EAGLE PEAK HPG-1010 User manual

Brand: EAGLE PEAK

Model: HPG-1010

Type: User manual

This manual is also suitable for

10 ft. x 10 ft. Steel Outdoor Pergola

10'x10' Pergola

WARNING:

Fabric meets CPAI-84 specification for flame resistance. It is Not

Fire Proof. The fabric will burn if left in continuous contact with

any flame source. The application of any harsh chemicals to the

fabric may render the flame-resistant properties ineffective.

Always read and follow the instructions before use. When assembling

and using this product, basic safety precautions must always be fol

lowed to reduce risk of personal injury and damage to the product or

surroundings.

Be sure to keep all children and pets away from assembly area. Some

parts contain sharp edges. Wear protective gloves when handling these

items. It is recommended that, for safety issues, at least 2 people as

semble the pergola. It may take to 90 minutes to assemble this pergola.

It is important to schedule enough time to complete the assembly. You

should not leave the unit unattended if it is not fully assembled, even if

it is already anchored to the ground. You should begin the assembly no

less than 6 feet from any permanent structures such as fences,a garage,

a house, overhanging branches, electrical wires or laundry lines. You

must assemble your unit on level ground or a platform.

The unit must be anchored to the ground with proper anchors. Failure

to do so may risk it blowing away.

Check that all screws are tight before and during usage. Do not place

any type of heat conductor or source under, or within 5 feet of the unit

including, but not limited to, a barbeque or space heater.

The pergola is designed to provide shade only. Do not use this pergola

in strong wind and rain. Wind and rain can damage the pergola and

could result in injury to you and others. It is recommended that the Canopy

be removed during strong winds and stormy conditions.

Check all available parts. Before assembling the pergola, check to make

sure you have all the parts listed in the Parts List.

PARTS LIST

Description

Post

Cross Beam

Roof Tube

Pulling Rod

Guide Tube

Bracket

Corner Support

Bracket

Post Decoration

Base Plate Cover

Post Hoof

Shade Fabric

Sketch QTY.

Bolt

Anchor

Allen Key

Roof Tube

4 pcs

2 pcs

6 pcs

2 pcs

4 pcs

8 pcs

4 pcs

2 pcs

84 pcs

8 pcs

2 pcs

12 pcs

8 pcs

6 pcs

M6x12mm

M6x35mm

M6x55mm

M6x75mm

Assembly

STEP 1

Fig. 1 Fig. 2

Fig. 1

Fig. 2

Fig.1: Let Post Decoration (R) pass through Post (A1) first. Then use Bolt (M6x12) (AA) to

connect Post (A1) and Post Hoof (S).

Fig.2: Let Post Decoration (O) pass through Post (A1) first. Please make sure to complete

this steps before next following steps. Then use Bolt (M6x75) (DD) and Bracket (N) to assemble

Cross Beam (C2) and Cross Beam (B1) to Post (A1).

Use Bolt (M6x35) (BB) to connect Post Decoration (Q) and Cross Beam (C2).

Repeat these instructions for the other posts.

Assembly

STEP 2

Fig. 3 Fig. 4

Fig. 3

NDD

Fig. 4

Fig.3: Let Post Decoration (R) pass through Post (A1) first. Then use Bolt (M6x12) (AA) to

connect Post (A1) and Post Hoof (S).

Fig.4: Let Post Decoration (O) pass through Post (A1) first. Please make sure to complete

this steps before next following steps. Then use Bolt (M6x75) (DD) and Bracket (N) to assemble

Cross Beam (C1) and Cross Beam (B2) to Post (A1). Use Bolt(M6x35) (BB) to connect Post

Decoration (Q) and Cross Beam (C1).

Repeat these instructions for the other posts.

Assembly

STEP 3

A1 H1 H2

Fig. 5

B1 / C1

B2 / C2

Fig. 6 Fig. 7

Fig. 6

Fig. 7

A1 H1

H1 / H2

B1 / B2 / C1 / C2

Fig. 8

FF S

Fig.5: Use Bolt (M6x12) (AA) to connect Cross Beam (B1)

and Cross Beam (B2).

Use Bolt(M6x12) (AA) to connect Cross Beam (C1) and

Cross Beam C2.

Fig.6: Use Bolt(M6x12) (AA) to connect Connector (H2/H1)

and Post (A1).

Fig.7: Use Bolt(M6x12) (AA) to connect Connector (H2/H1)

and Cross Beam (B1/B2/C1/C2).

Fig.8: Hammer Anchors (FF) through one of the holes at

each post base, into the ground to stablize the .

Repeat these instructions for the other posts.

Assembly

STEP 4

Fig. 9 Fig. 10

Fig. 9

B1 / B2

D1 / D2

Fig. 12

Fig. 11

Fig. 10

Fig. 12

Fig.9: Use Bolt(M6x12) (AA) to connect Roof Tube (D1) and

Roof Tube (D2).

Fig.10: Use Bolt (M6x55) (CC) to assemble Roof Tube (D1/D2)

and Cross Beam (B1/B2).

Repeat these instructions for the other roof tubes.

Fig.11: At the bottom of Post (A1), using Bolt (AA) to connect

Bracket (G) and Post (A1). Insert Guide Tube (F) through to

Bracket (M) , then to Bracket (G).

Fig.12: At the top of Post (A1), insert Guide Tube (F) to Bracket

(G), then using Bolt (AA) to connect Bracket (G) and Post (A1).

Repeat these instructions for the other roof tubes.

Fig. 11

Assembly

STEP 5

Fig. 13 Fig. 14

CLICK!

Fig. 13

Fig. 14

E1 & E2

Fig. 13

Fig.13: Insert the Pulling Rod (E1) to Pulling Rod (E2).

Fig.14: Pass the 2pcs Shade Fabric (P) through the Roof Tube (D1/D2) in turn as above diagram.

Insert the Pulling Rod (E1/E2) to Shade Fabric. After assembled, please pull the Shade Fabric,

make sure it runs smoothly.

Fig.15: Using Bolt (AA) to connect Bracket(M) to Pulling Rod(E1/E2).

Fig. 15

Any questions on assembly or parts, please contact: [email protected]

Made in china

EAGLE PEAK HPG-1010 User manual

Brand: EAGLE PEAK

Model: HPG-1010

Type: User manual

This manual is also suitable for

10 ft. x 10 ft. Steel Outdoor Pergola

Download PDF

report

EAGLE PEAK HPG-1010 User manual

This manual is also suitable for

EAGLE PEAK HPG-1010 User manual

Other documents