Dell 1125 Owner's manual

Dell™LaserMulti-Function Printer 1125 User's Guide

About Your Multi-Funtion PrinterFaxing

Setting Up Your PrinterUnderstanding the Software

Paper HandlingMaintenance

PrintingTroubleshooting

CopyingSpecifications

Scanning

Model MFP 1125

Order Toner Cartridges

Dell™tonercartridgesareavailableonlythroughDell.Youcanordertonercartridgesonlineatwww.dell.com/supplies or by phone.

Notes, Notices, and Cautions

Information in this document is subject to change without notice.

©2007DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and Dell Toner Management System are trademarks of Dell Inc.; Pentium is a registered trademark of Intel Corporation; Microsoft,

Windows, Windows Server, MS-DOS, Internet Explorer, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries.

ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR Partner, Dell Inc. has determined that this product meets the ENERGY

STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)

(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS.

252.227-7013 and in applicable FAR provisions: Dell Inc., One Dell Way, Round Rock, Texas, 78682, USA.

July 2007 Rev. A00



Canada

877-501-4803



Colombia

01800-9-155676



Mexico

866-851-1754



Puerto Rico

866-851-1760



Trinidad and Tobago

1-800-805-8035



United States

877-INK-2-YOU

NOTE: If your country is not listed, contact your Dell distributor to order supplies.



Toner cartridge



Part number

1,000 page toner

XP092

2,000 page toner

XP407

Drum

TU031

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

Dell™Multi-Function Printer 1125

User's Guide

Order Toner Cartridges

Order Toner Cartridges

Dell™tonercartridgesareavailableonlythroughDell.Youcanordertonercartridgesonlineatwww.dell.com/supplies or by phone.



Information in this document is subject to change without notice.

©2007DellInc.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and Dell Toner Management System are trademarks of Dell Inc.; Pentium is a registered trademark of Intel Corporation; Microsoft,

Windows, Windows Server, MS-DOS, Internet Explorer, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries.

ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR Partner, Dell Inc. has determined that this product meets the ENERGY

STAR guidelines for energy efficiency.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)

(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS.

252.227-7013 and in applicable FAR provisions: Dell Inc., One Dell Way, Round Rock, Texas, 78682, USA.

July 2007 Rev. A00

Back to Contents Page



Canada

1-877-501-4803



Colombia

1-800-915-4755



Mexico

001 866 851 1754



Puerto Rico

866-851-1760



Trinidad and Tobago

1-800-805-8035



United States

877-INK-2-YOU

NOTE: If your country is not listed, contact your Dell distributor to order supplies.



Toner cartridge



Part number

1,000 page toner

XP092

2,000 page toner

XP407

Drum

TU031

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

 Troubleshooting

Dell™Multi-Function Printer 1125

User's Guide

Clearing Jams in the ADF

Clearing Jams in the Paper Paths

Clearing LCD Error Messages

Troubleshooting

Clearing Jams in the ADF

When a document jams while passing through the Automatic Document Feeder (ADF),

ADF Paper Jam appears on the display.



1. Remove the remaining documents from the ADF.



2. Open the ADF cover and remove the roller as shown.



3. Remove the document by gently pulling it out.



4. Replace the roller and close the ADF cover. Then reload the document into the ADF.

Clearing Jams in the Paper Paths

When a paper jam occurs, a location specific message appears on the LCD display. See the table below to locate and clear the paper jam.

NOTE: To prevent document jams, use the scanner glass for thick, thin or mixed documents.

Operator Panel Message



Location of Jam

Go to

Feed area paper jam

Clear Paper Jam

Paper tray

Paper Feed Jam

Fuser area paper jam

Fuser area

Fuser Area Jam

To avoid tearing the paper, pull the jammed paper out gently and slowly. Follow the steps below to clear jams.



Paper Feed Jam



1. Open and close the front cover. The jammed paper automatically exits the printer.

If the paper does not exit, go to the next step.



2. Remove the paper tray cover.



3. Remove the paper by gently pulling it straight out.

If you cannot see the paper or the paper does not move when pulled, check the fuser area. For more information, see Fuser Area Jam.



4. Insert the paper tray into the printer until it snaps into place.

Printing automatically resumes.



Fuser Area Jam



1. Open and close the front cover. The jammed paper automatically exits the printer.

If the paper does not exit, go to the next step.



2. Gently pull the paper out of the output tray.

Clear Paper Jam

Drum area paper jam

Clear Paper Jam

Drum area

Drum Area Jam

CAUTION: The fuser area is hot. Allow a reasonable amount of cooling time to elapse before opening the rear cover.



3. If you cannot see the paper in the output tray or the paper does not move when pulled, open the rear cover.



4. Pull the jammed paper out directly upward, to avoid tearing the paper on the rear paper guide parts.



5. Close the rear cover.



6. Open and close the front cover.

Printing automatically resumes.



Drum Area Jam



1. Open the front cover and lightly pull the toner cartridge straight out.



2. Remove the paper by gently pulling it straight out.



3. Replace the toner cartridge and close the front cover.

Printing automatically resumes.



Tips for Avoiding Paper Jams

By selecting the correct paper types, most paper jams can be avoided. When a paper jam occurs, follow the steps outlined in Clearing Jams in the Paper

Paths.

l Follow the procedures in Loading Print Media in the Paper Tray. Ensure that the adjustable guides are correctly positioned.

l Do not overload the paper tray. Ensure that the paper is below the paper capacity mark on the inside wall of the paper tray.

l Do not remove the paper from the tray while your printer is printing.

l Flex, fan, and straighten the paper before loading.

l Do not use creased, damp, or curled paper.

l Do not mix paper types in the paper tray.

l Use only recommended print media. See Recommended Paper.

l Ensure that the recommended print side of print media is facing down in the paper tray and facing up in the bypass tray.

l Ensure that the duplex unit is installed correctly.

Clearing LCD Error Messages

The following table lists error messages that the LCD may display.

NOTE: The Status Monitor displays the same errors but in a different format, though the cause and solution are identical. See Using the Dell MFP 1125

Status Monitor for more information.

Display

Likely cause



Suggested solutions

Tray error

Reinsert Input

tray

Paper tray not installed.

Install paper tray.

Engine Comms Error

Printer engine may be damaged or connection

faulty.

Restart printer. If message reappears, call Dell.

No Paper

Add Paper

No paper in trays.

Insert paper. (see Loading Print Media in the Paper Tray)

Paper Jam

Fuse Area

Paper jam in fuser area.

Remove jam (see Fuser Area Jam).

Paper Jam

Drum Area

Paper jam in drum area.

Remove jam (see Fuser Area Jam).

Paper Jam

Feeder Area

Paper jam in feeder area.

Remove jam (see Paper Feed Jam).

Toner Low

Toner 75% depleted.

Toner almost empty. Prepare replacement toner.

Toner Empty

Toner 95% depleted.

Replace toner (see Replacing the Toner Cartridge).

Invalid Toner/ No

Toner Found

Incorrect or empty toner installed.

InstallnewDell™genuinetonercartridge(seeReplacing the Toner Cartridge).

Drum Life Exceeded

The drum life is depleted.

Replace drum cartridge(see Replacing the Drum Cartridge).

Troubleshooting

The following chart lists some conditions that may occur and the recommended solutions. Follow the suggested solutions until the problem is corrected. If the

problem persists, contact Dell.



Paper Feeding Problems

Cover Open

Front cover is open.

Close front cover.

Cover Open - Rear

Cover

Rear Cover is open.

Close rear cover.

Paper Size Error

Paper size mismatch.

Insert correct paper size.

Paper jam

ADF area

Paper jam in ADF.

Clear jam (see Clearing Jams in the ADF).

Scanner module

error

Unspecified scanner error.

Restart printer.

Scan Memory Full

Scanning attempted while no memory

available.

Wait for current print/fax job to complete and retry.

Fax TX Error

No tone or comms error.

Check connections and try again.

Fax RX Error

Check telephone

cable

Fax comms error.

Check connections and try again.

Dial Fail

Dial failed.

Try again.

Memory Full

Attempted to send a fax while the system is

printing a job.

Scanning is stopped and display shows whether or not operator want to start

transmission of correctly scanned pages or abort transmission.

Memory Full

Attempted to receive a fax while the system is

doing a scan job with 1200dpi.

Reception is stopped and transmitter may result in Comm. Error. Operator must

release memory space by clearing printer error for further reception.

Fax Jobs Full

Attempted to enter a new delay fax when the

delay fax list is full.

Release some fax jobs and retry.

Group No. is

assigned

Attempted to add a new group when the

number has already been assigned.

Select an alternate number or delete and replace an existing number.

This Speed Num is

Assigned

Attempted to add a new speed dial no. when

the number has already been assigned

Select an alternate number or delete and replace an existing number.

No. not

Assigned

Attempted to input a speed dial number which

has not been assigned.

Select an alternate number or create speed dial entry and retry.



Condition



Suggested solutions

Paper in the output tray is misaligned or falls

out from the output tray.

l Please check the media packaging for the correct preferred printing side or turn the paper in the input

tray over. For more information, see the instructions on the media packaging.

Paper is jammed during printing.

l Clear the paper jam. See Clearing Jams in the Paper Paths.

Paper sticks together.

l Ensure that there is not too much paper in the paper tray. The paper tray can hold up to 250 sheets of

paper, depending on the thickness of your paper.

l Make sure that you are using the correct type of paper. See Recommended Paper.

l Remove paper from the paper tray and flex or fan the paper.

l Humid conditions may cause some paper to stick together.

Multiple sheets of paper do not feed.

l Different types of paper may be stacked in the paper tray. Load paper of only one type, size and

weight.

l If multiple sheets have caused a paper jam, clear the paper jam. See Clearing Jams in the Paper Paths.

Paper does not feed into the printer.

l Remove any obstructions from inside the printer. See Cleaning the Interior.

l Paper has not been loaded correctly. Remove paper from the tray and reload it correctly.

l There is too much paper in the paper tray. Remove excess paper from the tray.

l The paper is too thick. Use only paper that meets the specifications required by the printer. See

Suggested solutions

The printer does not print.

The printer is not receiving power.

Check the power cord connections. Check the power switch and the power source.

The printer is not selected as the

default printer.

Select Multi-Function Printer 1125 as your default printer in your Windows.

Click Start® Settings® Printers. Right-click the Multi-Function Printer 1125 printer

icon and select Set as Default Printer.

Check the printer for the following:

The front or rear cover is not closed.

l Paper is jammed.

l No paper is loaded.

l The toner cartridge is not installed.

If a printer system error occurs, contact your service representative.

The connection cable between the

computer and the printer is not

connected properly.

Disconnect the printer cable and reconnect it.

The connection cable between the

computer and the printer is defective.

If possible, attach the cable to another computer that is working properly and print a

job. You can also try using a different printer cable.

The printer may be configured

incorrectly.

Check the printer properties to ensure that all of the print settings are correct.

The printer driver may be incorrectly

installed.

Remove the printer driver and then reinstall it; see Uninstalling Software and Installing

Software in Windows respectively.

The printer is malfunctioning.

Check the display message on the operator panel to see if the printer is indicating a

system error.

The printer selects print

media from the wrong

paper source.

The paper source selection in the

printer properties may be incorrect.

For many software applications, the paper source selection is found under the Paper

tab within the printer properties. Select the correct paper source. See Paper Tab.

A print job is extremely

slow.

The job may be very complex.

Reduce the complexity of the page or try adjusting the print quality settings.

The maximum print speed of your printer is 27 PPM for Letter-sized paper.

If you are using Windows 98/Me, the

Spooling Setting may be set

incorrectly.

Click Start® Settings® Printers. Right-click the Multi-Function Printer 1125 printer

icon, click Properties® Details® Spool Settings. Select the desired spool setting.

Half the page is blank.

The page orientation setting may be

incorrect.

Change the page orientation in your application. See Layout Tab.

The paper size and the paper size

settings do not match.

Ensure that the paper size in the printer driver settings matches the paper in the tray.

The printer prints, but the

text is wrong, garbled, or

incomplete.

The printer cable is loose or defective.

Disconnect the printer cable and reconnect. Try a print job that you have already

printed successfully. If possible, attach the cable and the printer to another computer

and try a print job that you know works. Finally, try a new printer cable.

The wrong printer driver was

selected.

Check the application's printer selection menu to ensure that your printer is selected.

The software application is

malfunctioning.

Try printing a job from another application.

The operating system is

malfunctioning.

Exit Windows and reboot the computer. Power the printer off and then back on again.

Pages print, but are blank.

The toner cartridge is defective or out

of toner.

Thoroughly shake the toner. See Redistributing Toner.

If necessary, replace the toner cartridge.

The file may have blank pages.

Check the file to ensure that it does not contain blank pages.

Some parts, such as the controller or

the board, may be defective.

Contact a service representative.

The illustrations print

incorrectly in Adobe

Illustrator.

The setting in the software

application is wrong.

Print the document by selecting Download as Bit Image in the Advanced Options

window of the Graphics properties.



Condition



Suggested solutions

Light or faded print

If a vertical white streak or faded area appears on the page:

l The toner supply is low. You may be able to temporarily extend the toner cartridge life. See Redistributing Toner. If this does

not improve the print quality, install a new toner cartridge.

l The paper may not meet paper specifications; for example, the paper is too moist or too rough. See Recommended Paper.

l If the entire page is light, the print resolution setting is too low or the toner save mode is on. Adjust the print resolution and

turn the toner save mode off. See Graphics Tab.

l A combination of faded or smeared defects may indicate that the toner cartridge needs cleaning. See Cleaning the Interior.

l The surface of the LSU part inside the printer may be dirty. Clean the LSU (see Cleaning the Interior).

Toner specks

l The paper may not meet specifications; for example, the paper is too moist or too rough. See Recommended Paper.

l The transfer roller may be dirty. Clean the inside of your printer. See Cleaning the Interior.

l The paper path may need cleaning. See Maintaining the Drum Cartridge.

Dropouts

If faded areas, generally rounded, occur randomly on the page:

l A single sheet of paper may be defective. Try reprinting the job.

l The moisture content of the paper is uneven or the paper has moist spots on its surface. Try a different brand of paper. See

Suggested solutions

The printer is not working, there is no display and the

buttons are not working.

l Unplug the power cord and plug it in again.

l Ensure that there is power to the electrical receptacle.

No dial tone sounds.

l Check that the phone line is connected properly. See Connecting the Telephone and Fax

Lines.

l Check that the phone socket in the wall is working by plugging in another phone.

The numbers stored in the memory do not dial

correctly.

Make sure that the numbers are stored in the memory correctly. Print a Directory list, referring to

Printing Reports.

The document does not feed into the printer.

l Make sure that the document is not wrinkled and you are putting it in correctly. Check that

the document is the right size, not too thick or thin.

l Make sure that the ADF cover is firmly closed.

Faxes are not received automatically.

l The FAX mode should be selected.

l Make sure that there is paper in the paper tray.

l Check to see if the display shows Memory Full.

The printer does not send.

l Make sure that the document is loaded in the ADF or on the scanner glass.

l Sending should show up on the display.

l Check the other fax machine you are sending to, to see if it can receive your fax.

The incoming fax has blank spaces or is received in

poor-quality.

l The fax machine sending you the fax may be faulty.

l A noisy phone line can cause line errors.

l Check your printer by making a copy.

l The toner cartridge may be empty. Replace the toner cartridge, referring to Replacing the

Toner Cartridge.

Some of the words on an incoming fax are stretched.

The fax machine sending you the fax had a temporary document jam.

There are lines on the documents you send.

Check your scan glass for marks and clean it. See Cleaning the Scanner.

The printer dials a number, but the connection with

another fax machine fails.

The other fax machine may be turned off, out of paper, or cannot answer incoming calls. Speak with

the other machine operator and ask her/him to sort out the problem.

Documents are not stored in the memory.

There may not be enough memory to store the document. If the display shows a Memory Full

message, delete any documents you no longer need from the memory and then restore the

document.

Blank areas appear at the bottom of each page or on

other pages, with a small strip of text at the top.

You may have chosen the wrong paper setup in the user option setting. See Setting the Paper Type

and Setting the Paper Size.



Condition



Suggested solutions

Copies are too light or too dark.

Use the Contrast menu to darken or lighten the background of the copies.

Smears, lines, marks or spots appear on

copies.

l If defects are on the original, select Copy® Contrast to lighten the background of your copies.

l If no defects are on the original, clean the scanner glass and underside of the scanner cover. See

Cleaning the Scanner.

Copy image is skewed.

l Ensure that the original is positioned correctly on scanner glass.

l Check that the copy paper is loaded correctly.

Blank copies print out.

l Ensure that the original is face down on the scanner glass or face up in the ADF.

Image rubs off the copy easily.

l Replace the paper in the paper tray with paper from a new package.

l In high humidity areas, do not leave paper in the printer for extended periods of time.

Frequent copy paper jams occur.

l Fan the stack of paper, then turn it over in the paper tray. Replace the paper in the tray with a fresh

supply. If necessary, check/adjust the paper guides.

l Ensure that the paper is the proper paper weight. 75 g/m2 (20 lb) bond paper is recommended.

l Check for copy paper or pieces of copy paper remaining in the printer after a paper jam has been cleared.

Fewer copies from the toner cartridge

than expected print out.

l Your originals may contain pictures, solids, or heavy lines. For example, your originals may be forms,

newsletters, books, or other documents that use more toner.

l The printer may frequently be powered on and off.

l The scanner cover may be left open while copies are being made.



Common Windows Problems



Back to Contents Page



Condition

Suggested solutions

The scanner does not work.

Make sure that you place the document to be scanned face down from the scanner glass, or

face up in the ADF.

There may not be enough available memory to hold the document you want to scan. Try the

Prescan function to see if that works. Try lowering the scan resolution rate.

Check that the USB cable is connected properly.

Make sure that the USB cable is not defective. If necessary, replace the cable.

Check that the scanner is configured correctly. Check the application you want to use to make

certain that the scanner job is being sent to the correct port.

The unit scans very slowly.

Check if the printer is printing received data. Scan the document after the current job is

completed.

Graphics are scanned more slowly than text.

Communication speed becomes slow in scan mode because of the large amount of memory

required to analyze and reproduce the scanned image.

Message appears on your computer screen:

l Device can't be set to the H/W mode you want.

l Port is being used by another program.

l Port is Disabled.

l Scanner is busy receiving or printing data. When

the current job is completed, try again.

l Invalid handle.

l Scanning has failed.

There may be a copying or printing job in progress. When the current job is complete, try the job

again.

The selected port is currently being used. Restart your computer and try again.

The printer cable may be improperly connected or the power may be off.

The scanner driver is not installed or an operating environment is not set up properly.

Ensure that the port is properly connected and the power is turned on. Then restart your

computer.

Check that the USB cable is properly connected.



Condition



Suggested solutions

File in Use message appears during

installation.

Exit all software applications. Remove all software from the StartUp Group, then restart Windows. Reinstall the

printer driver.

Error Writing to LPTx message appears.

Ensure that the cables are connected correctly and the machine is on.

This message may also appear if bi-directional communication is not turned on in the driver.

General Protection Fault, Exception OE,

Spool32, or Illegal Operation messages

appear.

Close all other applications, reboot Windows and try printing again.

Fail To Print, A printer timeout error occurred

messages appear.

These messages may appear during printing. Just keep waiting until the machine finishes printing. If the

message appears in standby mode or after printing has been completed, check the connection and/or whether

an error has occurred.

NOTE: Refer to Microsoft Windows XP/Vista User's Guide that came with your PC for further information on Windows error messages.

Back to Contents Page

 Specifications

Dell™Multi-Function Printer 1125

User's Guide

Physical Specifications

Printer Specifications

Scanner Specifications

Copier Specifications

Facsimile Specifications

Paper Specifications

Print Media Guidelines

Storing Print Media

Identifying Print Media Sources and Specifications

Physical Specifications

Printer Specifications



Item



Description

Dimensions (tray not extended)

W x D x H

413 x 274.5 x 376 mm (depth measured from front

cover to back cover)

Weight

10 kg (including toner cartridge)

Paper Tray

250 page capacity

Weight: 16 to 24 lb (60 to 90 g/m2)

ADF

30 page capacity

Weight: 55 to 125 g/m2

Paper Output

100 page capacity

Weight: 80 g/m2

USB

USB 2.0 (High Speed) Controller to PC host data flow

Security

Security Cable Lock

Acoustics

Standby: 39 dBA (sound pressure)

Printing: 64 dBA (sound power)

Scanning: 50 dBA

Operator Panel

2 x 16 character LCD supporting 50 characters and

scroll capability

LCD

80 degree viewing cone with backlight

Supported Operating Systems

Windows XP, Windows Vista



Item



Description

Speed

20 ppm (A4, LTR)

Resolution

600 x 600 dpi

Print Language

GDI

Duty Cycle

9000 pages/month

Engine Life

50000 pages

Fuser

Permanent (same as engine)

Warm up Time

20 secs

FPOT

16 secs (warm start)

25 secs (cold start)

Memory (DRAM)

32 Mb

Processor Speed

67 MHz (ARMs) 133 MHz (DSP)

Color Modes

Monochrome, Grayscale

Scanner Specifications

Copier Specifications

Facsimile Specifications



Item



Description

Technology

CIS

Resolution

600 dpi

Scan Modes

Mono, grayscale, Full Color, 256 color

Scan Resolution

75, 150, 200, 300, 600 dpi

ADF Scanning

30 page capacity

Scan Speed

11 ppm

Scan Size

A4, LTR

Warm-up/calibrate Time

10 secs

Zoom

25 to 400%

Scanner Glass Capacity

1 in book capacity

Scan Features

Cloning, N-up

Scan Software

TWAIN-Dell MFP 1125 Scanner, WIA-Dell MFP 1125

Scanner

Nuance PaperPort v11 SE

Scan Support

Scan to application from control panel

Supported File Types

.bmp, .pdf, .tiff, .jpeg



Item



Description

Copy Modes

Mono, Grayscale

Scan Resolution

75, 150, 200, 300, 600 dpi

Print Resolution

600 dpi

Copy Speed

20 ppm - single page, multiple copy

20 ppm - ADF @300 dpi single page, multiple copy

11 ppm - ADF @300 x 300 dpi single page, multiple

copy

Number of Copies

1 to 99

FCOT

20 secs (warm start)

30 secs (cold start)

Zoom

25 to 400%

Lighter/Darker increments

5 (-2 to +2)

Copy Features

ID Copy

Cloning

N-up

Collate



Item



Description

Maximum Modem Speed

33.6K

Single World Wide Solution

Yes

Fax Transmission Speed

3 secs/page

Maximum Fax Resolution

400 dpi

Fax Memory

200 pages

Speed Dial Entries

99

Speed Dial Entry Length

50 characters

Speed Dial Group Entries

10

Number of Entries per Group

30

Paper Specifications



Print Media Sizes and Support



Print Media Supported

Receive Forward to Fax

Yes

Broadcast Fax Support

Yes

Stamped Received Report

Yes

Auto Redial

Yes

Auto Reduction

Yes

Delay Fax

Yes

NOTE: Some paper may meet all of the guidelines in this guide and still not produce satisfactory results. This may be the result of improper handling,

unacceptable temperature and humidity levels, or other variables over which Dell has no control.

NOTE: Before purchasing large quantities of paper, ensure the paper meets the requirements specified in this User's Guide.

NOTE: Please load paper to print on the preferred side if the paper packaging indicates it. Failure to do so may result in paper curl or paper jam.

CAUTION: Using paper that does not meet these specifications may cause problems, requiring repairs. These repairs are not covered by the Dell

warranty or service agreements.



Print Media Size



Dimensions



Paper Tray



Bypass Tray



Duplex Printing

A4

8.27 x 11.7 in.

(210 x 297 mm)

Y

A5

5.83 x 8.27 in.

(148 x 210 mm)

Y

N

A6

4.13 x 5.85 in.

(105 x 148.5 mm)

Y

N

JIS B5

7.17 x 10.1 in.

(182 x 257 mm)

Y

N

ISO B5

6.93 x 9.84 in.

(176 x 250 mm)

Y

N

Letter

8.5 x 11 in.

(215.9 x 279.4 mm)

Y

Legal

8.5 x 14 in.

(215.9 x 355.6 mm)

Y

Executive

7.25 x 10.5 in.

(184.2 x 266.7 mm)

Y

N

Oficio

8.5 x 13.5 in.

(216 x 343 mm)

Y

Folio

8.5 x 13 in.

(216 x 330 mm)

Y

Envelope 7-3/4 (Monarch)

3.875 x 7.5 in.

(98.4 x 190.5 mm)

N

Y

N

Envelope COM-10

4.12 x 9.5 in.

(105 x 241 mm)

N

Y

N

Envelope DL

4.33 x 8.66 in.

(110 x 220 mm)

N

Y

N

Envelope C5

6.38 x 9.01 in.

(162 x 229 mm)

N

Y

N

Envelope C6

4.49 x 6.38 in.

(114 x 162 mm)

N

Y

N

Custom

3 x 5 in. to 8.5 x 14 in.

(76 x 127 mm to 216 x 356 mm)

N

Y

N

NOTE: Please follow the instructions on the paper packaging for a preferred printing side. Printing on the wrong side may cause some paper

misalignment on the paper output tray.



Print Media



Paper Tray



Bypass Tray



Standard Output Tray

Paper

Y

Card Stock

N

Y

Transparencies

N

Y

Labels

N

Y

Dual-web and Integrated Labels

N

Y



Print Media Types and Weights

Print Media Guidelines

Print media refers to paper, card stock, transparencies, labels, and envelopes. Your printer provides high quality printing on a variety of print media. Selecting

the appropriate print media for your printer helps you avoid printing problems.



Paper

For the best print quality, use 75 g/m2 (20 lb) xerographic, long grain paper. Try a sample of any paper you are considering using with the printer before

buying large quantities.

When loading paper, note the recommended print side on the paper package, and load paper accordingly. See Loading Print Media in the Paper Tray and

Using the Bypass Tray for detailed loading instructions.



Paper Characteristics

The following paper characteristics affect print quality and reliability. Use the following guidelines when evaluating new paper stock.



Weight

The printer automatically feeds paper weights from 60 to 105 g/m2 (16 to 28 lb bond) grain long in the Automatic Document Feeder (ADF) and from 60 to 90

g/m2 (16 to 24 lb bond) grain long in the paper tray. Paper lighter than 60 g/m2 (16 lb) may not be stiff enough to feed properly, causing jams. For best

performance, use 75 g/m2 (20 lb bond) long grain paper.

For duplex printing, use 75 to 90 g/m2 (20 to 24 lb bond) paper.



Envelopes

N

Y



Print Media



Type



Print Media Weight

Paper Tray

Print Media Weight

Bypass Tray

Paper

Xerographic or business paper

60-90 g/m2 grain

long

(16-24 lb bond)

60-135 g/m2 grain

long

(16 to 36 lb bond)

Card stock-maximum (grain long). See note below

Index Bristol



120 g/m2 (31 lb)



Tag



120 g/m2 (31 lb)



Cover



135 g/m2 (35 lb)

Card stock-maximum (grain short). See note below

Index Bristol



163 g/m2 (43 lb)



Tag



163 g/m2 (43 lb)



Cover



163 g/m2 (43 lb)

Transparencies

Laser printer



138-146 g/m2

(37-39 lb bond)

Labels-maximum

Paper



163 g/m2

(43 lb bond)



Dual-web paper



163 g/m2

(43 lb bond)



Polyester



163 g/m2

(43 lb bond)



Vinyl



163 g/m2

(43 lb liner)

Integrated Forms

Pressure- sensitive area (must enter the printer

first)



135-140 g/m2

(36-40 lb bond)



Paper base (grain long)



75-135 g/m2

(20-36 lb bond)

Envelopes 100% Cotton Content Maximum Weight- 24

lb

Sulfite, wood-free or up to 100% cotton bonds



75-90 g/m2

(20-24 lb)

NOTE: Grain short is preferred for papers over 163 g/m2 (43 lb bond.

NOTE: Dell recommends using 3M transparencies for the Dell MFP 1125.

NOTE: Please follow the instructions on the paper packaging for a preferred printing side. Printing on the wrong side may cause some paper

misalignment on the paper output tray.

Curl

Curl is the tendency of print media to curve at its edges. Excessive curl can cause paper feeding problems. Curl usually occurs after the paper passes through

the printer, where it is exposed to high temperatures. Storing paper unwrapped in humid conditions, even in the paper tray, can contribute to paper curling

prior to printing and can cause feeding problems.



Smoothness

The degree of smoothness of paper directly affects print quality. If the paper is too rough, the toner does not fuse to the paper properly, resulting in poor print

quality. If the paper is too smooth, it can cause paper feeding problems. Smoothness between 100 and 300 Sheffield points is recommended; however,

smoothness between 150 and 250 Sheffield points produces the best print quality.



Moisture Content

The amount of moisture in the paper affects both print quality and the ability of the printer to feed the paper properly. Leave the paper in its original wrapper

until you are ready to use it. This limits the exposure of the paper to moisture changes that can degrade its performance.



Grain Direction

Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either long grain, running the length of the paper, or short grain, running the

width of the paper.

For 60 to 90 g/m2 (16 to 24 lb bond) paper, grain long fibers are recommended. For papers heavier than 90 g/m2 (24 lb bond), grain short is preferred. For the

bypass tray, 60 to 90 g/m2 (16 to 24 lb bond) paper, grain long fibers are recommended.



Fiber Content

Most high-quality xerographic paper is made from 100% chemically pulped wood. This content provides the paper with a high degree of stability resulting in

fewer paper feeding problems and better print quality. Paper containing fibers such as cotton possess characteristics that can result in degraded paper

handling.



Recommended Paper

To ensure the best print quality and feed reliability, use 75 g/m2 (20 lb) xerographic paper. Business papers designed for general business use may also

provide acceptable print quality.

Always print several samples before buying large quantities of any type of print media. When choosing any print media, consider the weight, fiber content, and

color.

Use only paper able to withstand these temperatures without discoloring, bleeding, or releasing hazardous emissions. Check with the paper manufacturer or

vendor to determine whether the paper you have chosen is acceptable for laser printers.



Unacceptable Paper

The following papers are not recommended for use with the printer:

l Chemically treated papers used to make copies without carbon paper, also known as carbonless papers, carbonless copy paper (CCP), or no

carbon required (NCR) paper

l Preprinted papers with chemicals that may contaminate the printer

l Preprinted papers that can be affected by the temperature in the printer fuser

l Preprinted papers that require a registration (the precise print location on the page) greater than 0.09 in., such as optical character recognition

(OCR) forms

l Coated papers (erasable bond), synthetic papers, thermal papers

l Rough-edged, rough or heavily textured surface papers or curled papers

l Recycled papers containing more than 25% post-consumer waste that do not meet DIN 19 309

l Recycled paper having a weight less than 60 g/m2 (16 lb)

l Multiple-part forms or documents



Selecting Paper

Proper paper loading helps prevent jams and ensures trouble-free printing.

To help avoid jams or poor print quality:

l Always use new, undamaged paper

l Before loading paper, know the recommended print side of the paper you are using. This information is usually indicated on the paper package

l Do not use paper that you have cut or trimmed yourself

l Do not mix print media sizes, weights, or types in the same source; mixing may result in jams

l Do not use coated papers

l Remember to change the paper size setting when you use a source that does not support auto size sensing

l Do not remove trays while a job is printing or Busy is displayed on the operator panel

l Ensure that the paper is properly loaded in the source

l Flex paper back and forth. Do not fold or crease the paper. Straighten the edges on a level surface.



Selecting Preprinted Forms and Letterhead

Use the following guidelines when selecting preprinted forms and letterhead paper for the printer:

l Use long grain papers for best results.

l Use only forms and letterhead printed using an offset lithographic or engraved printing process.

l Choose papers that absorb ink, but do not bleed.

l Avoid papers with rough or heavily textured surfaces.

Use papers printed with heat-resistantinksdesignedforuseinxerographiccopiers.Theinkmustwithstandtemperaturesof180°C(356°F)withoutmeltingor

releasing hazardous emissions. Use inks that are not affected by the resin in toner or the silicone in the fuser. Inks that are oxidation-set or oil-based must

meet these requirements; some latex inks are not appropriate. If you are in doubt, contact your paper supplier.

Preprinted papers such as letterhead must be able to withstand temperatures up to 180C (356F) without melting or releasing hazardous emissions.



Printing on Letterhead

Check with the manufacturer or vendor to determine whether the preprinted letterhead you have chosen is acceptable for laser printers.

Page orientation is important when printing on letterhead. Use the following table for help when loading letterhead in the print media sources.



Selecting Prepunched Paper

Prepunched paper brands differ in the number and placement of holes and in manufacturing techniques.

Use the following guidelines to select and use prepunched paper:

l Test paper from several manufacturers before ordering and using large quantities of pre-punched paper.

l Select paper punched at the paper manufacturer and not drilled into paper already packaged in a ream. Drilled paper can cause jams when

multiple sheets feed through the printer.

l Prepunched paper can include more paper dust than standard paper. Your printer may require more frequent cleaning and feed reliability may not

be as good as that of standard paper.



Transparencies

Try a sample of any transparencies you are considering using with the printer before buying large quantities:

l Usetransparenciesdesignedspecificallyforlaserprinters.Transparenciesmustbeabletowithstandtemperaturesof180°C(356°F)without

melting, discoloring, offsetting, or releasing hazardous emissions.

l To avoid print quality problems, avoid getting fingerprints on the transparencies.

l Before loading transparencies, fan the stack to prevent sheets from sticking together.

l Load one transparency at a time in the bypass tray.

Print Media Source

Print Side

Top of Page – Portrait

Top of Page – Landscape

Paper tray

Face down

Front of tray

Left side of tray

Bypass tray

Face up

Logo enters the printer first

Left side of tray



Selecting Transparencies

The printer is designed to print directly on transparencies manufactured for use in laser printers. Print quality and durability depend on the transparency used.

Always print samples on the transparencies you are considering before buying large quantities.

Checkwiththemanufacturerorvendortodeterminewhetheryourtransparenciesarecompatiblewithlaserprintersthatheattransparenciesto180°C(356°

F). Use only transparencies that are able to withstand these temperatures without melting, discoloring, offsetting, or releasing hazardous emissions.



Envelopes

Load one envelope at a time in the bypass tray. Try a sample of any envelopes you are considering using with the printer before buying large quantities. See

Using the Bypass Tray for instructions on loading an envelope.

When printing on envelopes:

l To achieve the best possible print quality, use only high-quality envelopes that are designed for use in laser printers.

l For best performance, use envelopes made from 75 g/m2 (20 lb bond) paper. You can use up to 90 g/m2 (24 lb bond) weight for the bypass tray

as long as the cotton content is 25 percent or less.

l Use only new, undamaged envelopes.

l Useenvelopesthatcanwithstandtemperaturesof180°C(356°F)withoutsealing,curling,wrinkling,orreleasinghazardousemissions.Ifyou

have any doubts about the envelopes you are considering using, check with the envelope supplier.

l Load an envelope with the flap side down and with the stamp area on the top left side. The end of the envelope with the stamp area enters the

bypass tray first. See Using the Bypass Tray for instructions on loading envelopes.

l Adjust the width guide to fit the width of the envelopes.

l A combination of high humidity (over 60%) and the high printing temperatures may seal the envelopes.

For best performance and to minimize jams, do not use envelopes that:

l Have excessive curl or twist.

l Are stuck together or damaged in any way.

l Contain windows, holes, perforations, cutouts, or embossing.

l Use metal clasps, string ties, or metal folding bars.

l Have an interlocking design.

l Have postage stamps attached.

l Have any exposed adhesive when the flap is in the sealed or closed position.

l Have nicked edges or bent corners.

l Have rough, cockle, or laid finishes.



Labels

The printer is designed to print on many labels manufactured for use with laser printers. These labels are supplied in letter size, A4 size, and legal size sheets.

Labeladhesives,facesheet(printablestock),andtopcoatsmustbeabletowithstandtemperaturesof180°C(356°F)andpressureof25poundspersquare

inch (psi). You should load only one label sheet at a time in the bypass tray.

When printing on labels:

l Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a jam. Partial sheets also contaminate your printer

and your cartridge with adhesive, and could void your printer and cartridge warranties.

l Uselabelsthatcanwithstandtemperaturesof180°C(356°F)withoutsealing,curling,wrinkling,orreleasinghazardousemissions.

l Do not print within 0.04 in. (1 mm) of the edge of the label, of the perforations, or between die-cuts of the label.

l Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least 0.04 in. (1 mm) away

from edges. Adhesive material contaminates your printer and could void your warranty.

l If zone coating of the adhesive is not possible, a 0.125 in. (3 mm) strip must be removed on the leading and driver edge, and a non-oozing

adhesive used.

l Remove a 0.125 in. (3 mm) strip from the leading edge to prevent labels from peeling inside the printer.

l Portrait orientation is preferred, especially when printing bar codes.

l Do not use labels that have exposed adhesive.



NOTE: Dell recommends using 3M transparencies for the Dell MFP 1125.

NOTE: Try a sample of any labels you are considering using with the printer before purchasing a large quantity.

Card Stock

Card stock is single ply, and has a large array of properties, such as the moisture content, thickness, and texture, that can significantly affect print quality. See

Identifying Print Media Sources and Specifications for information on the preferred weight for the grain direction of print media.

When printing on card stock:

l Be aware that preprinting, perforation, and creasing can significantly affect the print quality and cause print media handling or jamming problems.

l Avoid using card stock that may release hazardous emissions when heated.

l Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile

components into the printer.

l We recommend the use of grain long card stock.

Storing Print Media

Use the following guidelines for proper print media storage. These help avoid print media feeding problems and uneven print quality:

l Forbestresults,storeprintmediainanenvironmentwherethetemperatureisapproximately21°C(70°F)andtherelativehumidityis40%.

l Store cartons of print media on a pallet or shelf, rather than directly on the floor.

l If you store individual packages of print media out of the original carton, make sure they rest on a flat surface so the edges do not buckle or curl.

l Do not place anything on top of the print media packages.

Identifying Print Media Sources and Specifications

The following tables provide information on standard and optional sources, including the print media sizes available from the paper size menu, and supported

weights.



Print Media Sizes and Support



Print Media Supported

NOTE: Try a sample of any card stock you are considering using with the printer before purchasing a large quantity.

NOTICE: Within the tables, Y indicates the item is supported, N indicates the item is not supported.

NOTICE: Print Media Sizes in normal style are not supported in the US.

NOTE: If you use a print media size not listed, select the next larger size.



Print Media Size



Dimensions



Paper Tray



Bypass Tray

A4

8.27 x 11.7 in. (210 x 297 mm)

Y

A5

5.83 x 8.27 in. (148 x 210 mm)

Y

A6

4.13 x 5.85 in. (105 x 148.5 mm)

Y

JIS B5

7.17 x 10.1 in. (182 x 257 mm)

Y

ISO B5

6.93 x 9.84 in. (176 x 250 mm)

Y

Letter

8.5 x 11 in. (215.9 x 279.4 mm)

Y

Legal

8.5 x 14 in. (215.9 x 355.6 mm)

Y

Executive

7.25 x 10.5 in. (184.2 x 266.7 mm)

Y

Oficio

8.5 x 13.5 in. (216 x 343 mm)

Y

Folio

8.5 x 13 in. (216 x 330 mm)

Y

Envelope 7-3/4 (Monarch)

3.875 x 7.5 in. (98.4 x 190.5 mm)

N

Y

Envelope COM-10

4.12 x 9.5 in. (105 x 241 mm)

N

Y

Envelope DL

4.33 x 8.66 in. (110 x 220 mm)

N

Y

Envelope C5

6.38 x 9.01 in. (162 x 229 mm)

N

Y

Envelope C6

4.49 x 6.38 in. (114 x 162 mm)

N

Y

Custom

3 x 5 in. to 8.5 x 14 in.

(76 x 127 mm to 216 x 356 mm)

N

Y

NOTE: Please follow the instructions on the paper packaging for a preferred printing side. Printing on the wrong side may cause some paper

misalignment on the paper output tray.



Page is loading ...

Dell 1125 Owner's manual

This manual is also suitable for

Dell 1125 Owner's manual

Related papers

Other documents