1
RDC-7.1
• For full details on using the RDC-7.1, refer to the main instruction manual.
• For optimum surround playback, set the distance between the listener and the speakers so that the time it takes
the sound to reach the listener is the same. Also, you need to set each speaker volume level individually in order
to balance the volume level between speakers (See pages 92 to 94 in the main manual).
Enjoying Home Theater
Center speaker
Complements the sound effects from
front left and right speakers to enrich
and clear the sound image and
movement. In movies, an actor’s speech
comes mainly from the center speaker.
• When placing the center speaker
above or below the TV, tilt it toward
the listener’s ears.
• Place the center speaker as close to
the screen or monitor as possible and
in the center between the left and
right front speakers. When placing
the center speaker near the TV, use a
shielded speaker.
Subwoofer
Outputs only bass sounds to
enhance and complement bass
sound effects.
Front left and right speakers
Outputs overall sound. They play the most important role in a home theater
system, by creating basic sound images and fields.
• Place the front left and right speakers symmetrically and so that the dis-
tance from the listening position is the same.
• When placing speakers, direct the speakers toward the position of the
listener’s ears where the listener sits to enjoy music or movies.
Surround left and right speakers
Enhances the sensation of being at a live performance by giving three-dimensional
sound movement to the sound effects.
• Place these speakers on each side of, or angled behind, the listener.
• Place the surround speakers symmetrically from the listener position and so that the
distance from the listener is equal between left and right surround speakers.
Surround back speakers
Enhances the sound space
representation with
surround channel signals.
Recreating sound movement
effects and sound fields
behind the listener gives a
more realistic experience.
Quick Guide
2
You can connect the RDC-7.1 (PRE OUT A terminals) and the power amplifier through RCA terminals using RCA type
audio pin cables. Also you can connect the amplifiers through XLR (Balanced) type terminals using XLR type cables.
The figure below illustrates the connection to the RDA-7.1, a power amplifier of the same product series. For connecting
speakers, refer to the instruction manual that comes with your amplifier.
Connecting through RCA type PRE OUT A terminals
Connecting through XLR (Balanced) type PRE OUT A terminals
Connecting a Power Amplifier
L
R
L
R
FRONT
CENTER
SURR
SURR
BACK
SUB
WOOFER
SURR BACK R
SURR R F
R
SUBWOOFER
PRE
OUT A
(
ASSIGNABLE
)
(
SINGLE
)
(
ASSIGNABLE
)
22
OUT
DIGITAL IN
(
BALANCED
)
AES/ EBU
DIGITAL IN
(
BALANCED
)
AES/ EBU
3
R
SPEAKER IMPEDANCE
4 OHMS MIN. PER EACH
SPEAKER TERMINAL
AC INLET
SEVEN CHANNEL AMPLIFIER
MODEL NO. RDA-7.1
INPUT
SELECT
FUSE
SURROUND BACK
RIGHT
SURROUND
RIGHT
12V TRIGGER
IN OUT
SURROUND
LEFT
CENTER
FRONT
LEFT
SURROUND BACK
LEFT
FRONT
RIGHT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
LINE INPUT
LINE INPUT
RDC-7.1
Power amplifier RDA-7.1
Audio connection cable
Subwoofer
L
R
L
R
FRONT
CENTER
SURR
SURR
BACK
SUB
WOOFER
SURR BACK R
SURR R FRONT R CENTER FRONT L
SURR BACK L
SURR L
SUBWOOFER
PRE
OUT A
(
ASSIGNABLE
)
(
SINGLE
)
(
SINGLE
)
(
ASSIGNABLE
)
(
ASSIGNABLE
)
ETHERNET
(
Net
-
Tune
)
AUDIO
The
i.LINK
logo
is
a
trademarks
of
Sony
Corporation, registered
in
the
U.S.
and
other
countries.
S400
22
11
66
55
OUT
1
3
2
3
9
8
4
5
OUT
LR R L
6
5
P
B
P
R
2
1
4
3
S VIDEOS VIDEO VIDEOVIDEO
OUT OUT
Y
P
B
P
R
OUT
L
R
FRON
T
DIGITAL IN
(
BALANCED
)
AES/ EBU
DIGITAL IN
(
BALANCED
)
AES/ EBU
SPEAKER IMPEDANCE
4 OHMS MIN. PER EACH
SPEAKER TERMINAL
AC INLET
SEVEN CHANNEL AMPLIFIER
MODEL NO. RDA-7.1
INPUT
SELECT
FUSE
SURROUND BACK
RIGHT
SURROUND
RIGHT
12V TRIGGER
IN OUT
SURROUND
LEFT
CENTER
FRONT
LEFT
SURROUND BACK
LEFT
FRONT
RIGHT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
LINE INPUT
LINE INPUT
Subwoofer
Power amplifier RDA-7.1
GND
(+)
(–)
Push
Push
RDC-7.1
3
An appropriate option board [H] [I] should be installed to connect a TV or a projector.
• This section describes the connections for displaying the video source or the operating information of the RDC-7.1
on a monitor device such as a TV or projector. Before making a connection, check the terminal types on the monitor
device and acquire the necessary cables by referring to page 31 in the main manual.
• When your TV or monitor has various types of input terminals, use the connection with which you can get the best
video quality. On TV screen or projector which is connected via COMPONENT terminal, you can view the images
from devices connected via VIDEO, S-VIDEO or COMPONENT terminal, because the RDC-7.1 has a built-in
video-up converter. However, you cannot view the images from devices connected via COMPONENT terminal on
TV or projector which is connected via VIDEO or S-VIDEO terminal (In this case of connection, images will be
available if you use an HDMI terminal board).
Connecting Monitors such as TV or Projector
K
L
S
BL
SL
C
S
BL
SL
C
MULTI
-
CH
IN
1
MULTI
-
CH
IN
2
AUDIO IN
1
3
2
1
PH
2
3
9
8
7
6
5
4
4
5
LRRL
GND
OUT
LR
LR
R L
F
G
L
IN
1
IN
2
OUT
HDMI
S
VIDEO VIDEO
IN IN
IN
1
IN
2
3
2
1
Y
PB
PR
COMPONENT
VIDEO
IN
3
IH
6
5
4
Y
P
B
PR
2
1
4
3
S VIDEOS VIDEO VIDEOVIDEO
OUT OUT
OUT
1
J
OUT
(
HD/ BNC
)
Y
P
B
P
R
Y
P
B
P
R
COMPONENT VIDEO
IN
(
HD/ BNC
)
K
ANTENNA
FM
75
AM
AC INLET
UDD
RS
232
IR
IN
+
12
V DC PWR SUPPLY
MAIN
GND
ZONE
3
ZONE
2
GND
C
D
E
B
A
12
V
TRIGGER
OUT
100mA MAX.
100mA MAX.
100mA MAX.
TOTAL
100mA MAX.
200mA MAX.
20mA MAX.
12 V
TRIGGER
OUT
E
VIDEO
IN
S VIDEO
IN
Y
P
B
PR
COMPONENT
VIDEO (RCA)
IN
Monitor device
such as TV or
projector for
Main room A
Video connection
cable
Component video
cable
S video
connection
cable
Option
4
An appropriate option board [H] [I] should be installed to connect a DVD player.
The description here guides you to make connection between the RDC-7.1 and your DVD player in a quickest way
where no modification is required for the default settings of the unit. The guidance is divided into 4 ways depending on
the type of DVD player: If you have an IntegraRESEARCH RDV-1.1, follow the steps in this page for the typical
connection procedure. If you plan to connect your DVD player, including the RDV-1.1, via the i.LINK terminal, refer
to page 5. If you have a universal DVD player without i.LINK terminals to connect, refer to page 6. Finally, if you have
any other DVD player than shown above, go to page 33 in the main manual.
Connecting to an IntegraRESEARCH DVD player RDV-1.1
1. Use an optical cable to connect the RDC-7.1’s DIGITAL IN OPTICAL 1 to the AUDIO OUT DIGITAL 1
OPTICAL on your RDV-1.1.
2. Use an AV cable to connect the RDC-7.1’s AUDIO IN 4 L/R to the AUDIO OUT D. MIX L/R on your
RDV-1.1.
3. Follow one of the instructions shown below to make a connection for video input.
1. Use a component video connection cable to connect the RDC-7.1’s COMPONENT VIDEO IN 1 to the VIDEO
OUT COMPONENT on your RDV-1.1. Note that TV or projector must also be connected via COMPONENT
terminal.
2. Use a S video cable to connect the RDC-7.1’s S VIDEO IN 1 to the VIDEO OUT S VIDEO on your RDV-1.1.
3. Use an AV cable to connect the RDC-7.1’s VIDEO IN 1 to the video output on your RDV-1.1.
4. Use an cable to connect the RDC-7.1’s terminal to the REMOTE CONTROL on your RDV-1.1.
Note:
If your AV Controller has i.LINK terminals, see page 5.
Connecting a DVD Player
COAXIAL OPTICAL OPTICALCOAXIAL
DIGITAL
1
DIGITAL
2
DIGITAL 2
(
BALANCED
)
AES/EBU
AUDIO
OUT
MODEL NO.
RDV
-
1.1
DVD
PLAYER
AC INLET
D. MIX FRONT SURR
1
CENTER SURR
2
L
R
L
R
IN
SUB
WOOFER
1
2
YPB PR
OUT
OUT
IN
REMOTE
CONTROL
VIDEO
OUT
COMPONENT
VIDEO
S
VIDEO VIDEO
S
VIDEO
Y
P
B
PR
Y
P
B
PR
IN
1
+
21
RS
232
HDMI
VIDEO
IN
IR
S400
(
AUDIO
)
AUDIO
OUT
HD VIDEO
OUT
COMPONENT
12
V
TRIGGER
SURR
MODE
(
AUDIO OUT
)
(
ASSIGNABLE
)
(
ASSIGNABLE
)
K
L
“Net
-
Tune”
is
a
trademark
of
Onkyo
Corporation.
ETHERNET
(
Net
-
Tune
)
22
11
66
55
44
33
22
1 1
C D
DIGITAL IN DIGITAL IN
OPTICAL COAXIAL
OUT
SBR SBL
SR SL
SUB C
FR FL
SBR SBL
SR SL
SUB C
FR
FL
E
MULTI
-
CH
IN
1
MULTI
-
CH
IN
2
AUDIO IN
1
3
2
1
PH
2
3
9
8
7
6
5
4
4
5
LRRL
GND
OUT
LR
LR
R L
F
G
L
IN
1
IN
2
OUT
HDMI
S
VIDEO VIDEO
IN IN
IN
1
IN
2
3
2
1
Y
PB
PR
COMPONENT
VIDEO
IN
3
IH
6
5
4
Y
P
B
PR
2
1
4
3
S VIDEOS VIDEO VIDEOVIDEO
OUT OUT
OUT
1
J
OUT
(
HD/ BNC
)
Y
P
B
P
R
Y
P
B
P
R
COMPONENT VIDEO
IN
(
HD/ BNC
)
K
ANTENNA
FM
75
AM
AC
INLET
(
SINGLE
)
A B
UDD
RS
232
IR
IN
+
12
V DC PWR SUPPLY
MAIN
GND
ZONE
3
ZONE
2
GND
C
D
E
B
A
12
V
TRIGGER
OUT
100mA MAX.
100mA MAX.
100mA MAX.
TOTAL
100mA MAX.
200mA MAX.
20mA MAX.
12 V
TRIGGER
OUT
E
A B
RDV-1.1
1. Optical
cable
4. cable
2. AV cable
3-1. Component video
connection cable
RDC-7.1
3-2. S video
cable
3-3. AV
cable
Option
5
Connecting to DVD player with i.LINK terminal
Disconnect the cable when this type of connection is made on an IntegraRESEARCH/Onkyo DVD player.
1. Use the S400 4-pin i.LINK cable to connect the i.LINK (AUDIO) terminal on the RDC-7.1 to the i.LINK
(AUDIO) terminal on the i.LINK (AUDIO)-enabled DVD player.
2. (Recommended) Use an audio connection cable to connect the RDC-7.1
’
s AUDIO IN 4 L/R to the analog
audio output on your DVD player.
3. Follow one of the instructions shown below to make a connection for video input.
(An appropriate option board [H] [I] should be installed to connect a DVD player.)
1. Use a component video connection cable to connect the RDC-7.1’s COMPONENT VIDEO IN 1 to the Compo-
nent Video Output on your DVD player. Note that TV or projector must also be connected via COMPONENT
terminal.
2. Use a S video connection cable to connect the RDC-7.1’s S VIDEO IN 1 to the S Video Output on your DVD
player.
3. Use a composite video connection cable to connect the RDC-7.1’s VIDEO IN 1 to the video output on your
DVD player.
4. When the connection is completed, power on the RDC-7.1 and TV (See steps 1 to 5 on page 7).
5. Assign the DVD input source.
(Remote controller)
1. Press the [Input] button, and then roll the scroll wheel to select “DVD.”
2. Press the scroll wheel, and then press the [Setup] button.
3. Use the [ ]/[ ] buttons to select “Input Setup,” and then press the [Enter] button.
4. Use the [ ]/[ ] buttons to select “Audio Assign” and then press the [Enter] button.
5. Use the [ ]/[ ] buttons to select “i.LINK,” and then use the [ ]/[ ] buttons to select the DVD player.
6. After setting, press the [Setup] button.
B
“Net
-
Tune”
is
a
trademark
of
Onkyo
Corporation.
ETHERNET
(
Net
-
Tune
)
B
(
ASSIGNABLE
)
(
ASSIGNABLE
)
K
L
22
11
66
55
44
33
22
11
C D
DIGITAL IN DIGITAL IN
OPTICAL COAXIAL
OUT
SBR SBL
SR SL
SUB C
FR FL
SBR SBL
SR SL
SUB C
FR
FL
E
MULTI
-
CH
IN
1
MULTI
-
CH
IN
2
AUDIO IN
1
3
2
1
PH
2
3
9
8
7
6
5
4
4
5
LRRL
GND
OUT
LR
LR
R L
F
G
L
IN
1
IN
2
OUT
HDMI
S
VIDEO VIDEO
IN IN
IN
1
IN
2
3
2
1
Y
P
B
PR
COMPONENT
VIDEO
IN
3
IH
6
5
4
Y
P
B
PR
2
1
4
3
S VIDEOS VIDEO VIDEOVIDEO
OUT OUT
OUT
1
J
OUT
(
HD/ BNC
)
Y
P
B
P
R
Y
P
B
P
R
COMPONENT VIDEO
IN
(
HD/ BNC
)
K
ANTENNA
FM
75
AM
AC
INLET
(
SINGLE
)
A
UDD
RS
232
IR
IN
+
12
V DC PWR SUPPLY
MAIN
GND
ZONE
3
ZONE
2
GND
C
D
E
B
A
12
V
TRIGGER
OUT
100mA MAX.
100mA MAX.
100mA MAX.
TOTAL
100mA MAX.
200mA MAX.
20mA MAX.
12 V
TRIGGER
OUT
E
A
Y
P
B
PR
COMPONENT
OUT (RCA)
R
L
VIDEO
OUT
ANALOG
S VIDEO
OUT
AUDIO OUT
3-2.
S video
connection
cable
2. Audio
connection
cable
1. i.LINK cable
RDC-7.1
DVD player
3-1.
Component
video
connection
cable
3-3.
Video
connection
cable
Option
6
Connecting to universal DVD player with Multichannel terminal (When an optional Multichannel
terminal board is installed on the RDC-7.1)
1. Make a connection for digital audio signal.
If your DVD player has optical output terminal:
Use an optical cable to connect the RDC-7.1’s DIGITAL IN OPTICAL 1 to the optical output on your DVD
player. Initially, the OPTICAL 1 digital input is assigned to the DVD input source.
If your DVD player has only coaxial output terminal:
Use a coaxial cable to connect the RDC-7.1’s DIGITAL IN COAXIAL 1-6 to the coaxial output on your DVD player.
And you’ll need to reassign the DVD input source after completion of the connection followed by power-on.
1. Press the [Input] button, and then roll the scroll wheel to select “DVD.”
2. Press the scroll wheel, and then press the [Setup] button.
3. Use the [ ]/[ ] buttons to select “Input Setup,” and then press the [Enter] button.
4. Use the [ ]/[ ] buttons to select “Audio Assign” and then press the [Enter] button.
5. Use the [ ]/[ ] buttons to select “Digital Audio,” and then use the [ ]/[ ] buttons to select appropriate ter-
minal (Coax 1-Coax 6).
6. After setting, press the [Setup] button.
2. Use three or four audio connection cables or a multichannel connection cable to connect the multichannel
output jack on your DVD player to the MULTI-CH IN 1 jack on the RDC-7.1.
3. If your DVD player has 2-channel analog audio output terminals, in addition to those for multichannel
output, use an audio connection cable to connect the RDC-7.1’s AUDIO IN 4 L/R to the terminals on your
DVD player.
4. Make a connection for video input (Refer to step 3 on page 5).
5. When the connection is completed, power on the RDC-7.1 and TV (See steps 1 to 5 on page 7).
6. Assign the DVD input source.
(Remote controller)
1. Press the [Input] button, and then roll the scroll wheel to select “DVD.”
2. Press the scroll wheel, and then press the [Setup] button.
3. Use the [ ]/[ ] buttons to select “Input Setup,” and then press the [Enter] button.
4. Use the [ ]/[ ] buttons to select “Audio Assign” and then press the [Enter] button.
5. Use the [ ]/[ ] buttons to select “Multichannel” and then use the [ ]/[ ] buttons to select “1.”
6. After setting, press the [Setup] button.
7. If you listen to an SACD or DVD-Audio disc, select “Multich” by pressing the [Audio SEL] button on the
remote controller.
K
L
“Net
-
Tune”
is
a
trademark
of
Onkyo
Corporation.
ETHERNET
(
Net
-
Tune
)
66
55
44
33
22
1 1
C D
DIGITAL IN DIGITAL IN
OPTICAL COAXIAL
SR SL
SUB C
FR FL
SBR SBL
SR SL
SUB C
FR
FL
E
MULTI
-
CH
IN
1
AUDIO IN
1
3
2
1
PH
9
8
7
6
5
4
LRRL
GND
LR
F
G
L
IN
1
IN
2
HDMI
S
VIDEO VIDEO
IN IN
IN
1
IN
2
3
2
1
Y
PB
PR
COMPONENT
VIDEO
IN
3
IH
6
5
4
Y
P
B
PR
OUT
1
J
OUT
(
HD/ BNC
)
Y
P
B
Y
P
B
P
R
COMPONENT VIDEO
IN
(
HD/ BNC
)
K
ANTENNA
FM
75
AM
A B
RS
232
IR
IN
+
12
V DC PWR SUPPLY
MAIN
GND
ZONE
3
ZONE
2
B
A
12
V
TRIGGER
OUT
200mA MAX.
20mA MAX.
12 V
TRIGGER
OUT
E
A B
Y
P
B
PR
COMPONENT
OUT (RCA)
R
L
R
L
VIDEO
OUT
FRONT SURR
SURR BACK
ANALOG
CENTER
SUB
WOOFER
S VIDEO
OUT
DIGITAL
AUDIO OUT
AUDIO OUTMULTICH OUT
OPTICAL
AUDIO OUTAUDIO OUT
VIDEO OUTVIDEO OUT
RDC-7.1
DVD player
1
22 22 2
3
444
Option
Option
7
1. Plug the supplied power cord into the AC
INLET.
2. Plug the other end of the power cord into the
wall outlet.
3. Press the [Standby/On] button to turn on the
RDC-7.1.
Press the [On] button when using the remote con-
troller.
4. Turn on your DVD player and TV.
5. Select the appropriate input on your TV.
Select the input to which the RDC-7.1 is
connected.
6. Select the DVD input source.
Press the [DVD] button on the RDC-7.1.
Roll the scroll wheel to select the DVD input
source, when using the remote controller. While
neither the [Mode] button nor [Input] button is
illuminated, rolling the scroll wheel changes the
input source and remote controller mode.
7. Start playback on your DVD player.
Make sure that your DVD player’s digital audio
output is turned on. On some players, the default
setting is off. With some DVD-Video discs, you
can select the audio format (Dolby Digital, DTS,
PCM) from a menu.
8. Adjust the volume.
Rotate the [Master Volume] dial on the RDC-7.1,
or press the [VOL] button on the remote controller,
to obtain volume as desired.
The volume can be adjusted from –
∞
, –81.5 dB to
+18.0 dB (Max). Since the RDC-7.1 has been
designed for home theater enjoyment, it has a wide
volume range, allowing precise adjustment.
Operating DVD Player with the RDC-7.1’s
Remote Controller
Remote Control Code must be registered before
operating a DVD player from other manufacturers. See
page 129 in the main manual.
When using an IntegraRESEARCH/Onkyo DVD player
with connection or i.LINK connection, operate the
player with the remote controller pointing at the
RDC-7.1.
1. Press the [Mode] button, then roll the scroll
wheel to select the DVD Mode.
2. The buttons encircled by gray lines on the left
figure are available for operation. See page 124
in the main manual for details.
AC
INLET
2
1
Power Cord
(supplied)
ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
Caps Delete
Language Loca
t
ion
Album Ar
tist GenrePlaylist
Repeat Video Music Photo
@.-'/
--
/
---
Direct Tuning
#
Custom
Display
Dimmer
T
V
Input
Sleep
Random
Main A Main B
Muting
AngleSubtitleAudio
MemorySearchA
-
BRepeat
On Standby
T
V
T
V CH
T
V VOL
E
x
i
t
G
u
i
d
e
Rec
Last Memory
Prev
CH
Enter
S
e
t
u
p
R
e
t
u
r
n
Test
Tone
CH SEL
Pure A
Surround
Direct
Stereo
Re
-
EQ
THX
A
ll
CH
ST
Level
+
Level
-
L Night
Audio
SEL
DSP DSP
+
10 0
Clear
123
456
789
Input
T
o
p
M
e
n
u
M
e
n
u
VOL
CH
Disc
I
+
-
+
-
Zone
3
Zone
2
InputMode
Macro
S
e
r
v
e
r
A
u
d
i
o
A
D
J
On
Standby/On
Standby
Pure Audio
On
Master Volume
Power
DVD Video 1 Video 2
Video 3 Video 4
Video 5 Video 6 Video 7
Tape 1
Tape 2
Tuner
Phono Net Audio
C D
Open/Close
Zone 2
()
GRN
Rec
/
Zone
3
()
RED
O f f
Phones
Clear
Rec
/
Zone 3Zone 2 Off DSPDisplay Tuning Tuning ModePreset Memory Setup ExitEnter
Dimmer
AV Controller RDC
-
7.1
3
88
8
6
6
3
To wall outlet
Connecting the Supplied Power Cord
Turning On the RDC-7.1 and playing
a DVD
SN 29343696
Printed in Japan
D0411-1
(C) Copyright 2004 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 3 4 3 6 9 6 *
Operating on the RDC-7.1:
Use the [ ] DSP [ ] buttons to select a listening
mode.
Operating with the remote controller:
Press the scroll wheel, and then press the listening mode
button you want to select.
Available buttons are indicated on the left figure. See
page 61 in the main manual for details.
Operating with the remote controller:
Press the scroll wheel, and then press the [Audio SEL]
button. See page 57 in the main manual for details.
See pages 50 through 51 in the main manual for basic operations with the remote controller.
See pages 68 through 71 in the main manual for details about Zone 2 operations.
See pages 66 through 67 in the main manual for multichannel playing.
On
Standby/On
Standby
Pure Audio
On
Master Volume
Power
DVD
Video
1 Video 2
Video 3 Video 4
Video 5 Video 6 Video 7
Tape 1
Tape 2
Tuner
Phono Net Audio
C D
Open/Close
Zone 2
()
GRN
Rec
/
Zone
3
()
RED
O f f
Phones
Clear
Rec
/
Zone 3Zone 2 Off DSPDisplay Tuning Tuning ModePreset Memory Setup ExitEnter
Dimmer
AV Controller RDC
-
7.1
PQRS TUV WXYZ
Caps Delete
Language Loca
t
ion
Album Ar
tist GenrePlaylist
Repeat Video Music Photo
--
/
---
Direct Tuning
#
Custom
Display
Dimmer
T
V
Input
Sleep
Random
Main A Main B
Muting
AngleSubtitleAudio
MemorySearchA
-
BRepeat
T
V VOL
E
x
i
t
G
u
i
d
e
Rec
Last Memory
Prev
CH
Enter
S
e
t
u
p
R
e
t
u
r
n
Test
Tone
CH SEL
Pure A
Surround
Direct
Stereo
Re
-
EQ
THX
A
ll
CH
ST
Level
+
Level
-
L Night
Audio
SEL
DSP DSP
+
10 0
Clear
789
T
o
p
M
e
n
u
M
e
n
u
VOL
CH
Disc
+
-
Zone
3
Zone
2
InputMode
Macro
S
e
r
v
e
r
A
u
d
i
o
A
D
J
DSP
Input source buttons
Scroll wheel
Audio SEL
Selecting Listening Modes
Changing the Audio Mode
(Remote control only)
Caps Delete
Language Loca
t
ion
Album Ar
tist GenrePlaylist
Repeat Video Music Photo
Display
Dimmer
T
V
Input
Sleep
Random
Main A Main B
Muting
AngleSubtitleAudio
MemorySearchA
-
BRepeat
E
x
i
t
G
u
i
d
e
Rec
Last Memory
Prev
CH
Enter
S
e
t
u
p
R
e
t
u
r
n
Test
Tone
CH SEL
Pure A
Surround
Direct
Stereo
Re
-
EQ
THX
A
ll
CH
ST
Level
+
Level
-
L Night
Audio
SEL
DSP DSP
T
o
p
M
e
n
u
M
e
n
u
VOL
CH
Disc
+
-
InputMode
S
e
r
v
e
r
A
u
d
i
o
A
D
J
Surround
THX
Stereo
All CH ST
Direct
Pure A
DSP
DSP
Other Information
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ONKYO RDV-1.1 User manual
-
Integra DTR-10.5 User manual
-
-
-
-
-
-
-
-