PRODEMAND 2006 User manual

Brand
PRODEMAND
Model
2006
Type
User manual

PRODEMAND 2006 is an advanced diagnostic tool that empowers you to effortlessly diagnose and repair complex automotive issues. With its comprehensive capabilities, you can seamlessly access real-time data, retrieve trouble codes, and perform in-depth system analysis. This versatile device is your trusted companion for pinpointing faults, resetting modules, and reprogramming ECUs. Get ready to elevate your automotive expertise and tackle any challenge with confidence using PRODEMAND 2006.

PRODEMAND 2006 is an advanced diagnostic tool that empowers you to effortlessly diagnose and repair complex automotive issues. With its comprehensive capabilities, you can seamlessly access real-time data, retrieve trouble codes, and perform in-depth system analysis. This versatile device is your trusted companion for pinpointing faults, resetting modules, and reprogramming ECUs. Get ready to elevate your automotive expertise and tackle any challenge with confidence using PRODEMAND 2006.

4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
1/9
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY > REMOVAL
AND INSTALLATION
Tip: Fuel Pump Removal
Fig 1: Removing/Installing Fuel Level Sensor Unit, Fuel Filter And Fuel Pump Assembly
Courtesy of NISSAN MOTOR CO., U.S.A.
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY > REMOVAL
AND INSTALLATION > REMOVAL
WARNING: Read "General Precautions" before working on
the fuel system. Refer to "GENERAL PRECAUTIONSī¢".
1. Check fuel level on fuel gauge. If fuel gauge indicates more than the level as shown in the figure (full
or almost full), drain fuel from fuel tank until fuel gauge indicates level as shown in the figure or
below.
YMMS: Apr 6, 2022
Engine:
3.5L Eng
License:
VIN: Odometer:
2006 Nissan Murano SE
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
2/9
NOTE: Because fuel will be spilled when removing fuel
level sensor unit for the top of fuel is above the fuel level
sensor unit installation surface.
1. As a guide, fuel level becomes the position as shown in the figure or below when approximately
20 --> (5-1/4 US gal, 4-3/8 Imp gal) of fuel are drained from fuel tank.
2. In a case that fuel pump does not operate, perform the following procedure.
Fig 1: Checking Fuel Level On Fuel Gauge
Courtesy of NISSAN MOTOR CO., U.S.A.
a. Insert hose of less than 25 mm (0.98 in) in diameter into fuel filler tube through fuel filler opening
to draw fuel from fuel filler tube.
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
3/9
b. Disconnect fuel filler hose from fuel filler tube. Refer to "FUEL TANK ".
c. Insert hose into fuel tank through fuel filler hose to draw fuel from fuel tank.
2. Release the fuel pressure from the fuel lines. Refer to "FUEL PRESSURE RELEASE ".
3. Open fuel filler lid.
4. Open fuel filler cap and release the pressure inside fuel tank.
5. Remove rear seat cushion trim and pad bolts, then lift up rear seat cushion. Refer to "REAR SEAT ".
6. Remove inspection hole cover for main and sub fuel level sensor unit by turning clips
counterclockwise by 90 degrees and by mating both cover hole and clip shape.
Fig 2: Turning Clips
Courtesy of NISSAN MOTOR CO., U.S.A.
7. Disconnect harness connector and quick connectors for EVAP hose and fuel feed tube
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
4/9
Fig 3: Disconnecting Quick Connectors EVAP Hose
Courtesy of NISSAN MOTOR CO., U.S.A.
Disconnect quick connector as follows:
1. Hold the sides of quick connector, push in tabs and pull out fuel feed tube.
2. If quick connector sticks to tube of fuel level sensor unit, push and pull quick connector several
times until it start to move. Then disconnect quick connector by pulling.
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
5/9
Fig 4: Disconnecting Quick Connect Fitting
Courtesy of NISSAN MOTOR CO., U.S.A.
CAUTION:
1. Quick connector can be disconnected when the tabs are
completely depressed. Do not twist it more than
necessary.
2. Do not use any tools to disconnected quick connector.
3. Keep resin tube away from heat. Be especially careful
when welding near the resin tube.
4. Prevent acid liquid such as battery electrolyte, etc. from
getting on resin tube.
5. Do not bend or twist resin tube during installation and
disconnection.
6. Do not remove the remaining retainer on hard tube (or
the equivalent) except when resin tube or retainer is
replaced.
7. When resin tube or hard tube (or the equivalent) is
replaced, also replace retainer with new one.
8. Replace same color retainer as before replacing.
Retainer color: Green
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
6/9
Fig 5: Identifying Quick Connector
Courtesy of NISSAN MOTOR CO., U.S.A.
9. To keep the connecting portion clean and to avoid
damage and foreign materials, cover them completely
with plastic bags or something similar.
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
7/9
Fig 6: Covering Fuel Line With Plastic Bags
Courtesy of NISSAN MOTOR CO., U.S.A.
8. Remove retainer for main and sub fuel level sensor unit with fuel tank lock ring wrench [SST] by
turning counterclockwise.
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
8/9
Fig 7: Identifying Fuel Tank Lock Ring Wrench
Courtesy of NISSAN MOTOR CO., U.S.A.
9. Remove main fuel level sensor unit, fuel filter and fuel pump assembly, and sub fuel level sensor unit.
1. Raise main fuel level sensor unit, fuel filter and fuel pump assembly, and disconnect fuel hose
connector (push in tabs and pull out) and sub fuel level sensor unit harness connector.
2. Raise and release sub fuel level sensor unit to remove.
4/6/22, 6:44 PM
Printer Friendly View
https://www1.prodemand.com/Print/Index?content=tabs&module=true&tab=true&terms=true&ymms=false&selectorMode=&className=
9/9
Fig 8: Removing Main Fuel Level Sensor Unit
Courtesy of NISSAN MOTOR CO., U.S.A.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

PRODEMAND 2006 User manual

Brand
PRODEMAND
Model
2006
Type
User manual

PRODEMAND 2006 is an advanced diagnostic tool that empowers you to effortlessly diagnose and repair complex automotive issues. With its comprehensive capabilities, you can seamlessly access real-time data, retrieve trouble codes, and perform in-depth system analysis. This versatile device is your trusted companion for pinpointing faults, resetting modules, and reprogramming ECUs. Get ready to elevate your automotive expertise and tackle any challenge with confidence using PRODEMAND 2006.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents