XPOtool 61138 The XPOtool 61138 is a 500W sheet nibbler designed for precise cutting of mild steel (up to 1.6mm), stainless steel (up to 1.2mm), and aluminum (up to 2.5mm). It features a no-load speed of 2000 (±10%) RPM and is equipped with a variety of accessories, including 2 carbon brushes, an operation manual, a service book, an open wrench, and a socket hey wrench (2.5). With its ergonomic design and safety features, the XPOtool 61138 is an ideal tool for metalworkers and DIY enthusiasts alike.
XPOtool 61138 The XPOtool 61138 is a 500W sheet nibbler designed for precise cutting of mild steel (up to 1.6mm), stainless steel (up to 1.2mm), and aluminum (up to 2.5mm). It features a no-load speed of 2000 (±10%) RPM and is equipped with a variety of accessories, including 2 carbon brushes, an operation manual, a service book, an open wrench, and a socket hey wrench (2.5). With its ergonomic design and safety features, the XPOtool 61138 is an ideal tool for metalworkers and DIY enthusiasts alike.
Operation Manual
Sheet Nibbler
61138
service@wiltec.info
Introduction
To minimise the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Technical specifications
Model
Rated voltage
Rated frequency㎐
Input power
No load speed
Max. cutting thickness㎜
Mild steel
Stainless steel
Aluminium
Accessories
•
•
General safety rules (for all tools)
Warning:
Work area safety
• Keep your work area clean and well lit.
• Do not operate power tools in explosive atmospheres, e.g., near flammable liquids,
gases, or dust.
• Keep bystanders, children, and visitors away while operating the tool.
Electrical safety
• Power tool plugs must match the outlet. Never modify the plugs in any way. Do not use
any adapter plugs with earthed power tools. Unmodified plugs and matching outlets will
reduce the risk of electric shocks.
• Avoid body contact with grounded surfaces such as pipes, radiators, cookers, and re-
frigerators.
• Do not expose power tools to rain or moisture.
• Do not abuse the cable. Never use the cable to carry a tool or pull the plug from the
socket.
• When operating a power tool outside, use an outdoor extension cord.
Personal safety
• Stay alert, concentrate on what you are doing and use common sense when operating a
power tool.
• Dress properly. Do not wear loose clothing or jewellery. Tie long hair together.
• Avoid accidental starting. Be sure that the switch is turned off before plugging in the
device.
• Remove adjusting keys or wrenches before turning the tool on.
• Do not overreach. Always keep proper footing and balance.
• Use safety equipment. Always wear eye protection. Dust mask, non-slip safety shoes, a
hard hat and hearing protection must be used for appropriate conditions.
no
Tool use and care
• Use clamps or other ways to secure and support the workpiece to a stable platform.
• Do not force the tool. Use the correct tool for your application.
• Do not use the tool if the switch does not work properly.
• Disconnect the plug from the power source before making any adjustments, changing
equipment, or storing the tool.
• Store idle tools out of reach of children and other untrained people.
• Maintain tools with care. Keep cutting tools sharp and clean.
• Check for misalignment or smoothly operating moving parts, broken parts and any other
condition that may affect the operation.
• Only use equipment that is recommended by the manufacturer for your model.
Service
• only
•
Specific safety rules
• Do not
• Always be sure that the tool is switched off and unplugged before carrying out any work
on the tool.
• Always lead the power supply cord away from the tool towards the rear.
• Do not touch the blade or the workpiece immediately after operation; it might be ex-
tremely hot and could burn your skin.
• Hold the tool by the insulated gripping surfaces when performing an operation where the
cutting tool may get in contact with a hidden wiring or its own cable.
•
• Apply the machine to the workpiece only when switched on.
• Always switch the machine off and wait until it has come to a standstill before placing it
down.
• Never allow children to use the machine.
• Some material contains chemicals which might be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material supplier safety data.
Warning: Save these instructions warning: misuse or failure to follow the safety rules stated in
this instruction manual may cause serious personal injury.
Symbols
Voltage in Volt
No load speed
Amperage in Ampere
Revolutions per minute
Frequency in Hertz
Protection class II
Functional description
Assembly
•
Caution:
•
•
№
Name
№
Name
1
3b
2
4
3a
5
№
Name
№
Name
1a
3
1b
4
2
5
№
Name
№
Name
№
Name
№
Name
1
2
1
3
2
4
Changing the position (Fig. 5)
Warning:
•
•
•
•
Switch on and off (Fig. 6)
Caution:
Thickness gauge (Fig. 7)
№
Name
№
Name
1
3
2
4
(1)
№
Name
№
Name
1
3
2
Thickness of die cut
Line of cut (Fig. 7)
•
•
•
Cutting corrugated or trapezoidal metal sheets
Maintenance and daily care
Caution:
•
•
•
(1)
(2)
(3)
Replacing carbon brushes
•
•
•
Caution:
•
•
№
Name
№
Name
1
2
Parts list and exploded view
№
Name
Unit
Qty
№
Name
Unit
Qty
1
31
2
32
3
33
4
34
5
35
6
36
7
37
8
38
9
39
10
40
11
41
12
42
13
43
14
44
15
45
16
46
17
47
18
48
19
49
20
50
21
51
22
52
23
53
24
54
25
55
26
56
27
57
28
58
29
59
30
60
Disposal regulations
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
XPOtool 61138 The XPOtool 61138 is a 500W sheet nibbler designed for precise cutting of mild steel (up to 1.6mm), stainless steel (up to 1.2mm), and aluminum (up to 2.5mm). It features a no-load speed of 2000 (±10%) RPM and is equipped with a variety of accessories, including 2 carbon brushes, an operation manual, a service book, an open wrench, and a socket hey wrench (2.5). With its ergonomic design and safety features, the XPOtool 61138 is an ideal tool for metalworkers and DIY enthusiasts alike.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI