Riva RC2103HD-6611 Installation guide

Category
Security cameras
Type
Installation guide

This manual is also suitable for

Riva RC2103HD-6611 is a 5 Megapixel CMOS Image Sensor network camera with a wide view (182°) angle and a Certified ImmerVision Enables Panomorph Lens. It supports H.264 Baseline, Main, High profile(MPEG-4 Part 10/AVC), MJPEG(Motion JPEG) video encoding formats and has two-way Audio Streaming with G.711µLaw. Other key features include:

  • Digital Day/Night
  • Digital WDR
  • Three different view types(Single, Quad, Panorama)
  • Three different Camera Position(Ceiling, Wall, Ground)
  • microSD/SDHC slot
  • Power Over Ethernet (PoE)
  • VCA Presence (Standard)
  • VCA Surveillance (Optional)
  • VCA Pro (Optional)

Riva RC2103HD-6611 is a 5 Megapixel CMOS Image Sensor network camera with a wide view (182°) angle and a Certified ImmerVision Enables Panomorph Lens. It supports H.264 Baseline, Main, High profile(MPEG-4 Part 10/AVC), MJPEG(Motion JPEG) video encoding formats and has two-way Audio Streaming with G.711µLaw. Other key features include:

  • Digital Day/Night
  • Digital WDR
  • Three different view types(Single, Quad, Panorama)
  • Three different Camera Position(Ceiling, Wall, Ground)
  • microSD/SDHC slot
  • Power Over Ethernet (PoE)
  • VCA Presence (Standard)
  • VCA Surveillance (Optional)
  • VCA Pro (Optional)
www.rivatech.de
Specification subject to change without notice
RC2103HD-6611
Installation Guide
Precaution
Please read this manual carefully before installing the unit.
Never disassemble the camera. Unauthorized disassembly may cause equipment
failure or damage to the unit.
Please do not install the camera in a place exposed to direct sunlight.
Do not operate the camera in environments beyond the specified temperature.
Refer to Environment Condition on APPENDIX (A): SPECIFICATIONS in this manual.
Before applying power to the camera, check the power source to ensure that it is
within the specifications. Refer to Electrical Characteristics on APPENDIX (A):
SPECIFICATIONS.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 3
Table of Contents
Precaution ................................................................................................................ 2
1. FEATURES ............................................................................................................. 4
2. PACKAGE CONTENTS............................................................................................. 5
3. PART NAMES ........................................................................................................ 6
4. INSTALLATION ...................................................................................................... 7
4.1. Installing the camera .......................................................................................................... 7
4.1.1. Semi-Flush Mount ....................................................................................................... 7
4.1.2. Flush Mount ................................................................................................................ 9
4.1.3. Compatible Accessories ............................................................................................ 11
4.2. Setting the Image Attributes ............................................................................................ 12
5. CONNECTIONS .................................................................................................... 13
6. CONFIGURATION ................................................................................................ 17
6.1. Set up network environment ........................................................................................... 17
Generic IP Environment ...................................................................................................... 17
Custom IP Environment ...................................................................................................... 18
6.2. View video on web page .................................................................................................. 19
6.3.1. ActiveX Installation .................................................................................................... 19
6.2.2. View video using IPAdmin Tool ................................................................................. 20
6.3. Reboot .............................................................................................................................. 21
6.4. Factory Default ................................................................................................................. 21
6.5. Safe Mode ........................................................................................................................ 21
APPENDIX (A): SPECIFICATIONS .............................................................................. 23
Summary ................................................................................................................................. 23
Electrical Characteristics ......................................................................................................... 24
Environment Condition ........................................................................................................... 24
Mechanical Condition ............................................................................................................. 24
APPENDIX (B): POWER OVER ETHERNET ................................................................. 25
Power Comparison .................................................................................................................. 25
APPENDIX (C): DIMENSIONS ................................................................................... 26
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ................................. 27
REVISION HISTORY ................................................................................................. 29
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 4
1. FEATURES
Camera
1/2.55 Megapixel CMOS Image Sensor
Wide view (182°) angle
1.12mm, F2.0 Certified ImmerVision Enables Panomorph Lens
Digital Day/Night
Digital WDR
Video
H.264 Baseline, Main, High profile(MPEG-4 Part 10/AVC), MJPEG(Motion JPEG)
H.264 and MJPEG: Max 14fps in 4:3 mode
H.264 and MJPEG: Max 30fps in 16:9 mode*
Three different view types(Single, Quad, Panorama)
Three different Camera Position(Ceiling, Wall, Ground)
Text Overlay
Audio
Two-way Audio Streaming
G.711µLaw
Network
10/100 Base-T Ethernet
Integration
Software Development Kit (SDK) available
ONVIF Compliant (Profile S & Profile G)
* ONVIF Profile G is supported from FW V1.8.0 or higher.
General
microSD/SDHC slot
Power Over Ethernet (PoE)
Video Contents Analytics (VCA)
VCA Presence (Standard)
VCA Surveillance (Optional)
VCA Pro (Optional)
* VCA Pro is supported from FW V1.8.0 or higher.
* If VCA is activated, frame rate is limit to max15fps@1080p. Limitation based on V.1.9.0
firmware release and could be changed without notice.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 5
2. PACKAGE CONTENTS
Please unpack the package carefully and handle the equipment with care.
The package contains:
Camera
DC Power Adaptor
Universal Plugs
Quick Installation Guide
Terminal Blocks
FMB mount (for flush mount)
Screws and Anchor Blocks
Cable Hole Cap
DC Power Jack Cable
Installation Template
Note
i
The contents above are subject to change without prior notice.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 6
3. PART NAMES
Reset Button
This button will restart the device or reset it to factory default settings. Refer to 6.3. Reboot and
6.4. Factory Default for more details.
PAL/NTSC Button
Pressing the button cycles through PAL, NTSC, and no video output mode: No video output -> PAL->NTSC
Terminal Connector
Connector for cable connection of video output, audio input/output and digital input/output.
Refer to 5. CONNECTIONS for more details.
LAN Connector
RJ45 LAN connector for 10/100 Base-T Ethernet(PoE supported)
microSD / SDHC card slot
The camera supports up to 32GB. Class 4 and higher SD card is recommended for HD recordings.
Power Adapter Connector
DC 12V power supply connection
* Models and their appearance are subject to change without any prior notice.
*The reset button is located under this plate.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 7
4. INSTALLATION
4.1. Installing the camera
4.1.1. Semi-Flush Mount
Installation Template
(Unit: mm)
Caution
!
Installation templates image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package
separately.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 8
1) Place the installation template included in
the package on the desired installation
surface.
2) Drill holes on the correct spots based on
the template paper, and insert the anchor
blocks into the holes.
3) Open the dome cover.
*Refer to the caution below for the details of how
to open the cover.
4) Connect necessary cables including a LAN
cable and a power cable to the camera.
5) Hold the camera against the surface where
the camera will be mounted by matching the
alignment holes with the corresponding
anchor blocks.
6) Route the cables through the cable hole at
the bottom of the camera, and tighten the
anchor blocks with the screws.
7) Attach the dome cover on the main body,
and lock it up by rotating the dome cover.
*Refer to the caution below for the details of how
to attach the dome cover.
Caution
!
When placing the dome cover, look for the carved triangle mark on both dome
cover and main body. Both triangles should be aligned together when placing the
cover. Once the cover has been placed, rotate the dome cover clockwise for a
secure lock. To detach the cover, rotate the cover counterclockwise. Then, align
the two triangle marks each other, and pull the cover.
Caution
!
To prevent products from damage, place the camera on a stable and
non-vibrating surface. If the stability is in doubt, consult safety personnel for
reinforcements, and then proceed with the installation.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 9
4.1.2. Flush Mount
(Unit: mm)
Caution
!
Installation templates image size scale in this installation guide is not 1:1.
The correct-size template design paper can be found inside the package
separately.
Installation template (FMB)
21 V1.0
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 10
1) Place the installation template included
in the package on the desired installation
surface.
2) Drill holes on the correct spots based on
the template paper, and insert the anchor
blocks into the holes.
3) Open the dome cover.
*Refer to the caution below for the details
about how to open the cover.
4)
Connect necessary cables including a
LAN cable and a power cable to the
camera.
5) Unscrew the three bolts attached on the
dome covers surface, and place the FMB
mount between the dome shell and the
bottom circular cylinder. Then, align the
three screw holes on each component
together, and tighten the three
components with the bolts included in the
package.
6) Attach the three components-combined
dome cover to the main body, and lock it
up by rotating the cover.
*Refer to the caution below for the details
about how to lock the cover.
7) Tighten the cameras body into the
mounting surfaces anchor blocks by
inserting the screws included in the
package through the screw holes around
the edge of the FMB mount.
Caution
!
When placing the dome cover, look for the carved triangle mark on both dome
cover and main body. Both triangles should be aligned together when placing the
cover. Once the cover has been placed, rotate the dome cover clockwise for a
secure lock. To detach the cover, rotate the cover counterclockwise. Then, align
the two triangle marks each other, and pull the cover.
Caution
!
To prevent products from damage, place the camera on stable and non-vibrating
surfaces. If the stability is in doubt, consult safety personnel for reinforcements,
and then proceed with the installation.
circular cylinder
FMB mount
dome shell
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 11
4.1.3. Compatible Accessories
The various combinations of the compatible accessories to mount this camera model are as
follows.
Model Names & Combinations
WMB-3000 + (CMA-U100 or PMA-U100)
WMB-3000P + PMC-3000 + (JBK-U100) + (CMA-U100 or PMA-U100)
CMB-3000P + PMC-3000
GBA-3000
Refer to the corresponding accessory models installation guide for the instructions.
Note
i
The models in the parenthesis, (), may or may not be required depending on
the installation environment.
Model Image
WMB-3000
WMB-3000P
CMB-3000P
PMC-3000
JBK-U100
CMA-U100
PMA-U100
GBA-3000
WMB-3000/CMB-3000
This guide i llustrates how to asse mble the corner mount adapter and
pole mount adapter.
Check the let ter of the alphabet assi gned to each adapter and tighten
the screws in the corresponding holes to assemble the adapter.
A-A-A(M4TAP)
A
A
A
IPE-3500
IPE-2100
IPN-2102
IPN-3102
IPN-3502
IPE-3100
A
A-A-A : IPN3202HD
B-B : IPN352HD & IPX5502HD
C-C : IPN3402HD
D-D-D : IPN2103HD & IPN3102HD & IPN3502HD
D
D
B
A C
B
A
C
D
A-A-A : IPN6802HD
B-B-B : IPN6702HD
C-C-C-C : IPN6602HD
D-D-D-D : WMB-3000P & CMB-3000P
1
HOUSING COVER에 WALL MOUNT CABLE을 통과시킨다.
2
3
1
2
3
1
2
1
2
1
2
3
4
5
1
2
3
4
5
1
2
HOUSING COVER와 WALL MOUNT BRACKET을 조립한다
결합 후 상태 이미지
3mm Hex Wrench를 사용하여 볼트를 푼다. (4EA 동일 방법)
Hinge를 젖힌 후 빼낸다. (2EA 동일 방법)
B
BULLET CAMERA의 CABLE을 HOUSING COVER에 통과시킨다.
장착하는 CAMERA에 맞는 BOLT를 사용하여
CABLE을 GASKET에 끼운 후 위치에 맞게 삽입한다.
CABLE을 GASKET에 맞춰 정리한 후 GASKET을 접어 닫는다.
M3x12 BOLT를 사용하여 PLATE를 조립한다.
왼쪽 상세 이미지를 참고 하여 CABLE GLAND조립한다.
CABLE GLAND를 HOUSING COVER에 완전히 조립한다.
HOUSING COVER의 LOWER와 UPPER
HOUSING COVER의 UPPER와 LOWER를
BB
A A
A
C C
CC
D D
DD
PMA-U100 CMA-U100 WMA-U100
M5x12 BOLT를 사용하여 HOUSING COVER와 PMA-U100을 체결한다.
결합 후 상태 이미지
M5x12 BOLT를 사용하여 HOUSING COVER와 CMA-U100을 체결한다. M5x12 BOLT를 사용하여 HOUSING COVER와 WMA-U100을 체결한다.
결합 후 상태 이미지 결합 후 상태 이미지
이미지와 같이 위치 시킨 후 HINGE를 사용하여 체결한다.
이미지와 같이 위치 시킨 후 HINGE를 사용하여 체결한다.
3mm Hex Wrench를 사용하여 볼트를 조인다. (4EA 동일 방법)
3mm Hex Wrench를 사용하여 볼트를 조인다. (4EA 동일 방법)
E E
E
E-E-E : ODE-1000T
1
2
HOUSING COVER에 조립한다.
PMA-U100/CMA-U100
This guide illustrates how to assemble the corner mount adapter and
pole mount adapter.
Check the letter of the alphabet assigned to each adapter and tighten
the screws in the corresponding holes to assemble the adapter.
A-A-A(M4 PAM)
IPN6802HD
B-B-B(M4 PAM)
IPN6702HD
C-C-C-C(M5 PAM)
IPN6602HD
D-D-D(M6 PAM)
ODE-1000T
E-E-E-E(M6 PAM)
WMB-3000P & CMB-3000P
F-F-F-F(M5 PAM)
JBK-U100
PMA-U100/CMA-U100
This guide illustrates how to assemble the corner mount adapter and
pole mount adapter.
Check the letter of the alphabet assigned to each adapter and tighten
the screws in the corresponding holes to assemble the adapter.
A-A-A(M4 PAM)
IPN6802HD
B-B-B(M4 PAM)
IPN6702HD
C-C-C-C(M5 PAM)
IPN6602HD
D-D-D(M6 PAM)
ODE-1000T
E-E-E-E(M6 PAM)
WMB-3000P & CMB-3000P
F-F-F-F(M5 PAM)
JBK-U100
G-G-G-G(M6 PAM)
WMB-3000 & WMB-3000S
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 12
4.1. Setting the Image Attributes
On the camera’s webpage, users can configure the image attributes. The menu of the image
attributes is available at Video Appearance via the path, Setup > Video & Audio > Camera.
The following features can be adjusted: Brightness, Contrast, Saturation, and Sharpness.
For more detailed information, refer to the provided “RIVA Web Interface Manual Full HD
Line”.
All Manual’s and Installation Guides can downloaded from www.rivatech.de homepage.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 13
5. CONNECTIONS
Audio connection
The camera provides a mono audio input and output. Due to low audio output power, an
amplified speaker is recommended for enhanced sound. (Refrain from connecting a
headphone or an earphone directly to the camera)
Mic
Amp Speaker
ETHERNET
MICRO SD
DC12V
DO
DI
1
OutOut
1
VIDEO
C C
In
AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6
ETHERNET
MICRO SD
DC12V
DO
DI
1
OutOut
1
VIDEO
C C
In
AUDIO
+
Reset
SW1 SW2 SW3
SW5 SW6
N / A N / A
N / A N / A
SW1
SW2
SW3
SW4
SW5
SW6
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 14
Sensor (DI) connection
Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor like the
following figures. Settings can be done through the camera's webpage.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Caution
!
Do not exceed the maximum input voltage or relay rate.
Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
Caution
!
Do not exceed the maximum relay rating.
DO
COM
Relay Type
Device
Internal
+3.3V
DI
COM
DI
COM
+
-
Relay Type
Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal
Internal
+
-
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 15
Analog Video Out Connection
Use 75 ohm video coaxial cable to connect to a monitor's analog video input and check the
camera's connection and its image focus at the installation site. Be sure to press the output
configuration button (PAL/NTSC button) to see the video (Refer to 3. PART NAMES to check
the location of the PAL/NTSC button). The factory default is 'no video output'; Press once to
set the video to PAL, and press again to set the video to NTSC. Pressing the button again will go
back to 'no video output' mode, disabling the viewing through the analog video connection.
Note
i
Once the PAL/NTSC button is pressed, the video display lasts for 3 minutes
before it goes back to no video output mode.
LAN connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45) to
connect the device to a hub or a router in the network. When the LAN cable is connected, the
orange LED light will become solid and green LED will blink every 250 millisecond. Refer to
Appendix (B). Power over Ethernet for more details.
Video
GND
Red
Black
Green LED Orange LED
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 16
Power Connection
The camera can be powered from either 12VDC or PoE. If the camera is powered via PoE, refer
to Appendix (B). Power over Ethernet for more details. To operate your camera using 12VDC,
make sure the polarity is correct before connecting the power cable. Incorrect connection may
cause damages to the device.
12V
Red
Black
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 17
6. CONFIGURATION
6.1. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the
device from converting the MAC address’s hexadecimal numbers, which is attached to the
device. Be sure that the device and PC are on a same area network before running the
installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
Generic IP Environment
In case of generic private network environment where IP address 192.168.XXX.XXX are used,
users may view the live streaming images on a web page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal
Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of the device.
3. Web streaming and device configurations are supported through ActiveX program. When the
ActiveX installation window appears, authorize and install the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two sets of hexadecimal numbers to decimal numbers.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 18
Custom IP Environment
IPAdminTool and the manual can download from www.rivatech.de homepage.
IPAdminTool is a management tool, which automatically scans all of the network products for
users to perform administrative tasks, which includes network configurations, firmware update,
device reboot, and device organizations.
To modify the device’s default IP address for customized network area:
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select IP Address; IP Setup window appears.
3. In the IP Setup’s window, information under Local Network information displays the
user/PC’s network area information. Those information need to be incorporated to the IP
Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP Address, which
are to be the unique numbers for the device. Refer to the image above for the setting
4. Click Setup to complete the modification.
PC environment Info
Give new unique IP
address in last two sets
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 19
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web browser.
The default username and password is root / pass.
6.3.1. ActiveX Installation
1. When the browser asks to install the AxUMF software, click Install to proceed.
2. When Setup installation pop-up window appears, click Install to proceed with rest of
installations.
Note
i
Depending on system OS and Internet Explorer version, installation experience
may differ from one another. Figures described above are from Windows 7,
Internet Explorer 9 environment.
More Information
To learn more about using other features of your devices, refer to the manuals as “RIVA Web
Interface Manual Full HD Series” or “VCAsys User Manual (Online Help)”, which is available on
www.rivatech.de homepage.
HD Series RC2103HD-6611 Installation Guide
01-2015-A www.rivatech.de 20
Caution
!
6.2.2. View video using IPAdmin Tool
1. From the IPAdminTools product list, select the device by highlighting it.
2. Right-click the mouse and select Web View.
3. The systems default web browser opens the devices address.
Whether directly accessing the streaming video through typing IP address on a
web page or taking steps through IPAdminTool, the ActiveX is needed to be
installed for the Microsoft® Internet Explorer to have the complete
configuration privileges.
1. Click Setup on the upper right of the web page. The login page is displayed as below.
2. Enter the default user name (root) and password (pass), and then select OK.
3. Click System Options on the left of the Setup page, and then select TCP/IP from the drop-
down menu.
4. Input the data for the IP address configuration, and click the Apply button on the bottom
of the page.
When modifying the IP address, be advised to have the correct Subnet mask and Gateway
ready. To use DHCP, select Obtain an IP address via DHCP.
The default username
and password are:
root and pass.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

Riva RC2103HD-6611 Installation guide

Category
Security cameras
Type
Installation guide
This manual is also suitable for

Riva RC2103HD-6611 is a 5 Megapixel CMOS Image Sensor network camera with a wide view (182°) angle and a Certified ImmerVision Enables Panomorph Lens. It supports H.264 Baseline, Main, High profile(MPEG-4 Part 10/AVC), MJPEG(Motion JPEG) video encoding formats and has two-way Audio Streaming with G.711µLaw. Other key features include:

  • Digital Day/Night
  • Digital WDR
  • Three different view types(Single, Quad, Panorama)
  • Three different Camera Position(Ceiling, Wall, Ground)
  • microSD/SDHC slot
  • Power Over Ethernet (PoE)
  • VCA Presence (Standard)
  • VCA Surveillance (Optional)
  • VCA Pro (Optional)

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI