse in fresh running water. Repeat 1
and 2 by fresh water.
• Alternatively the jug may be immersed in warm soapy water and cleaned using a
long handled brush. Do not touch the blade when cleaning.
• Wash the lid and stopper separately in warm soapy water, rinse and allow to dry.
• CAUTION: The jug body should be handled carefully. The jug contains moving
parts - do not leave the jug immersed in water for any longer than necessary to
clean it or you may affect the efficient running of the blender.
• DO NOT wash the jug or attachments in a dishwasher.
Cleaning the base:
• Ensure the blender is switched off and unplugged from the mains.
• Wipe the outer surface of the motor unit with a damp cloth. Never use abrasive
cleaners or scouring creams.
Never immerse the base in water when cleaning.
NOTE: Do not run the appliance continuously for more than 3 minutes. After a full
3 minute cycle allow the blender to rest for another 5 minutes before
using it again.
• During blending, you can feed in small amounts of food or liquid through the jug
lid. To do this:
• Hold the lid
• Turn the stopper slowly anti-clockwise to free it and then lift it out.
• Gradually feed pieces of food or liquids into the jug through the feeder.
• Fit the stopper back when you have nished.
DANGER OF SCALDING! If you spill liquid on the blender base immediately switch
o and wipe dry.
GB - 2
GB - 3
GB - 4
Your blender and its components
Operation
• Make sure the jug and the lid are secure and in the LOCK position.
• Set the selector switch to ‘0’.
• Plug your blender into the mains and switch on the power.
Blender's Operation Modes
Continuous (Normal)
operation
Pulsed operation
• Select the desired operating speed. There are
5 speeds. Move the Selector knob progressively
to the right to increase the speed. When you
start blending use a low speed to begin with
and gradually increase the speed if necessary.
• To stop the operation, turn the knob back to ‘0’.
Use this mode where ingredients need to be
blended in small repeated bursts.
• Turn the Selector knob to ‘P’ and hold
it there for a short period.
• To stop the operation, release the knob
which will automatically return to ‘0’.
After Use
After you have nished blending:
• Set the Selector knob ‘0’.
• Hold the jug with the handle carefully and turn it clockwise (towards you) to release
the jug. (This may be easier with one hand on the base and one hand holding the
jug handle).
• To pour out the contents, rotate the lid of the jug anti-clockwise to free it and then
lift off the lid. Pour or spoon the contents out carefully.
• Switch the blender off to “0” and unplug it after use.
• Remove the jug from the base.
Before Use
• Before using your blender for the rst time, wash the jug, blade assembly, lid and
stopper. Rinse throughly and dry.
• Place the base unit on a stable surface, free from heat and moisture and within
easy reach of a mains outlet. The mains cable should not be taut.
Preparing and Filling the ingredients
• Cut the ingredients into 25mm (1”) cubes before placing them into the blender jug.
If the food is very solid or dry, cut the pieces into smaller cubes.
• Fill the blender jug with the ingredients.
• Do not overll the jug. The maximum capacity is 1600 ml, but we suggest you do not
exceed 1250 ml. If you are preparing a large quantity use several smaller batches.
• If the ingredients are very dry, put some liquid into the jug. You should never
try to reduce dry ingredients in the blender.
Fitting the lid
• Place the lid in the top of the jug and turn the lid fully clockwise. If the lid is properly
secured, you will hear a “click” sound.
Fitting the stopper
The stopper has an integral measuring cup
useful for measuring small amounts.
• Place the stopper in the slots in the lid and turn fully clockwise to lock. If the stopper
is properly secured, you will hear a “click” sound. To avoid splashing, always operate
the blender with the stopper rmly in place.
Fitting the jug to the base
• Place the jug on the blade assembly as show. The jug will t only one way round. If
the jug is not properly tted to the base the blender will not start.
6
7
8
1
2
3
4
5
Base Unit
Stopper/Measuring Cup
Handle
Blade Assembly
5
6
7
8
Safety Lid
Measuring Scale
Blender Jug
Speed Selector
1
2
3
4
NOTE: Never blend very hot liquids in the blender. This is dangerous as
the contents may erupt.
The lid must be secured to the jug and the jug to the base otherwise the
blender will not operate!
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Myria MY4107 User manual
-
Currys Essentials C15BW10 User manual
-
-
Matsui M15BW09E User manual
-
Tricity Bendix TBL10 User manual
-
SEVERIN SM 3714 Owner's manual
-
SEVERIN SM 3713 User manual
-
Breville Pick & Mix Operating instructions
-
Cookworks 1.5L Jug Blender User manual
-
