Premier 119265 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
Shut off water supply at angle stop. Remove
old faucet. Clean sink surface in preparation
for new faucet.
Attach horizontal rod (1) to strap (2) using
clip (3). Insert lift rod (4) into strap and
tighten screw (5). Connect assembly to drain
(6).
Important: After installation is completed,
remove aerator. Turn on water supply and
allow both hot and cold water to run for at
least one minute each. While water is
running, check for leaks. Replace aerator.
5.
3.
2.
6.
4.
1.
INSTALLATION STEPS: Two handle lavatory faucet
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
INSTALLATION
Model Number: 119264 & 119265 & 119266
7.
8.
Place new faucet in position on sink. From
under sink, thread mounting nuts onto
faucet. Tighten mounting nuts.
Making the waterline connections:
Use 1/2 in. I.P.S. faucet connections (2, not
included), or use the coupling nuts (3, not
included) with a 3/8 in. O.D. ball-nose riser
(1, not included). Use wrenches when
tightening. Do not overtighten.
2
1
3
5
1
6
2
4
3
4
Brand Lavatory Faucets
3
8
11
7
10
6
5
4
2
9
1
Remove the stopper (1) and the flange (2). Screw
the brass nut (3) all the way down. Push the plastic
washer (4) and the gasket (5) down. Unscrew the
pivot nut (6) from the pop-up body (7) and remove
the seal washers (8). Take off the spring clip (9)
from the horizontal rod (10). Remove the tailpiece
(11) from the pop-up body (7).
5
1
3
4
2
Apply the silicone to the underside of the flange (2).
Insert the pop-up body (1) into the drain hole from
below sink. Screw the flange (2) into the pop-up body
(1). With the pivot hole (3) facing toward faucet, Use
groove joint pliers to tighten the nut (4), do not over
tighten. Do not turn the pop-up while tightening the
nut, or sealant may not seal drain. Clean excess
putty.
Apply thread sealant tape to the top threads of
the tailpiece (5) in a clockwise direction, as shown
and hand tighten.
4
1
2
3
Install the horizontal rod (2) and the stopper (3) as
shown (4). Hand tighten the pivot nut (1).
Tools:
Adjustable wrench
Groove joint pliers
Pipe wrench
Screwdriver
Thread sealant tape
Basin wrench
Plumber's putty
119264 & 119265 & 119266
Handle Assembly
Cartridge(H)
Mounting Nut
Aerator
Bonnet Nut
Washer
Inverter
Handle Screw & Screw Cap (C)
Handle Screw & Screw Cap (H)
Cartridge(C)
Brass Pop-Up
Lift Rod & Lift Knob
MODEL NO.119264
1
9
308
10
1
4
88
7
3
8
1
1
4
6
5
1
1
42
41
1 82 1
3
2 1
185
79
NO. PART DESCRIPTION QTY.PART NO.
11
994599
124020
46
1
1
1
Brass Pop-Up
Lift Rod & Lift Knob
Mounting Nut
Cartridge(C)
Cartridge(H)
10
11
8
Aerator
9
7
124011
994602
1
1
46
1
309
1
4
3
1
1
Washer
Bonnet Nut
Inverter
Handle Assembly
Handle Screw & Screw Cap (C)
Handle Screw & Screw Cap (H)
PART DESCRIPTION
1
4
5
6
2
3
NO.
83 1
88
1
42
41
1
1
86
80
1
1
PART NO.
MODEL NO.119265
QTY.
11
10
2
1
3
4
5
7
6
8
9
PART NO.
8
Aerator
353
Brass Pop-Up
Lift Rod & Lift Knob
10
11
332
354
Mounting Nut
9
46
42
Washer
6
Cartridge(C)
Cartridge(H)
7
4
3
Bonnet Nut
Inverter
4
5
88
41
341 1
Handle Screw & Screw Cap (H)
Handle Assembly
Handle Screw & Screw Cap (C)
2
3 342
340
PART DESCRIPTIONNO.
MODEL NO.119266
1
1
1
1
1
1
1
1
1
1
1
1
QTY.
www.premierfaucet.com, [email protected]
-
1
-
2
Premier 119265 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Design House 545657 Installation guide
-
-
-
-
-
-
-
-
-