H3C LSW1SP2P0 User manual

Brand: H3C

Model: LSW1SP2P0

Category: Network switches

Type: User manual

This manual is also suitable for

H3C LSW1SP2P0 is an optional interface card that provides two 1/10 Gbps SFP+ fiber ports. It connects to another SFP/SFP+ port through an inserted SFP/SFP+ transceiver module and a cable. The H3C LSW1SP2P0 also allows device connection with SFP+ cables provided by H3C. With its high-speed connectivity and flexibility, the H3C LSW1SP2P0 is ideal for expanding the network connectivity options of various devices, enabling efficient data transmission and exchange in demanding network environments.

H3C S5820X & S5800 Series

Ethernet Switches Interface Cards

User Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6PW106-20150306

and its licensors

No part of this manual may be reproduced or transmitted in any form or

by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, ,

H3Care, , IRF, NetPilot, Netflow, SecEngine, SecPath,

SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks

of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any

kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental

protection requirements. The storage, use, and disposal of this product

must meet the applicable national laws and regulations.

Obtaining documentation

You can access the most up-to-date H3C product documentation on the

World Wide Web at http://www.h3c.com

Click the links on the top navigation bar to obtain different categories of

product documentation:

[Technical Support & Documents > Technical Documents]

—Provides

hardware installation, software upgrading, and software feature

configuration and maintenance documentation.

[Products & Solutions]

—Provides information about products and

technologies, as well as solutions.

[Technical Support & Documents > Software Download]

—Provides the

documentation released with the software version.

Technical support

service@h3c.com

http://www.h3c.com

Documentation feedback

You can e-mail your comments about product documentation to

info@h3c.com.

We appreciate your comments.

Contents

Optional Interface Cards ········································································ 1

Introduction to Optional Interface Cards ········································· 1

LSW1SP4P0 ························································································ 3

Front panel ···················································································· 3

SFP+ port status LEDs ···································································· 4

LSW1SP2P0 ························································································ 5

Front panel ···················································································· 5

SFP+ port status LEDs ···································································· 5

LSW1GP16P0 ···················································································· 6

Front panel ···················································································· 6

100/1000Base-X SFP port status LEDs ······································· 6

LSW1GT16P ······················································································· 8

Front panel ···················································································· 8

10/100/1000Base-T auto-sensing Ethernet port LEDs ············· 8

Installing and Removing an Optional Interface Card ························ 11

Installing an Interface Card ···························································· 11

Removing an Interface Card ·························································· 14

Ordering and Installing Transceiver Modules ···································· 16

Ordering a Transceiver Module ···················································· 16

SFP+ transceiver module overview··········································· 16

SFP+ cable overview ································································· 17

SFP transceiver module overview ············································· 19

Installing a Transceiver Module ····················································· 19

Verifying the Installation ······································································· 21

Optional Interface Cards

Introduction to Optional Interface Cards

S5820X Series and S5800 Series Ethernet Switches provide fixed ports

as well as expansion slots for optional interface cards. The interface

card provides an interface so that you can insert a transceiver module

(SFP/SFP+) into the interface and connect it to the interface of another

switch with cables.

Table 1 Optional interface card types

Interface

card type

Applicable to Description

LSW1SP4P

S5800 series

S5820X

series

• Provides four 1/10 Gbps SFP+

fiber ports (see LSW1SP4P0).

• Connects to another SFP/SFP+

port through an inserted

SFP/SFP+ transceiver module

and a cable. For more

information about optional

SFP/SFP+ transceiver modules,

see SFP+ transceiver module

ove

rview and SFP transceiver

module o

verview.

• Allows device connection with

SFP+ cables provided by H3C.

For more information about

SFP+ cables, see SFP+ cable

ove

rview.

Interface

card type

Applicable to Description

LSW1SP2P

S5800 series

S5820X

series

• Provides two 1/10 Gbps SFP+

fiber ports (see LSW1SP2P0).

• Connects to another SFP/SFP+

port through an inserted

SFP/SFP+ transceiver module

and a cable. For more

information about optional

SFP/SFP+ transceiver modules,

see SFP+ transceiver module

ove

rview and SFP transceiver

module o

verview.

• Allows device connection with

SFP+ cables provided by H3C.

For more information about

SFP+ cables, see SFP+ cable

ove

rview.

LSW1GP1

6P0

S5800 series

• Provides sixteen 100/1000

Mbps SFP copper/fiber ports

(see LSW1GP16P0).

• Connects to another SFP port

through an inserted SFP

transceiver module and a cable.

For more information about

optional SFP transceiver

modules, see SFP transceiver

module o

verview.

Interface

card type

Applicable to Description

LSW1GT1

S5800 series

Provides sixteen 10/100/1000

Mbps fiber Ethernet ports

(see LSW1GT16P).

NOTE:

The optional interface cards described in this document are

applicable to many H3C switch models. For the up-to-date

information about the switch models supporting the optional

interface cards, consult H3C marketing staff or technical support.

LSW1SP4P0

Front panel

Figure 1 LSW1SP4P0 front panel

(1) SFP+ port (2) SFP+ port status LED

SFP+ port status LEDs

Each SFP+ port on the LSW1SP4P0 front panel has its own LED, which

indicates the port status, as shown in Figure 2.

Table 2 Description of

SFP+ port status LEDs

LED Status Meaning

SFP+

port

status

LED

Rate

mode

Solid green

The port operates at the rate of

10 Gbps; the LED is fast

blinking when data is being sent

and/or received on the port.

Solid yellow

The port operates at the rate of

1 Gbps only; the LED is fast

blinking when data is being sent

and/or received on the port.

Blinking

yellow (3 Hz)

Power-on self text (POST) failed

on the port.

Off The port has not gone up.

Duple

mode

Solid green

The port operates in full-duplex

mode only; the LED is fast

blinking when data is being sent

and/or received on the port.

Blinking

yellow (3 Hz)

POST failed on the port.

Off The port has not gone up.

LSW1SP2P0

Front panel

Figure 2 LSW1SP2P0 front panel

(1) SFP+ port (2) SFP+ port status LED

SFP+ port status LEDs

Each SFP+ port on the LSW1SP2P0 front panel has its own LED, which

indicates the port status. See Table 2 f

or LEDs description.

LSW1GP16P0

Front panel

Figure 3 LSW1GP16P0 front panel

(1) 100/1000Base-X SFP port

(2) 100/1000Base-X SFP port status LED

100/1000Base-X SFP port status LEDs

Each SFP port on the LSW1GP16P0 front panel has its own LED, which

indicates the port status, as shown in the following table.

Table 3 Description of 100/1000Base-X SFP port status LEDs

LED Status Meaning

100/10

00Base-

X SFP

port

status

LED

Rate

mode

Solid

green

The port operates at the rate of

1000 Mbps; the LED is fast

blinking when data is being sent

and/or received on the port.

Solid

yellow

The port operates at the rate of

100 Mbps only; the LED is fast

blinking when data is being sent

and/or received on the port.

Blinking

yellow (3

Hz)

POST failed on the port.

Off The port has not gone up.

Duple

mode

Solid

green

The port operates in full-duplex

mode only; the LED is fast

blinking when data is being sent

and/or received on the port.

Blinking

yellow (3

Hz)

POST failed on the port.

Off The port has not gone up.

LSW1GT16P

Front panel

Figure 4 LSW1GT16P front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port

(2) 10/100/1000Base-T auto-sensing Ethernet port LED

10/100/1000Base-T auto-sensing Ethernet port LEDs

Each Ethernet port on the LSW1GT16P front panel has its own LED,

which indicates the port status, as shown in the following table.

Table 4 10/100/1000Base-T auto-sensing Ethernet port LEDs

description

LED Status Meaning

10/10

0/100

0Base-

auto-se

nsing

Ethern

et port

LED

Rate

mode

Solid

green

The port operates at the rate of

1000 Mbps; the LED is fast

blinking when data is being sent

and/or received on the port.

Solid

yellow

The port operates at the rate of

10/100 Mbps; the LED is fast

blinking when data is being sent

and/or received on the port.

Blinking

yellow (3

Hz)

POST failed on the port.

Off The port has not gone up.

Duple

mode

Solid

green

The port operates in full-duplex

mode; the LED is fast blinking

when data is being sent and/or

received on the port.

Solid

yellow

The port operates in half-duplex

mode; the LED is fast blinking

when data is being sent and/or

received on the port.

Blinking

yellow (3

Hz)

POST failed on the port.

Off The port has not gone up.

NOTE:

By default, the port LED is in the rate mode. To change the rate mode

to duplex mode, you can press the mode button. For more

information about the mode button, see the installation manuals of

different switch series.

Installing and Removing an Optional

Interface Card

NOTE:

• This section takes the LSW1SP4P0 interface card and the H3C

S5820X-28C switch to illustrate the module installation and

removal.

• The installation tools are not shipped together with H3C’s

Ethernet switches. You need to prepare the tools.

The following tools are needed for installation and removal:

• Phillips screwdriver

• ESD-preventive wrist strap

Installing an Interface Card

1. Put on an ESD-preventive wrist strap and make sure that the strap

is in good contact with your skin and is properly grounded.

2. Loosen the mounting screws of the blank panel on the expansion

slot of the switch's front panel with a Phillips screwdriver and

remove the blank panel, as shown in Figure 5.

Figure 5 Remove a blank panel

(1) Phillips screwdriver (2) Switch's front panel

(3) Blank panel

NOTE:

Keep the removed blank panel properly for future use.

3. Unpack the interface card.

Figure 6 Interface card appearance

(1) Captive screw (2) Ejector lever

4. Gently push the interface card in along the guide rails until the

interface card is in close contact with the switch (see callout 1

in Figure 7). Then

push the ejector levers at both sides inward (see

callout 2 in Figure 7).

5. Fasten the captive screws with a Philips screwdriver to fix the

interface card.

Figure 7 Install an interface card

Removing an Interface Card

1. Put on an ESD-preventive wrist strap and make sure that the strap

is in good contact with your skin and is properly grounded.

2. Loosen the captive screws at both sides of the interface card using

a Phillips screwdriver.

3. Hold the ejector levers at both sides of the interface card and push

them outward (see callout 1 in Figure 8). Pul

l the interface card

along the guides until it completely comes out of the switch chassis

(see callout 2 in Figure 8).

Figure 8 Remove an interface card

NOTE:

hen installing or removing an optional interface card, pay

attention to the following points:

• Avoid touching the surface-mounted components directly with

your hands.

• Avoid using excessive force in the operation.

• After removing an interface card, if no module is to be installed,

install the blank panel as soon as possible to prevent dust and

ensure the normal ventilation in the switch.

Page is loading ...

H3C LSW1SP2P0 User manual

Brand: H3C

Model: LSW1SP2P0

Category: Network switches

Type: User manual

This manual is also suitable for

Download PDF

report

H3C LSW1SP2P0 User manual

This manual is also suitable for

H3C LSW1SP2P0 User manual

Related papers

Other documents