Signature SS001N Your Safety & Instruction Manual

Type
Your Safety & Instruction Manual
1000W
MULTIFUNCTION STEAM MOP
MODEL SS001N
YOUR SAFETY &
INSTRUCTION MANUAL
PLEASE READ CAREFULLY
www.signaturebrand.co
2
CUSTOMER SUPPORT TEAM: +44 (0) 333 220 6062
DOCUMENTATION
We declare that this product conforms to the following product legislation in accordance with the
following directive(s):
2014/30/EU Electromagnetic Compatibility Directive.
2014/35/EU Low Voltage Directive.
2011/65/EU Restriction of Hazardous Substances Directive.
RK Wholesale LTD Quality Assurance, United Kingdom
WARRANTY
This product is guaranteed for 12 months from the date of original purchase. If any defect arises due
to faulty materials of workmanship, the faulty products must be returned to the place of purchase.
Refund or replacement is at the discretion of the retailer.
The following conditions apply:
The product must be returned to the retailer with proof of purchase.
The product must be installed and used in accordance with the instructions contained in this
instruction guide.
It must be used only for domestic purposes.
It does not cover wear and tear, damage, misuse or consumable parts.
RK Wholesale LTD has limited liability for incidental or consequential loss or damage.
This guarantee is only valid in the UK and Eire.
An extended warranty is available for this appliance.
See back page for details.
TECHNICAL DATA
Description: Multifunction Steam Mop
Model: SS001N
Rated Voltage: 220-240V ~50Hz
Power Consumption: 1000W
Water Capacity: 240ml Water Tank
3
www.signaturebrand.co
WIRING SAFETY FOR UK USE ONLY
IMPORTANT
As the colours in the
mains lead of this
appliance may not
correspond with the
coloured markings
identifying the terminals
in your plug, please
proceed as follows:
The wires in the mains lead are coloured in
accordance with the following code:
Blue neutral [N] Brown live [L]
Green/Yellow [EARTH]
Plug Fitting Details (Where Applicable).
The wire coloured blue is the neutral and must
be connected to the terminal marked [N] or
coloured black.
The wire coloured brown is the live wire and
must be connected to the terminal marked [L] or
coloured red.
The wire coloured green/yellow must be
connected to the terminal marked with the letter
[E] or marked
.
On no account must either the brown or the blue
wire be connected to the [EARTH] terminal
.
Always ensure that the cord grip is fastened
correctly.
The plug must be tted with a fuse of the same
rating already tted and conforming to BS 1362
and be ASTA approved.
If in doubt consult a qualied electrician who will
be pleased to do this for you.
Non-Rewireable Mains Plug
If your appliance is supplied with a non-
rewireable plug tted to the mains lead and
should the fuse need replacing, you must use an
ASTA approved one (conforming to BS 1362 of
the same rating).
If in doubt, consult a qualied electrician who will
be pleased to do this for you.
If you need to remove the plug – disconnect
it from the mains – and then cut it o of the
mains lead and immediately dispose of it in a
safe manner. Never attempt to reuse the plug or
insert it into a socket outlet as there is a danger
of an electric shock.
WARNING:
This Appliance MUST be Earthed
FUSE
4
CUSTOMER SUPPORT TEAM: +44 (0) 333 220 6062
PRODUCT SAFETY
When using any electrical appliance, basic safety precautions should
always be followed including the following:
Check that the voltage of the
main circuit corresponds with
the rating of the appliance
before operating.
Please ensure that the
appliance is used on a stable,
level, and heat resistant
surface.
DO NOT immerse cords, plugs
or any part of the appliance in
water or any other liquid.
DO NOT leave the appliance
unattended while it is operating.
Close supervision is necessary
when any appliance is used by
or near children or pets.
This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved.
Children shall not play with the
appliance.
Cleaning and user maintenance
shall not be made by children
without supervision.
Switch o at the wall socket
then remove the plug from
the socket when not in use or
before cleaning.
If the supply cord or appliance
is damaged, stop using the
appliance immediately and seek
advice from the manufacturer
or its service agent or a similarly
qualied person.
DO NOT let the cord hang over
the edge of a table or counter
or let it come into contact with
any hot surfaces.
DO NOT pull or carry the
appliance by cord, use cord as
a handle, close a door on the
cord, or pull cord around sharp
edges or corners. Keep cord
away from heated surfaces.
The use of accessory
attachments is not
recommended by the appliance
manufacturer, apart from those
supplied with this product.
DO NOT pull the plug out by
the cord as this may damage
the plug and/or the cable.
DO NOT use this product for
anything other than its intended
use.
This appliance is for household
use only.
DO NOT carry the appliance by
the power cord.
DO NOT use the appliance
outdoors.
Never direct steam towards
people, animals or plants.
5
www.signaturebrand.co
DO NOT handle the plug or the
steam mop with wet hands or
operate without shoes.
DO NOT insert any objects
into openings in the unit and
DO NOT use with any opening
blocked including the steam
output.
DO NOT use the mop head
without the oor cloth or
without water in the water tank.
Use extra caution when using
on stairs as the cable can
become a trip hazard.
DO NOT use hot water or
chemicals (including cleaning
detergents) in the water tank.
The liquid or steam should not
be directed towards electrical
equipment.
Stop using the steam mop if
water leakage is observed, and
contact a qualied electrician to
test and repair the unit.
DO NOT use the steam mop in
enclosed spaces that are lled
with ammable, or explosive or
toxic vapours.
DO NOT use on heat sensitive
materials e.g., leather or waxed
ooring.
DO NOT use for space heating
purposes.
DO NOT touch hot surfaces
with the cable or the product
and allow to it cool before
assembly or disassembly
occurs.
WARNING: On surfaces that
have been treated with wax,
the wax may be removed by
the heat and steam action.
DO NOT use the mop on
unsealed wood oors or let
the unit stand on any wood
oor for an extended period
of time. This could cause the
wood grain to rise. When using
on vinyl, linoleum or any other
heat sensitive oors, use extra
caution. Too much heat can
melt down glue in the ooring.
Therefore, it is recommended
that a sample cleansing be
carried out on an isolated
area of the oor. It is also
recommended that you check
the use and care instructions
of the surface from the oor
manufacturer to ensure
suitability to steam cleaning.
In the unlikely event the
appliance develops a fault,
stop using it immediately and
seek advice from the Customer
Support Team.
HIGH VOLTAGE HOT SURFACE
6
CUSTOMER SUPPORT TEAM: +44 (0) 333 220 6062
BEFORE YOUR FIRST USE:
1. Remove the parts from the packaging.
2. Assemble as instructed in the assembly page.
3. Your appliance is now ready for normal use.
Dispose of the packaging in a responsible manner.
WHAT’S IN THE BOX
Instruction Manual
Steam Mop
Measuring Cup
1. Handle
2. Upper Cable Winder
3. Lower Cable Winder
4. Power Switch (O/I) LED ON/OFF Light
5. Main Body
6. Water Tank Cover
7. Water Tank
8. Lock Button (on main body)
9. Mop Head
10. Microber Cloth Pad
11. Carpet Glider
1
2
3
4
5
6
7
8
9
10
11
7
www.signaturebrand.co
ASSEMBLY
Attaching the Main Body and Handle:
1. Insert the Swivel Joint into designated
hole in the Main Body until it locks in place
with the Lock Button on the Main Body
(you will hear a clicking sound).
2. Connect the body of the handle together
in accordance with the following picture.
Note: Assemble the plastic tubes without the
Cable Winder in the middle. Line each tube up
and insert them into each other.
3. Attach the handle the main body of the
mop by inserting to the top of the plastic
tube. (See opposite)
Attaching the Microfiber Cloth:
1. Place the Microber Cloth Pad onto the
mop head.
2. Fasten the Microber Cloth Pad by pulling
the cord while pressing on the toggle.
Assembling the Carpet Glider:
1. When using Steam Mop on carpets, place
the mop head (with microber cloth) over
the Carpet Glider.
Note: Do not operate without the Microber
Cloth Pad in place.
Filling The Water Tank:
IMPORTANT: Always ensure that the unit is
disconnected from the mains outlet prior to the
initial lling of the water tank, and before tting
the bottom of the mop head.
Never use the steam mop without the
microber cleaning pad securely in place.
1. Turn the cap and then lift it up to remove it
from the water tank.
2. Using the measuring cup, pour one cup of
water into the water tank.
3. Place the cap back on onto the tank.
8
CUSTOMER SUPPORT TEAM: +44 (0) 333 220 6062
USING YOUR APPLIANCE
IMPORTANT: Never use the steam mop without
the microber cleaning pad.
1. Make sure the water tank is lled. Refer to
the Filling the Water Tank section.
2. Plug the power cord into the mains outlet
and move the Power Switch to the On (I)
position. After 20-35 seconds, hold and
press on the handle to emit steam from
the mop.
Note: The mop will only emit steam when the
handle is continuously pressed.
3. Slowly pass over surface to be cleaned.
Note: It’s recommended to sweep or
vacuum oor prior using the Steam Mop.
4. To sanitise a specic area of the oor,
leave the steam mop over the area for a
minimum of 8 seconds, but no longer than
15 seconds.
Note: Leaving the steam mop in a stationary
position for more than the recommended time
may cause a build up of pale residue. The
residue can be removed by using a decalcifying
product or with a few drops of vinegar. (See the
Troubleshooting Guide).
WARNING! NEVER run the steam mop without
water. NEVER direct any steam at any person
or animal. Use the appliance on a sealed hard
oor only.
5. To stop emitting steam, release the handle
and move the Power Switch to the O (O)
position.
6. Unplug the power cord from the mains
outlet and empty the water tank.
CAUTION! Wait for the appliance to cool
before emptying the tank since the water
may be extremely hot.
7. Carefully remove the cloth pad from the
head and wind the power cord around the
Cord Wrap. CAUTION! The cloth pad may
be very hot. Wait until it has cooled before
removing it.
8. Store the appliance upright in a dry area
or hang it using the storage hook.
TROUBLESHOOTING
Problem Possible Cause Solution
The steam mop will not
turn on.
The appliance is not plugged in or
turned on.
Make sure the steam mop is plugged
into the mains outlet and that the power
switch is in the ON (I) position.
Reduced steam or no
steam.
The water tank is empty.
The steam nozzle is blocked.
Limescale deposit.
The handle is not pressed
continuously.
Fill the water tank.
Clean the nozzle.
Refer to the Limescale Removal section.
Press and hold the handle continuously to
emit steam.
The cleaning cloth is
wet.
The cloth gets saturated with water.
Remove the wet cloth and replace with a
new one.
Clean the cloth or allow it to cool, then
wring it out and re-attach.
9
www.signaturebrand.co
CLEANING AND CARE
WARNING! DO NOT IMMERSE THE APPLIANCE IN WATER OR ANY OTHER LIQUID.
Ensure that the steam mop is switched off and
disconnected from the mains outlet before
cleaning.
Limescale:
If you live in a particularly hard water area, we
recommend using bottled or distilled water.
Warning: never pour vinegar or other liquid
cleaners for eliminating calcium into water
tank.
After Using the Steam Mop:
Disconnect power supply, allow the steam
mop to cool completely and empty the
water left in water tank. Let the Steam Mop
completely cool down, clean with a damp cloth
or a nonabrasive (liquid) cleaner.
Decalcify the Water Tank:
To clean calcium deposits that build up inside
the water tank:
1. Add one or two tablespoons of white
vinegar to a full water tank.
2. Close the water tank cap and shake the
contents. DO NOT TURN THE STEAMER
ON.
3. Let the unit sit for a few hours, then
empty the water tank.
4. Refill the tank with clean water and empty
it until it rinses clear.
Limescale Removal:
If your steam mop begins to produce
steam more slowly or completely stops,
you may need to remove limescale from
your appliance.
Limescale can develop over time on the
metal parts and greatly affect the mop’s
performance.
It’s necessary to remove limescale on a
regular basis every 25 to 50 times you
use a full tank of water (or at least once
a month), especially in hard water areas
and how often you use the steam mop.
1. Prepare a solution of 1/3 white vinegar &
2/3 tap water and add to the water tank.
2. Secure and position the unit to ensure
any released steam is aimed away from
the floor or surrounding objects and
surfaces.
3. Plug the steam mop in and turn it ON by
pressing the Power Switch (O/I). Allow
the appliance to produce steam until the
vinegar/water solution is used up.
4. Repeat the above procedures as many
times as necessary, until a normal steam
flow rate is achieved.
5. Fill the Water Tank with fresh water and
rinse it out.
6. Once the tank is empty, fill it again with
fresh water and attach it to the unit.
Release steam through the system until
the Water Tank is empty.
TO STORE YOUR APPLIANCE:
Ensure that the appliance has been
emptied of water and is clean and dry
before you store it.
Store the appliance in a cool and dry
place.
WARNING:
DO NOT IMMERSE ANY PART OF THE
APPLIANCE IN WATER
10
CUSTOMER SUPPORT TEAM: +44 (0) 333 220 6062
NOTES
11
www.signaturebrand.co
DISPOSAL OF THE UNIT
Appliances bearing the symbol shown
here may not be disposed of in domestic
rubbish. You are required to dispose of old
electrical and electronic appliances like this
separately.
Please visit www.recycle-more.co.uk or
www.recyclenow.co.uk
for access to information about the
recycling of electrical items.
Please visit www.weeeireland.ie for access
to information about the recycling of
electrical items purchased in Ireland.
The WEEE directive, introduced in August
2006, states that all electrical items must
be recycled, rather than taken to landfill.
Please arrange to take this appliance to
your local Civic Amenity site for recycling,
once it has reached the end of its life.
NOTES
We hope you enjoy your appliance for many years.
As a thank you for purchasing one of our fantastic products,
we are oering you an extra 1 year peace of mind.
To receive your extra 1 year guarantee, register your appliance online within
28 days of purchase by visiting
www.signaturebrand.co
Should you have a problem
with your appliance or need any spare parts please call our
Customer Support Team: on:
+44 (0) 333 220 6062
Distributed throughout the UK by RK Wholesale LTD
1117.V2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Signature SS001N Your Safety & Instruction Manual

Type
Your Safety & Instruction Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI