AMG AMG4781R-1550-C Instruction Sheet

  • Hello! I am an AI chatbot trained to assist you with the AMG AMG4781R-1550-C Instruction Sheet. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
AMG4781R-1550-C
Instruction Manual
Eight Channel Video Transmit Unit operating at 1550nm
wavelength with Integral WDM coupler
AMG Systems Ltd. reserves the right to make changes to this document without notice. The information
herein is believed to be accurate. No responsibility is assumed by AMG for its use.
Page 1 of 2 AMG4781R-1550-C
Instruction Sheet D16665-
00.doc
CH1
DATA OR
ETHERNET
CH2
CH3
CH4
CH5
CH6
CH7
CH8
PRIMARY
TX RX
SECONDARY
TX RX
AMG
OPT PRESENTO
MARY PRI
CONDAR
Y
SE
VID PRESE EO NT
POWER
BANK A
TX RX
BANK B
DATA/A O PR E UDI ES
TX RX NT
4781R-1550-C
CH1 CH2
CH3 CH4
CH5 CH6
CH7 CH8
The AMG4781R-1550-C is a standalone eight channel video transmit unit designed to transmit eight
video signals to an AMG4781-1550-C, or AMG4782R-1550-C, 8 channel receiver. It requires one
single mode optical fibre for the transmission of the video. It incorporates a 1550nm/1310nm
wavelength division multiplexer. This allows the user to combine a signal from a unit transmitting at
1310nm wavelength onto the same fibre. The 1310nm signal can be in the same or in a different
direction to the 1550nm signal.
The AMG4781R-1550-C is designed to plug into an AMG2000 or an AMG2005 subrack which in turn
fits into a 19” rack system.
Connections
Video Input Connections
Connector ...........................................75 ohm BNC Socket.
Input Impedance..................................75 ohm terminated.
Input Level...........................................1 volt p-p nominal
Frequency Response ..........................10Hz to 5.75MHz min.
No of channels.....................................8
4781R-1550-C
4700 optics (Pr ary)im
1550nm
TX RX
1310nm Input or Output
1310nm
1550nm
OPTO IN OPTO OUT
8 Video Inputs
Optical Connections
PRIMARY OPTO OUT
This carries the 1550nm signal from this unit
together with a 1310nm signal from or to an
additional 1310nm unit.
Connector............................................LC/PC
Primary Optical Launch Power............-6dBm
Wavelength..........................................1550nm
Optical Fibre........................................Single mode
PRIMARY OPTO IN
1310nm signal input or output
Connector............................................LC/PC Combined 1310nm
and 1550nm signal
Optical Fibre........................................Single mode
AMG Systems Ltd. reserves the right to make changes to this document without notice. The information
herein is believed to be accurate. No responsibility is assumed by AMG for its use.
Page 2 of 2 AMG4781R-1550-C
Instruction Sheet D16665-
00.doc
Power Connection
Power supply.......................................from plug in connection on the 2000 or 2005 subrack
Power consumption.............................8 Watts max.
Indicators
Power...................................................Green - unit powered
Off - no power applied to unit
Primary Opto Sync TX.........................Green - optical channel transmitting
Off - optical channel not transmitting
Primary Opto Sync RX ........................Not Used
Secondary Opto Sync TX....................Not Used
Secondary Opto Sync RX....................Not Used
Video Present .....................................Green - video signal present on video input BNC
Off - no video signal present on video input BNC
Data Present TX..................................Not Used
Data Present RX..................................Not Used
Physical Information
Dimensions
Height ..................................................3U Plug-in
Width....................................................14HP
Depth...................................................172mm excluding connectors
Weight..................................................1000 grams
Mounting Details
The unit is designed to be mounted within an AMG2005 Subrack on standard card guides. Note the
AMG2005 Subrack is supplied with guide rails every 14HP. In order to fit this unit in the subrack it may
be necessary to move some card guides by pulling gently on the card guides.
Safety
The 4700 series of products uses a Class 1 laser system in accordance with EN 60825-2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:
Do not stare with unprotected eyes or with any unapproved collimating device at fibre ends or
connector faces, or point them at other people.
Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with the optical fibres systems see EN
60825-2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within the AMG4700 products.
In case of problem or failure contact your local support centre or AMG Systems Ltd, Technical Support
Department on tel. +44 (0) 1767 600777.
See unit data sheet for full specification.
/