SciCan statim 5000 G4 User manual

SciCan
Brand
SciCan
Model
statim 5000 G4
Type
User manual

This manual is also suitable for

STATim 2000/5000 G4
CASSETTE AUTOCLAVE
™
95-112373 Rev. 7.0 Operator’s Manual ST2000/5000 G4. Copyright 2014 SciCan Ltd. All rights reserved.
•
  Operator’s Manual
•
  Manuel de l’utilisateur
•
  Manuale per l’operatore
•
  Manual del Operador
•
  操作手册
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 1 2014-04-25 12:54 PM
Page 2
Contents
1. Introduction ........................................... 4
2. Important Information ........................... 5
2.1 Disclaimers
Drying Performance
2.2 Unit Overview - STATIM 2000 G4
2.3 Unit Overview - STATIM 5000 G4
2.4 Touchscreen Overview
2.5 Set-Up Menu Overview
3. Setting up your STATIM ..................... 11
3.1 Positioning and Powering your Unit
3.2 Levelling your Unit
3.3 Connecting the Waste Bottle
3.4 Filling the Water Reservoir
3.5 Priming the Pump
3.6 Setting the Time
3.7 Setting the Date
3.8 Setting the Language
3.9 AssigningtheUnitIdentierNumber
3.10 Creating a User ID and PIN
3.11 Setting Up Process Enforced Usage
3.12 Changing the Touchscreen
Display Themes
3.13 Adjusting the Screensaver Delay
3.14 Adjusting the Screen Contrast
3.15 Turning the Button Sound ON or OFF
3.16 Adjusting the Button Beep Volume
3.17 Setting up and Using your
STATIMG4WebPortal
3.18 Connecting to a Network
3.19 Connecting to a Wireless Network
3.20 Reserving an IP Address
for your STATIM
3.21 Preparing Unit for Use
4. Using Cassettes
and Preparing Instruments ................ 22
4.1 Using the STATIM 2000 G4 Cassette
4.2
Using the STATIM 5000 G4 Cassette
4.3
Using Drying Plates with
the STATIM 5000 G4
4.4
Preparing and Loading Instruments
4.5
Using Biological and Chemical Indicators
4.6
Instrument Weight Guide
5. Using your STATIM ............................. 28
5.1 Selecting a Cycle
5.2
Running a Cycle
5.3
Stopping a Cycle
6. Storing and Retrieving
Cycle Information ................................ 36
6.1 Retrieving Cycle Information Using
the Touchscreen
6.2
Retrieving Cycle Information Using
the USB Data Back Up
6.3 Cycle Printout Overview
7. Retrieving a Remote Access Code ... 39
8. Printing Cycle Information ................. 40
8.1 Connecting to a Printer
8.2
Adjusting your Print Settings
8.3
ExternalPrintersandSpecications
9. Maintaining your STATIM ................... 41
9.1 Cleaning the Cassette
9.2
Cleaning the Water Reservoir Filter
9.3
Cleaning the Water Reservoir
9.4
Cleaning the Exterior Surfaces
9.5
Changing the Air Filter and the Bacteria
Retentive Filters
9.6
Replacing the Cassette Seal
9.7
Maintaining Fluid Levels
9.8
Reading Water Quality
9.9
Using On-Screen Instructions
9.10
Preventative Maintenance Schedules
9.11
Shipping the Unit /
Draining the Reservoir
10. Troubleshooting your STATIM .......... 47
11. Test Protocols ..................................... 51
12. Ordering Spare Parts .......................... 53
13. Warranty .............................................. 54
14. Specications  ...................................... 55
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 2 2014-04-25 12:54 PM
Page 3
STATIM Cassette Autoclave and STATIM are registered trademarks and
STAT-DRI, Your Infection Control Specialist, and DriTec logos are trademarks of
SciCan Ltd. All other
trademarks referred to in this manual are the property of their
respective owners.
For all service and repair inquiries:
In Canada 1-800-870-7777
United States: 1-800-572-1211
Germany:
+49 (0)7561 98343 - 0
International: (416) 446-4500
Email: [email protected]
Manufacturedby:
SciCan
1440 Don Mills Road,
Toronto ON M3B 3P9
CANADA
Phone: (416) 445-1600
Fax: (416) 445-2727
Toll free: 1-800-667-7733
EU Representative
SciCanGmbH
Wangener Strasse 78
88299 Leutkirch
GERMANY
Tel.: +49 (0)7561 98343 - 0
Fax: +49 (0)7561 98343 - 699
SciCan Inc.
701 Technology Drive
Canonsburg,PA15317
USA
Phone: +1 724 820 1600
Fax: +1 724 820 1479
Toll free: 1-800-572-1211
SciCan Medtech
Alpenstrasse 16
CH-6300ZUG
SWITZERLAND
Phone: +41 (0) 41 727 7027
Fax: +41 (0) 41 727 7029
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 3 2014-04-25 12:54 PM
Page 4
1 Introduction
Congratulations on selecting the STATIM
®
Cassette Autoclave. The STATIM is a compact,
countertopunitthatissuitableforsteamsterilization.ThisSTATIM G4 Cassette Autoclave
is fully compliant with EN13060.
The details of installing, operating and maintaining your STATIM are all contained within
thisoperator’smanual.Pleasereadtheseinstructionsbeforeoperatingthisunitandkeep
them for future reference. Operational, maintenance and replacement instructions should
befollowed.Contentsofthismanualaresubjecttochangewithoutnoticetoreectchanges
and improvements to the STATIM product.
The STATIM issuitableforthesterilizationofdentalandmedicalinstrumentsthatare
validatedtobesterilisedbysteam.RefertotheTestProtocolsectionTypeTestingfor
referenceexamplesofinstrumentsthathavebeenvalidatedintheSTATIM via micro
biologicaltesting.TheSTATIM hasnotbeendesignedtosterilizeliquids,clothloads,
bio-medicalwasteormaterialsnotcompatiblewithsteamsterilization.Theprocessingof
suchloadsmayresultinincompletesterilizationand/ordamagetotheautoclave.
Formoreinformationaboutinstrumentsuitabilityforsteamsterilization,consultthe
instrument manufacturers’ reprocessing instructions.
STATIM 2000 G4
STATIM 5000 G4
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 4 2014-04-25 12:54 PM
Page 5
2.1 Disclaimers
Use only steam-process distilled water in your STATIM.Deionized,demineralized,or
speciallylteredwatershouldnotbeused.Neverusetapwater.
Donotpermitanypersonotherthancertiedpersonneltosupplyparts,serviceor
maintain your STATIM.SciCanshallnotbeliableforincidental,specialorconsequential
damagescausedbyanymaintenanceorservicesperformedontheSTATIM byathirdparty,
orfortheuseofequipmentorpartsmanufacturedbyathirdparty,includinglostprots,
any commercial loss, economic loss, or loss arising from personal injury.
Neverremovethecoveroftheunitandneverinsertobjectsthroughholesoropenings
inthecabinetry.Doingsomaydamagetheunitand/orposeahazardtotheoperator.
IMPORTANT:Followlocalguidelinesgoverningvericationofthesterilizationprocedure.
Drying Performance
The STATIM 2000G4and5000G4havebeendesignedtoprovideacompletesterilization
solutionforyourunwrappedandwrappedinstrumentneeds:rapidsterilizationbalancedwith
rapiddrying,byusingtheSciCanDri-TecDryingTechnology.
The STATIM 2000G4usesconvectionheattodryinstrumentsbyutilizingtheremainingheat
inthesystemafterthesterilizationphase.Heatiscapturedandreleasedinthecassette
to rapidly dry a properly loaded STATIM cassette.
The STATIM 5000G4usesheatgeneratedbythesterilizationphasewhichisabsorbedby
the drying plates. The heat is transferred from drying plates directly to the load resulting
in accelerated, rapid drying of a properly loaded STATIM cassette.
Please refer to this operator’s manual for instructions on the proper arrangement
of instruments in the cassette and the use of drying plates (STATIM 5000 G4). By carefully
followingthesedirectionsonhowtoproperlyloadthecassettechamber,rapiddryingof
theloadwillbeachieved.
2 Important Information
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 5 2014-04-25 12:54 PM
Page 6
2 Important Information 2000 G4
Thefollowingsymbols
appear in the margins
ofthisbook.
Thefollowingsymbolsappearontheunit:
2.2 STATIM 2000 G4 — Unit Overview
When you receive your STATIM 2000G4,theitemslistedbelowwillbeincluded.
If any of the items are missing, contact your dealer immediately.
n
1
LCD touchscreen
n
1
reservoir cap/
n
1
waterlter
n
1
USB port
n
1
power switch
n
1
powercableport
n
1
leveler feet
n
1
Ethernet port
n
1
exhausttubeport
n
1
compressor
n
1
cassette
n
1
biologicallter
n
1
RS232 port
Cassette Tray and Lid
Waste Bottle
Instrument Rack
Bottle Lid Fitting
Operator’s Manual
Exhaust Tube
STAT-DRI PLUS
Tube Mounting Hardware
Power Cord
USB Memory Stick
Figure 1
im  
   

IM
P.C.D. + 20 SciCan
Sterilization Emulators
Apotentialhazard
to the operator.
A situation which
may lead to a
mechanical failure.
Important
information
Caution:HotSurface
and/orHotSteam
Caution: Risk of electrical
shock. Disconnect supply
beforeservicing.
Caution: Refer to manual
for details
Steam distilled water only
1
1
2
2
3
3
4
5
5
6
6
7
8
9
10
10
11
9
12
12
7
11
8
4
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 6 2014-04-25 12:54 PM
Page 7
2 Important Information 5000 G4
Cassette Tray and Lid
Unwrapped
Instrument Rack
Waste Bottle
Bottle Lid Fitting
Power Cord
Operator’s Manual
Exhaust Tube
STAT-DRI PLUS
Tube Mounting Hardware
Rack with Drying Plates
USB Memory Stick
P.C.D. + 20 SciCan
Sterilization Emulators
Thefollowingsymbols
appear in the margins
ofthisbook.
Thefollowingsymbolsappearontheunit:
Apotentialhazard
to the operator.
A situation which
may lead to a
mechanical failure.
Important
information
Caution:HotSurface
and/orHotSteam
Caution: Risk of electrical
shock. Disconnect supply
beforeservicing.
Caution: Refer to manual
for details
Steam distilled water only
When you receive your STATIM 5000G4,theitemslistedbelowwillbeincluded.
If any of the items are missing, contact your dealer immediately.
n
1
LCD touchscreen
n
1
reservoir cap/
n
1
waterlter
n
1
USB port
n
1
power switch
n
1
powercableport
n
1
leveler feet
n
1
exhausttubeport
n
1
biologicallter
n
1
cassette
n
1
RS232 port
n
1
Ethernet port
Figure 2
1
1
2
2
3
3
4
5
5
6
6
7
8
9
10
10
11
11
7 8
9
4
2.3 STATIM 5000 G4 — Unit Overview
im 
  

IM
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 7 2014-04-25 12:54 PM
Page 8
2.4 Touchscreen Overview
mm/dd/yyyy hh:mm:ss
SELECT A CYCLE
Wrapped cycles
Hollow Unwrapped cycles
Rubber / Plastic cycles
Air Dry Only
Start
button
Settings and unit
information
Cassette properly inserted
Water level
and quality status
Network connectivity on/off
(turns green when active)
Display
Figure 3
Stop
button
USB storage device
connected/not connected
(turns green when active)
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 8 2014-04-25 12:54 PM
Page 9
2.5 Set Up Menu Overview
STATIM 5000 S5S2R700
Model: G4-152302
S/N: 000000A00000
CYCLE NUMBER: 1
IF: SL00R100
CF xx
WATER QUALITY IS
NOT ACCEPTABLE
mm/dd/yyyy hh:mm:ss
SELECT A CYCLE
Time
1 2 3
4 5 6
7 8 9
CL 0 EN
--:--
24H
14:02
Date
--/--/--
DD/MM/YY
01/01/2011
1 2 3
4 5 6
7 8 9
CL 0 EN
On
Default Off
DST On/Off
Yyyy/mm/dd xxxxx OK
Yyyy/mm/dd xxxxx OK
Yyyy/mm/dd xxxxx OK
Yyyy/mm/dd xxxxx OK
Yyyy/mm/dd xxxxx OK
Yyyy/mm/dd xxxxx (CFxx)
Yyyy/mm/dd xxxxx (CFxx)
Yyyy/mm/dd xxxxx (CFxx)
Yyyy/mm/dd xxxxx (CFxx)
Yyyy/mm/dd xxxxx (CFxx)
12
Default 24
12h/24h Setup
MM/DD/YYYY
Default DD/MM/YYYY
Date Format
French
Default English
Language
Unit No
1 2 3
4 5 6
7 8 9
CL
0
EN
000
xx.x uS
xx.x ppm
WATER LEVEL
STATIM 5000 S5S2R700
Model: G4-152302
S/N: 000000A00000
CYCLE NUMBER: 1
IF: SL00R100
CF xx
WATER QUALITY IS
NOT ACCEPTABLE
Serial Printer
Default No Printer
Printer type
1200
Default 9600
Baud rate
Setup
Time
Date
DST On/Off
Setup
Time
Date
DST On/Off
Setup
Time
Date
DST On/Off
Setup
Time 12/24
Date Format
Recent Printouts
Setup
Time 12/24
Date Format
Recent Printouts
Setup
Time 12/24
Date Format
Recent Printouts
Setup
Unit No
Water Quality
Language
Setup
Unit No
Water Quality
Language
Setup
Unit No
Water Quality
Language
Setup
Printer Type
Baud Rate
Serial Number
Setup
Printer Type
Baud Rate
Serial Number
Setup
Printer Type
Baud Rate
Serial Number
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 9 2014-04-25 12:54 PM
2.5 Set Up Menu Overview con’t2.5 Set Up Menu Overview con’t
Printer user ° char
1 2 3
4 5 6
7 8 9
CL
0
EN
000
CR
Default -
End of line CR/LF
ON
Default OFF
Process Enforced
PIN Setup
1 2 3
4 5 6
7 8 9
CL
0
EN
0000
User x
PIN Updated
New PIN xxxx
OK
Statim Silver
Default Statim NG
Themes
Upgrade Theme
Upgrade
Upgrade Theme
Upgrade
PLEASE WAIT
Looking for Theme …
Upgrade Theme
Upgrade
P04_B091!
P04_B092!
P04_B093!
P04_B094!
Done!
Setup PIN
Themes
Change Theme
Upgrade Theme
Setup
Printer user ° char
Process Enforced
End of Line CR/LF
Setup
Printer user ° char
Process Enforced
End of Line CR/LF
Setup
Printer user ° char
Process Enforced
End of Line CR/LF
Setup
Themes
Screensaver
User
Setup
Themes
Screensaver
User
OFF
Default ON
Automatic IP (DHCP)
DHCP
LINK: OFF
Bind: dhcp
IP: 0.0.0.0
Renew IP
Renew IP
3 min
Default 2 min
Screensaver
xx
Default 100
LCD Contrast
Network Settings
Automatic IP (DHCP)
Renew IP
Setup
Themes
Screensaver
User
Setup
Network Setup
Button Beep
LCD Contrast
Setup
Network Setup
Button Beep
LCD Contrast
OFF
Default ON
Button Beep
80
Default 100
Beep Volume
Setup
Network Setup
Button Beep
LCD Contrast
Setup
Level
Beep Volume
Setup
Level
Beep Volume
Page 10
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 10 2014-04-25 12:54 PM
Page 11
3 Setting up your STATIM
3.1 Positioning and Powering your Unit
Positioning your Unit
There are several factors that may affect the performance of your STATIM. Please review
thesefactors,andselectasuitablelocationinwhichtoinstalltheunit.
•
Temperature and Humidity
Avoid installing your STATIM in direct sunlight or close to a heat source (e.g. vents or
radiators).Therecommendedoperatingtemperaturesare15-25˚Cwithhumidityof25-70%.
•
Spacing
The vents and openings on your STATIM shouldremainuncoveredandunobstructed.
Leaveaminimumof50mmbetweenthetop,sidesandbackoftheunitandanywall
orpartition.Formoredetailedinformationonclearances,seeSpecications.
•
Venting
Your STATIM shouldbeoperatedinaclean,dustfreeenvironment.
•
Work Surface
Your STATIM shouldbeplacedonaat,level,water-resistantsurface.
Never install and operate the unit on a sloped surface.
•
Electromagnetic Environment
Your STATIM hasbeentestedandmeetsapplicablestandardsforelectromagnetic
emissions.Whileyourunitdoesnotemitanyradiation,itmayitselfbeaffectedbyother
equipmentwhichdoes.Werecommendthatyourunitbekeptawayfrompotentialsources
of interference.
•
Electrical Connection
To power your unit, use properly grounded and fused power sources with the same voltage
ratingasindicatedonthelabelatthebackofyourSTATIM. Avoid multiple outlet receptacles.
Ifusingasurgesuppressorpowerbar,connectonlyoneSTATIM to it.
Powering your Unit
To power your STATIM,connectthepowercordtotheA.C.inletreceptacleatthebackof
the unit. Ensure the power switch is in the OFF position and connect the unit to your
power source.
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 11 2014-04-25 12:54 PM
Page 12
3 Setting up your STATIM
3.2 Levelling your Unit
Whenplacingyourunitonacountertop,ensureitisstableandthatallfourfeetaresecurely
in contact with the counter surface. This will prevent the unit from moving freely. Next, use
thelevelindicatorbubblefunctioninthesettingsmenutoadjustthethreelevelerfeetsothat
theunitdrainsproperly.Toaccessthelevelindicatorbubblefromthemainscreen,follow
these steps:
1.
2. Scroll to
Level
and select.
3. Adjustthelevelerfeettomovethebubble.
Positionthebubbleinthebottomrightquadrant
of the target. This will ensure that the unit drains
properly. Press STOP to exit and return to
the cycle select menu. When the unit is properly
leveled,thebubblelevelwillchangefromred
to green.
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 12 2014-04-25 12:54 PM
Page 13
3 Setting up your STATIM
3.3 Connecting the Waste Bottle
Thewastebottle
1
isusedtocollectthewastewaterafterithasbeenconvertedtosteam
andthendrainedfromthecassette.ToconnectthewastebottletotheSTATIM, follow
these steps (see Figure 4):
1. Insert the exhaust
2
tubeinto
thetting
3
onthebackoftheunit
andpullgentlytoconrmatightt.
2. Cutthetubetolengthandslide
thewastebottletting
4
into place.
3. Placethefreeendofthetubeinto
theholeinthelidofthewastebottle
andhand-tightenthetting.
Donotcoiltheexhausttube.
4. Unscrew the lid and copper condenser
coil
5
assemblyfromthewastebottle.
The lid and coil should come
out together.
5. Fillthewastebottlewithwaterto
the MIN line and replace the lid and
coppercondenserassembly.
Emptythewastebottleoftentoavoid
unpleasant odors and discoloration of
the contents. (A low-level disinfectant,
prepared according to the manufacturer’s
instructions,maybeaddedtothewaste
bottletoremedythissituation).Asa
minimum,emptythewastebottleeach
timeyourellthereservoir.
6. Placethewastebottleneartheunit.
Storethebottlebelowtheunit.
Thetubecanberoutedthroughahole,
(8 mm in diameter) in the countertop
and secured with the provided
nylon clamps.
5000 G4
2000 G4
1
1
2
2
3
3
4
5
5
Figure 4
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 13 2014-04-25 12:54 PM
Page 14
3 Setting up your STATIM
3.4 Filling the Water Reservoir
Whenllingthereservoir,ensureyouonlyusesteamprocesseddistilledwatercontaining
less than 5 ppm total dissolved solids (having conductivity of less than 10 µS / cm).
The impurities and additives in other water
sources will cause an error reading on the LCD.
Tollthereservoir,followthesesteps
(see Figure 5):
1. Remove the reservoir cap
1
.
2. Pour steam-process distilled water into the
reservoir until almost full (a maximum of 4L).
Use a funnel to avoid spillage.
3. Replace and secure the cap.
3.5 Priming the Pump
To prime the STATIM pump, follow these steps:
1. Move the unit to the edge of the work
surface.Thefrontlevelerfeetshouldbe
approximately 12 mm from the edge.
2. Lift the front left corner of the unit upward
andremovethedraintube
2
from the clip
located on the underside of the unit.
3. Pullthedraintubeoutwardsothefreeend
canbepositionedoverawatercontainer.
4. Fill the reservoir with steam-process distilled water.
5. Removetheplug fromtheendofthedraintubeandallowwatertodrainfromthe
tubeintoacontainerfor30seconds.Whenthewaterowsinasteadystream,replace
the stopper.
6. Liftthefrontleftcorneroftheunitupwardandreinsertthetubeintothecliponthe
undersideoftheunit.Pushtheexcesslengthoftubingbackintothespaceprovided.
Makesurethepluginthedraintubeissecure.
Figure 5
1
Figure 6
2
3
3
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 14 2014-04-25 12:54 PM
3.6 Setting the Time
1.
2. Scroll to
Time
and select.
3. From the TIME screen, use the keypad to set the time. Press
EN
to save and
to return to the Setup menu.
4. To change your unit to display 12-hour time format (24-hour time format is the default
setting), go to the Setup menu and use
to scroll to TIME 12/24, select it and
toggle to 12. Press
to save and return to the Setup menu.
5. To activate daylight savings time (DST), which is recommended if you have connected
your unit to a network, go to the Set up menu and use
to scroll to DST ON/OFF
and select. Use
to toggle DST ON or OFF and press to save and return to the
Setup menu.
3.7 Setting the Date
1.
2. Scroll to
Date
and select.
3. From the DATE screen, use the keypad to set the date. Press
EN
to save and
to return to the Setup menu.
4. To change the format in which the date appears, return to the Setup menu and use
to scroll to DATE FORMAT. Select it, and follow the prompts to have
the date displayed in the desired format. Press
to save and return to
the Setup menu.
3.8 Setting the Language
ThemessagesdisplayedbyyourSTATIM canbepresentedinanumberofdifferent
languages. To change the current language, follow these steps:
1.
2. Scroll to
Language
and select.
3. From the LANGUAGE screen, press to scroll through the list of languages.
When you have found the desired language, press
to save your selection and return
to the Setup menu.
Page 15
3 Setting up your STATIM
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 15 2014-04-25 12:54 PM
3.9  Assigning Unit Identier Number
1.
2. Scroll to
Unit No
and select.
3. Usingthekeypad,selectamaximumof3digitstobeusedastheunit’sidentiernumber.
Press
EN
to save and to return to the Setup menu.
3.10 Creating a User ID and PIN
1.
2. Scroll to
User
and select.
3. From the SETUP PIN screen, you can assign up to four PINs. Select one of
the User icons to assign a PIN.
4. Using the keypad, assign a PIN of up to four digits and press
EN
to save and
tomovetotheconrmationscreen.
5. Ifalloftheinformationpresentedintheconrmationscreeniscorrect,pressOK
tobereturnedtothePINUSERscreen.Tomakeacorrection,selectthePINUseryou
wanttochangeandrepeattheprocessdescribedabove.
3.11 Setting Up Process Enforced Usage
Whenprocessenforcedusageisactivated,usersarerequiredtoenteraPINbothatthe
beginningandattheendofacycle.ForProcessEnforcedusagetofunction,UserIDsand
PINsmustrstbeassigned.TosetupUserIDandPINs,refertosection3.10Creatinga
User ID and PIN. To activate process enforced usage, follow these steps:
1.
2. Scroll to
Process Enforced
and select.
3. Use to toggle Process Enforced function ON or OFF. Press
to save your selection and return to the Setup menu.
NOTE: Any user can stop a cycle and remove the cassette even with Process Enforced
usageON.However,thecycledatawillrecordthatanunauthorizeduserhasstopped
the cycle and/or removed the cassette.
Page 16
3 Setting up your STATIM
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 16 2014-04-25 12:54 PM
3.12 Changing the Touchscreen Display Themes
Your STATIM G4touchscreenthemes(i.e.,iconsandbackgroundcolours)canbechanged
tooneofthepresetoptionsoryoucanuploadadditionalthemes,astheybecomeavailable
from SciCan, using the USB port. To change themes follow these steps:
1.
2. Scroll to
Themes
and select.
3. From here, you can either select
Change Theme
for a menu of preloaded themes or
Upgrade Theme
toaccessanewthemethatcanbeloadedusingtheUSBport.
4. In the
Change Theme
screen, use toscrollthroughyouravailableoptions.
As you scroll, each theme will display on the touchscreen. Press
to select your theme
and return to the Setup menu.
5. ToupgradeathemeavailablefromSciCan,downloadthethemeontoyourcomputer’s
desktopandsavethelesontoaportableUSBstoragedevice.Insertthedeviceinto
yourSTATIM’sUSBportand,fromtheUPGRADETHEMEscreen,press
Upgrade
.
5.1 TheunitwillloadthelesdirectlyfromtheUSBstoragedevice.DonotremovetheUSB
storagedevicewhilelesareloading(thiscouldtakeaslongas10minutes).Whenitis
complete,thescreenwilldisplaythe‘Done’message.Thisnewthemewillnowbe
accessiblefromyourTHEMESmenu.
5.2 Press to select this theme and return to the Setup screen.
3.13 Adjusting the Screensaver Delay
Tochangethelengthoftimebeforeyourinactivetouchscreenactivatesthescreensaver,
follow these steps:
1.
2. Scroll to
Screensaver
and select.
3. Use to scroll through your time options. When you have found the amount of time
yourequire,pressit.Press
to save and return to the Setup menu.
Page 17
3 Setting up your STATIM
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 17 2014-04-25 12:54 PM
3.14 Adjusting the Screen Contrast
The STATIM G4touchscreensarecalibratedforthelightingconditionofmoststerilization
centres.Shouldyouneedtoadjustthecontrastforyourofce,followthesesteps:
1.
2. Scroll to
LCD Contrast
and select.
3. Use to scroll through your contrast options. When you have found the contrast
yourequire,pressit.Press
to save and return to the Setup menu.
3.15 Turning the Button Sound ON or OFF
The STATIM G4ispresettobeepwhenabuttonispressed.Ifyouwouldliketoturn
thebuttonsoundoff,followthesesteps:
NOTE:TurningOFFthebuttonsounddoesNOTturnoffotheralarmsandcyclenotication
beeps.
1.
2. Scroll to
Beep ON/OFF
and select.
3. Use toscrollthroughyourONorOFFoptionsandselectitbypressingit.
Press
tosaveandmovebacktotheSetupmenu.
3.16 Adjusting the Button Beep Volume
Ifyouwouldliketoadjustthebeepvolume,followthesesteps:
1.
2. Scroll to
Beep Volume
and select.
3. Use to scroll through to scroll through the volume settings. Select the one
youwantbypressingit.Press
tosaveandmovebacktotheSetupmenu.
Page 18
3 Setting up your STATIM
Beep ON/OFF
Beep Volume
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 18 2014-04-25 12:54 PM
Page 19
3 Setting up your STATIM
3.17 Setting up and Using your STATIM G4 Web Portal
The STATIMG4webportalisadirectconnectiontotheSTATIM on your local area
network.Itisprotectedbyyourrewallandnotaccessibletooutsideusers(unlesstheyhave
a Remote Access Code. For more information, see Section 7. Retrieving a Remote Access
Code).Thewebportalprovidesreal-timecycleinformationandarchivedsterilizationrecords
uniquetothisunit.Fromhere,youcanprintreports,setupemailnoticationandsearchcycle
histories.Tosetupyourwebportalfollowtheinstructionsavailableontheportal’s‘HELP’tab.
3.18 Connecting to a Network
The STATIMG4hasa10/100Base-TEthernetportlocatedatthebackoftheunit.
To connect your STATIM to a network using a router, follow these steps:
1. ConnectyournetworkcabletotheEthernetportatthebackoftheunit.Ifyourofceuses
a router, the router should automatically assign the unit an IP address. You will know the
IPaddresshasbeenassignedwhentheredXovertheNetworkicondisappears.
NOTE: In some circumstances, where you do not have a router, for example when using
Windows Network Sharing, you may have to assign a dedicated or ‘static’ IP address.
To assign a static IP address, contact your local network administrator.
2. From the main screen, press the Network icon. The Network screen displays information
aboutyourSTATIM’s connectivity, including its IP address.
mm/dd/yyyy hh:mm:ss
SELECT A CYCLE
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 19 2014-04-25 12:54 PM
Page 20
3 Setting up your STATIM
3. TypetheIPaddressdisplayedonthetouchscreenintothebrowserofanywebenabled
devicetoaccessyourunit’swebportal.YouwillknowthatanIPaddresshasbeen
assignedwhentheredXovertheNetworkicondisappears.WhentheNetworkiconis
active (for example when sending email) it will turn green.
NOTE:UseQRcodeifconnectingtoamobiledevice.
NOTE: Connection time will vary depending on your network speed, and making an initial
connection can take longer.
3.19 Connecting to a Wireless Network
The STATIMG4canbeconguredforwirelessusebyconnectingtheEthernetporttoan
externalwirelessbridge/accesspoint.SciCancurrentlyrecommendstheuseoftheD-Link®
DAP-1522XtremeN®DuoWirelessBridge.Contactyournetworkadministratortolearn
moreaboutsettingupawirelessbridge.
3.20 Reserving an IP Address for your STATIM
When your STATIMisconnectedtoarouteronyournetwork,itisassignedauniqueIP
address.IftheconnectionbetweenyourSTATIM and the router is lost (e.g. power fail-
ure, STATIMorrouterwasrestarted),there-establishedconnectionmaybeadifferentIP
address.Thismaycauseanypreviouslysavedbookmarksorothersavedlinkstobecome
invalid.
Toseta‘permanent’IPaddress(alsoknownasestablishingaDHCP/IP/Address
Reservation), follow these steps:
1. Select the Network icon From the STATIMG4touchscreenandwritedownthenumbers
foundfortheGATE(RouterLocalIP).EnterthisGATEnumberintheaddressbarof
yourwebbrowsertoaccessyourroutersettings.(NOTE:Youwillneedyournetwork
password to change the settings.)
mm/dd/yyyy hh:mm:ss
SELECT A CYCLE
95-112373 EU EN R7 STATIM 2000S G4 5000S G4 OpMan 20140422 1945.indd 20 2014-04-25 12:54 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

SciCan statim 5000 G4 User manual

SciCan
Brand
SciCan
Model
statim 5000 G4
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents