2. PRODEMAND
  3. 2015 Ford Focus SE

PRODEMAND 2015 Ford Focus SE User manual

  • Hello! I'm here to assist you with the user manual for the Transmission Control Module (TCM). This document provides detailed steps for the removal and installation process, including the tools, materials and procedures needed. I've reviewed the contents, so feel free to ask questions about any particular part of the manual or the TCM itself. I can also help you find specific information from the document.
  • Is TCM Programming necessary if the TCM is being reused?
    What fluid is used to lubricate the O-rings?
    What should be inspected on the TCM mating surface?
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
1/13
REMOVAL AND INSTALLATION > TRANSMISSION CONTROL MODULE (TCM)
NOTE: For information on Ford Color Coded Illustrations refer
to COLOR-CODING - FORD .
Special Tool(s) / General Equipment
Ford Diagnostic Equipment
Materials
Name Specification
Motorcraft ® Dual Clutch Transmission Fluid XT-
11-QDC
WSS-M2C200-D2
REMOVAL AND INSTALLATION > TRANSMISSION CONTROL MODULE (TCM) >
REMOVAL
1.
Position the vehicle on a hoist. Refer to: Jacking and Lifting - Overview .
2.
NOTE: TCM Programming is NOT necessary if the TCM
is being re-used.
Download the module information to the diagnostic tool using the Programmable Modules
Installation routine.
3.
Remove the air deflector.
YMMS: Jul 10, 2021
Engine:
2.0L Eng
License:
VIN: Odometer:
2015 Ford Focus SE
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
2/13
Courtesy of FORD MOTOR COMPANY
4.
Remove the underbody shield.
Courtesy of FORD MOTOR COMPANY
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
3/13
5.
Push up on the front of the wiring routing bracket to release the retainer and position it aside.
Courtesy of FORD MOTOR COMPANY
6.
NOTE: Make sure that the terminals or pins/sockets of
the transmission control module (TCM) and the TCM
electrical connector are not bent or damaged.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
4/13
Disconnect the wiring, remove the wiring retainers from the wiring harness and position aside the
wiring harness. Remove the TCM bolts.
Courtesy of FORD MOTOR COMPANY
7.
Remove the TCM.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
5/13
Courtesy of FORD MOTOR COMPANY
8.
Remove and discard the O-ring seals.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
6/13
Courtesy of FORD MOTOR COMPANY
9.
NOTE: Make sure that the mating faces are clean and
free of corrosion and foreign material.
Inspect the TCM mating surface for corrosion and debris.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
7/13
Courtesy of FORD MOTOR COMPANY
REMOVAL AND INSTALLATION > TRANSMISSION CONTROL MODULE (TCM) >
INSTALLATION
1.
NOTE: Make sure that the mating faces are clean and
free of corrosion and foreign material.
NOTE: Install new O-rings.
Install new O-rings and lubricate with transmission fluid.
Material: Motorcraft ® Dual Clutch Transmission Fluid / XT-11-QDC (WSS-M2C200-D2)
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
8/13
Courtesy of FORD MOTOR COMPANY
2.
NOTE: Do not force the TCM onto the transmission or
damage may occur.
NOTE: Make sure the TCM sits flush on the
transmission or damage can occur.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
9/13
Install the TCM on the transmission. Apply light pressure to seat the O-rings. If the TCM does not
push in place with light pressure, remove the TCM and slightly turn the TCM gears and retry
installing the TCM on the transmission.
Courtesy of FORD MOTOR COMPANY
3.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
10/13
NOTE: Make sure that the terminals or pins/sockets of
the transmission control module (TCM) and the TCM
electrical connector are not bent or damaged.
Install the bolts and the wiring.
Torque: 20 lb.ft (27 Nm)
Courtesy of FORD MOTOR COMPANY
4.
Install the wiring routing bracket.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
11/13
Courtesy of FORD MOTOR COMPANY
5.
Install the underbody shield.
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
12/13
Courtesy of FORD MOTOR COMPANY
6.
Install the air deflector.
Courtesy of FORD MOTOR COMPANY
7/10/2021
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
13/13
7.
NOTE: New units must be configured using the
Programmable Modules Installation Routine in the diagnostic
tool.
Upload the module information from the diagnostic tool to the module using the Programmable
Modules Installation routine. Use the General Equipment: Ford Diagnostic Equipment
8.
Using the diagnostic tool, perform the TR Sensor Adaptive Learn and Clutch Adaptive Learn
routines found in the TCM Adaptive Learning sub-menu.
/