INSTRUCTION MANUAL
WriteOnBlackboard.com/55
Retain these instrucons. Failure to follow these safety instrucons could result in re, electric shock, other injury, damage to
Boogie Board Blackboard or other property. Do not use Boogie Board Blackboard for other than intended use. This product is not
intended for use by young children without supervision. Do not aempt to open this product other than to replace the baeries
using the baery cover. Only use AA Alkaline (LR6, AM3) baeries with this product. Non-rechargeable baeries are not to be
recharged. Rechargeable baeries are only to be charged under adult supervision. Rechargeable baeries are to be removed from
the product before being charged. Baeries are to be inserted with the correct polarity. Do not mix types, grades, brands, new,
or used baeries. Replace all baeries at the same me. The supply terminals are not to be short-circuited. Exhausted baeries
are to be removed from product. Remove baeries if product is to be le unused for a long me. Upon disposal of this product,
remove baeries and recycle properly.
This device complies with Part
15 of the FCC Rules. Operaon
is subject to the following two
condions: (1) this device may
not cause harmful interference, and (2) this
device must accept any interference received,
including interference that may cause unde-
sired operaon.
This Class B digital apparatus complies with
Canadian ICES-003.
MAINTENANCE
Use a dry cleaning cloth:
Replaceable AA Baeries (LR6, AM3) :
16002273B
Questions? Need help? Contact us.
support@kentdisplays.com
Technical Support: 1-855-224-0888
(8am - 5pm EST) Assembled in USA
Mounting Instructions:
Before Mounting:
Welcome to Blackboard™
Write:
Clear:
Before first use:
1. Select approximate location for mounting Blackboard
and mark height on wall.
2. Use a level and draw a horizontal line the full width of
Blackboard on the wall (approximately 1307.8 mm / 51.5 in.)
3. Using a stud finder (not included), make a small mark
on the line to identify stud locations.
4. Choose two studs that are at least 32” apart to secure
the two included mounting brackets using the four
included screws. Drill four pilot holes using 3/32” drill bit.
Be sure to keep the two mounting brackets aligned and
level when securing to wall.
5. Carefully slide Blackboard onto the mounting brackets.
6. Using a pencil, make a mark on the wall through the
two boom mounting holes.
7. Remove Blackboard from the wall. Using a ¼” drill bit,
drill a hole on the two corner marks and press the includ-
ed drywall anchors into the holes.
8. Mount and reposition Blackboard so that the wall
anchors are aligned with the two mounting holes.
9. Secure Blackboard directly to the wall using one screw
in each of its two boom corners.
10. Carefully slide each corner cap into position over the
two boom corners until you hear or feel a click.
Insert corner cover inserts into boom two corner
covers. The corner cover insert should be pushed
flat against the corner cover.
Be sure to remove the plastic tab located on the baery
door before use.
Use the included inkless Blackboard™ Marker for an experi-
ence that feels familiar.
A simple press of the Clear Buon clears the Blackboard’s
entire writing surface.
55” (diagonal)
writing surface
wall hangers
clear buon
corner cover
Blackboard™
Marker
magnetic ledge
mounting hole
(screw + anchor included)
mounting hole
(screw + anchor included)
baery door
4 (four) AA baeries
stud
stud
stud
Blackboard™ 55 Doane™ Series
Package Includes: Tools Needed:
(x1) Blackboard™ by Boogie Board® 55
(x1) Blackboard Marker
(x2) Boom-Le/Top-Right Corner Covers
Wall Stud Finder
Level
Phillips No. 2 Screwdriver
(x2) Wall Hangers
(x6) Mounting Screws
(x2) Boom-Right/Top-Le Corner Covers
(x2) Corner Cover Insert
(x2) Drywall Anchor
Drill with 1/4” Drill Bit
3/32” Drill Bit
Pencil
Tape Measure
/
