Pure Clean PUCRC62 User guide

Brand: Pure Clean

Model: PUCRC62

Category: Robotic vacuum cleaners

Type: User guide

www.PyleUSA.com www.PyleUSA.com

Start key

Indicator

light

Charging poles

Ground detect

sensors

Frontwheel

Side brush

Suction inlet

Ground detect

sensors

Driving wheel

Power switch

Back infrared

receiver

Surface cover

Dustbin

Side detect sensors

Front sensor window

Front infrared receiver

COMPONENTS OF THE PRODUCT

• Before using the product, please

take out two side brushes from the

package and assemble them onto

the bottom of the product softly

according to this installation

diagram.

CONTENT

CONPONENTS OF THE PRODUCT

IMPORTANT NOTICE

1. Guidelines for safe use

2. Notes for charging

3. Applicability

PRODUCT USE

1. Charging of main body

2. Power on/operating/pause/power o

3. Cleaning mode

4. Assemble mop

MAINTENCE

1. Brush cleaning

2. Dustbin Cleaning

3. Wheels and sensor windows cleaning

FAILURE CHECKING

1. Alarming notice

2. Notice

PARAMETER

www.PyleUSA.com www.PyleUSA.com

IMPORTANT NOTICE

GUIDELINES FOR SAFE USE

NOTES FOR CHARGING

APPLICABILITY

Please read the following safety instructions and follow all normal safety

precautions carefully before using this product. Any operation unconformable to

this manual may result in damage of the product.

• Please remove fragile items and items that may entangle side brush and suction

channel (e.g.wire and curtain) on the oor before use.

• Don't stand or squat on this product, to avoid damage of the machine.

• Please turn oﬀ the power switch at the bottom of the machine when not in use

for a long period of time

• Please remove the wasted battery oﬀ the machine for safe recycling before the

product is out of service.

• Any technician except for technicians specied by our company shall

disassemble, maintain and modify the product.

• Use only the power cords and power adapters supplied by the product

manufacturer. Using diﬀerent power cords and adapter may damage the product

• The power shall be supplied in accordance with the voltage indicated on the

nameplate of the power adapter.

• Do not use the device if the plug of the power adapter is damaged

• Unplug the power cord if the machine is not to be used for a long period of time

• The product is applicable to dry and at ground indoors, such as hardwood,

ceramic tile etc.

• Please don' t use this product in humidity (such as the bathroom).

• Please don' t use this product outdoors.

Power & charging indicator light

Infrared transmit window

Charging adaptor socket

Charging poles

DOCKING STATION

DOCKING STATION CHART INDICATOR LIGHT

DOCKING STATION STATUS INDICATOR LIGHT

Connect with adaptor

Connect with main body

Red light keeps on

Blue light ashes

REMOTE CONTROL

• Press this key whencleaner is working, will enter standby mode

• Enter auto charging mode

• Press this key, cleaner goes forward

• Press this key, cleaner goes backward

• Press this key, cleaner goes left

• Press this key, cleaner goes right

• Press this key, when cleaner is working, will enter standby mode

• Press this key, cleaner will enter auto clean mode

• Press this key, cleaner will enter spot clean mode

• Press this key, cleaner will enter edge clean mode

• Press this key, cleaner will enter Z mode

• Press this key, cleaner will enter left spiral mode

• Press this key, cleaner will enter right spiral mode

• Before using the remote control, please take out the plastic piece that insulate

the battery before power on.

• Battery type is CR2032, +3V button battery.

• Don' t use the remote control near the docking station.

Notes:

0302

www.PyleUSA.com www.PyleUSA.com

PRODUCT USE

CHARGING OF MAIN BODY

POWER ON / OPERATING / PAUSE / POWER OFF

CHARGING STATUS

DOCKING STATION MAIN BODY

Charging

status

chart

Before charging The red lights on The orange light Is on (low battery)

During charging The blue light ashes The green light Hashes

Fully charged The blue light ashes The green light keeps on

• Notes:

1. Please make sure the docking station is connected well with the adapter.

2. If you will not use the cleaner for a long time, please fully charge the cleaner and

tum oﬀ. Please charge the cleaner every 3 months to avoid over discharge of the

battery.

• Poweron

Power on the main body by turning on the power switch and the main body will

be in standby mode.

• Put the auto charging docking station in place and

connect the adapter. The red power indicator light

on the auto charging docking station keeps on.

Notes: Place the docking station along the wall. No

obstacle or hollow areas 2m away from the docking

Station in front and 0.5 on the left and right (Refer to

Figure)

• The following three methods can be used to

charge the main body.

A: Automatic return

When the machine is low battery at work, the orange

indicator light will be on and a buzzer will alarm the

low battery, then the machine will enter the state of

looking for the docking station and match the

docking station automatically for charging.

B: Articial selection

When the main body is in standby state or working,

press the Docking key, the main body will search for

the docking station for charging

C: Manual operation

Place the main body on the auto charging docking

station manually. Pay attention to the well contact

between the charging pole pieces at the bottom of

main body and the charging pole pieces of docking

station.

• Operating: Operate the machine by pressing the start key on the robot, it will

enter working state.

• Pause: Pressing the start key on the robot, it will pause and enter standby state

• Power oﬀ: Turn oﬀ the power switch of the main body, robot is powered oﬀ.

CLEANING MODE

In order to adapt to diﬀerent ground environment and achieve more thorough

cleaning, the main body is equipped with various cleaning modes.

• Auto cleaning mode

Press the key on the main body, or the Auto clean key on remote control, the main

body will enter Z mode, and in specic situation, it will enter edge cleaning mode.

• Spot cleaning mode

Press Spot clean on remote control, the main body will enter spiral mode of

cleaning in a range of about 1 m2 area, and will stop after 2 minutes of cleaning.

• Edge cleaning mode

The robot will clean along the wall under this mode, and will enter auto clean

mode when nish edge cleaning.

• Spiral cleaning mode

The robot will clean in left or right spiral clean mode, and will enter auto clean

mode when nish spiral cleaning.

Velcro

ASSEMEMBLE THE MOP

• If you need to use the mopping function,

please take out the mop and stick it on the

bottom of the main body as per picture.

Remark:

Make sure the mop is stuck smoothly and

aligned, the mop is for dry mopping only,

avoid using liquid.

0504

www.PyleUSA.com www.PyleUSA.com

MAINTENANCE

BRUSH CLEANING

FAILURE CHECKING

ALARMING NOTICE

DUSTBIN CLEANING

WHEELS AND SENSOR WINDOWS CLEANING

MOP CLEANING

• Please timely clean the brushes when the robot

is dirty. Please pull out the brushes for cleaning

is needed. Change the brush if it has damage

• Please timely clean the dustbin and inner lter after the robot is done cleaning.

(if you wash the lter, please dry it rst before using it again.)

• Notes:

1. Please carefully check the sucking port if clean or not after pulling out the

dustbin.

2. The lter net can be washed, please dry it rst and before using it again.

• Piease timely clean the wheels and sensor windows.

• Use the dry mopping function, when the

mop is dirty, please take oﬀ the mop and

wash in water then dry it for future use.

Remark:

Remove the mop carefully to prevent

damaging the velcro at the bottom of the

cleaner

The robot will give warning tone every 10 seconds when it comes to malfunction.

WARNING TONE FAILURE CAUSE SOLUTION

Infrared detecting

system problem

Motor problem

Power of the robot is limited

Left and right wheel problem

Pure Clean PUCRC62 User guide

Brand: Pure Clean

Model: PUCRC62

Category: Robotic vacuum cleaners

Type: User guide

Download PDF

report

Pure Clean PUCRC62 User guide

Pure Clean PUCRC62 User guide

Related papers

Other documents