HDL HDL-MPS04-RF.18 User manual

Wireless 4 channels Dry Contact

HDL-MPS04-RF.18

www.hdlautomation.com

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual

Version

Date

Description

V1.0

2015.09.06

Create new document

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual

INDEX

1. Overview........................................................................................................................................1

1.1 General Information...........................................................................................................1

1.2 Functionalities Description............................................................................................... 1

1.3 Device Description.............................................................................................................1

2. Safety Instructions....................................................................................................................... 2

3. Technical Data.............................................................................................................................. 2

4. Installation..................................................................................................................................... 3

5. Software Configuration................................................................................................................4

5.1 Wireless Setting via Mesh Gateway...............................................................................4

5.2 Basic Information............................................................................................................... 5

5.2.1 Change the ID of the device.................................................................................6

5.2.2 Remark.....................................................................................................................6

5.3 Configuration...................................................................................................................... 6

5.3.1 Remark.....................................................................................................................6

5.3.2 Switch type.............................................................................................................. 6

5.3.3 Unqualifiedde.......................................................................................................... 9

5.3.4 Delay time................................................................................................................9

5.3.5 Dimming................................................................................................................. 10

5.3.6 Target......................................................................................................................10

5.3.7 Low Limit................................................................................................................11

5.3.8 Setting For Keys................................................................................................... 11

5.4 Security Setting................................................................................................................ 12

6. Online Upgrade.......................................................................................................................... 13

6.1 Automatic Upgrade.......................................................................................................... 13

6.2 Manual Upgrade.............................................................................................................. 14

7 FAQ................................................................................................................................................15

8. Note.............................................................................................................................................. 16

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 1

1. Overview

1.1 General Information

HDL-MPS04-RF.18 wireless dry contact module, it has 4 channels dry contact, can

control target by switch. The module should work in conjunction with wireless gateway.

1.2 Functionalities Description

4 channels dry contact inputs, 4 channels LED outputs

Support electronic switch and mechanical switch, can control the target, has dimming

function

The dry contact supports: mechanical switch, single on, single off, single on/off,

combination on/off, multi-function, parallel switch type.

Each switch type can set switch mode, dimmable two-way, dimmable increase,

dimmable reduce

Control type: scene, sequence, universal switch, single channel lighting control,

broadcast scene, broadcast channel, curtain switch, GPRS control switch, panel

control, security module, z-audio control

Support security function

Support IEEE.802.15.4

Support online upgrading

Support easy programming

1.3 Device Description

36mm

44mm

Bottom View

Front View

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 2

2. Safety Instructions

The screw down strength should not exceed 0.1Nm

Mounting position: Indoor.

Never let liquids get into the module, it will damage this device.

3. Technical Data

Electric Parameters

Input voltage

AC85~265V, 50/60Hz

Power consumption

0.44w max.

Wireless transmit power

+10dbm

Wireless receive sensitivity

-90dbm

Indoor communication distance

<=30m(barrier free)

RSSI receive signal intensity

>-80dbm

Wireless central frequency

WPAN (China)

780 to 786 MHz

SRD (Europe)

864 to 870 MHz

ISM (North America)

904 to 928 MHz

Default band

780 MHz

Default PSK

HDL-SecurityKey0

Environmental Conditions

Working temperature

-5℃~45℃

Working relative humidity

< 90%

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 3

Storage temperature

-20℃~+60℃

Storage relative humidity

< 93%

Approved

CE

RoHS

Production Information

Dimensions

44×36×17 (mm)

Weight

25.5(g)

Housing material

PC

Installation

Wall box

Protection degree

IP20

Fire and null wire

1.5 mm²(the module provides 15cm wire)

Stripping length

5~7 mm

4. Installation

Antenna

Programming button

4 channels Dry contact

LED indicators for 4

channels

L

N

Programming button: if it is

working properly, the green light

will flicker, press the button three

times continuously, the green

light will flicker quickly, enter the

setup mode (the gateway should

enter the setup mode at the same

time, so that can set the wireless

parameters for it)

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 4

5. Software Configuration

5.1 Wireless Setting via Mesh Gateway

Before user can configure the wireless dimmer normally, need to set the wireless

parameters for it via mesh gateway, and the mesh gateway needs to work in mesh mode.

1- Set the free frequency and unique PSK PWD for the gateway

2- For mesh gateway: press the ‘PROG’ button 3 times continuously, the red LED will flash

quickly that means the gateway enters the wireless setup mode.

3- For wireless dry contact: press the ‘PROG’ button 3 times continuously, the LED will

flicker quickly. It means the wireless dry contact enters the wireless setup mode.

4- Click the ‘Search’ button, the wireless device will be shown.

5- Select the node, you will be able to change its ID and remark it. (the Subnet ID must be

same as the gateway’s).

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 5

6- Click ‘Modify Settings of Selection’, and it will show ‘configurate successful’, then all its

wireless parameters will follow the gateway’s (Band, Frequency and PSK).

7- Click ‘all Node Exit Setup’, then the gateway and the panel will exit the wireless setup

mode.

8- Go to the HDL BUS setup tool’s main interface to search and add the wireless dry

contact, then can start to configure it via the gateway.

5.2 Basic Information

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 6

5.2.1 Change the ID of the device

Every wireless device has one Subnet ID and one Device ID, the Device ID should be

unique in its Subnet and the Subnet ID should be kept consistent with the Mesh Gateway

(HDL-MCIP-RF.10).

5.2.2 Remark

Generally set it like “for living room” to indicate some info.

5.3 Configuration

The setting interface is shown above, setting it is same as setting a panel - select mode

for each key, and set targets/objects to each key. Some modes are unique and you cannot

find them in panels.

5.3.1 Remark

Remarks of dry contacts’ switch, you may make remarks according to the installation

places.

5.3.2 Switch type

Two different Switch types - Momentary and Toggle

You can find two different types of switch from the market.

Momentary Switch - When pressed, it is on, when released, it is off.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 7

If “Electrical switch ”is selected for this kind of switch, a momentary effect can be

produced.

Toggle Switch –It is bi-stable switch, you can set it on or off.

Generally select “Mechanic switch” mode for this kind of switch.

Available modes

Mechanic Switch

Send out a command (generally the on command, e.g., light on.) when Switch is

connected, send out another (generally the off command) when the Switch is

disconnected.

Single on

Assign the Switch can turn on one object only (one channel, or one scene, or one

sequence, etc.)

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 8

Single off

Assign the Switch can turn off one object only (one channel, or one scene, or one

sequence, etc.)

Single on/off

Assign the Switch can turn on/off one object only (one channel, or one scene, or one

sequence, etc.)

Combination on

Assign the Switch can turn on multiple objects (channels, scenes, sequence, etc.)

Combination off

Assign the Switch can turn off multiple objects (channels, scenes, sequence, etc.)

Combination on/off

Assign the Switch can turn on/off multiple objects (channels, scenes, sequence, etc.)

Multi-function

Long press – combination off (or dim, if dimming is enabled in the Wireless Dry Contact

module. Dim the first object only, though.)

Short press – single on/off

Double click – Combination on

This mode can be used in, maybe, meeting, by double-click all the lighting can be on, by

long-press, all lighting can be off, this can avoid mishandling and so it is more secure.

Parallel Switch

This key mode is originally designed for retrofit project where the end-users want to

implement HDL wireless system but they want to reserve the existing toggle buttons, the

toggle buttons are to control one public area lighting (e.g., stair lighting) from multiple

places

Wiring

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 9

Connect the two toggle buttons to two different wireless dry contact channels

Setting

Select “Parallel switch” for both wireless dry contact channels.

5.3.3 Unqualifiedde

Each channel can set the mode

Switch mode: on/off control

Dimmable increase: long press to dim up

Dimmable reduced: long press to dim down

Dimmable two-way: long press to dim up, long press again can dim down

5.3.4 Delay time

Only the “Mechanic switch” switch type has the delay time.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 10

5.3.5 Dimming

Key no. : channel no./ switch no.

Dimming value:

Toggle- when turn on light, the brightness will go to 100%

Memory- save the brightness, when turn on light, the brightness will go to last brightness

before turn off

5.3.6 Target

Can set each channel’s targets.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 11

5.3.7 Low Limit

Set the dimming lower limit.

The Lower limit is useful if you would like to skip the low level segment and dim from a

certain level, say 50%. You want to skip it because maybe lower than 50% is impractical

for you or maybe the load quality is not so good and trembles when at low level segment.

5.3.8 Setting For Keys

Key Enable: enable/disable the channels.

Panel Lock Key Enable: If be selected, can use panel to lock/unlock this channel.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 12

5.4 Security Setting

We can use channels of wireless dry contact to trigger security, like the window state, door

state.

If use wireless dry contact 1 to detect the door state for security, the setting steps as

follow:

a) Select ‘key 1’ here and type in the remark.

b) Enable security function.

c) Input the security module’s Subnet/Device ID, totally 8 areas can be selected, here is

area 1.

For further configuration, please turn to security module’s user manual.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 13

6. Online Upgrade

For the online upgrade, there are two ways, automatic upgrade and manual upgrade.

6.1 Automatic Upgrade

Upgrade steps:

1- Select the online wireless panel that you want to upgrade, click “Read Device Type” to

check its chip type.

2- Select .bin firmware, click “Add Device”, then it will be shown in the upgrade list.

3- Click “Upgrade Selected Device” to start the upgrade.

4- Upgrade finished.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 14

6.2 Manual Upgrade

For manual upgrade, the panel will enter the wireless setup mode, then the mesh gateway

needs to enter the wireless setup mode also.

Upgrade steps:

1- Press the ‘PROG’ button of wireless gateway 3 times continuously to enter the

wireless setup mode.

2- Power off the wireless dry contact, then keep pressing the programming button when

power on it, it will enter the wireless setup mode, and you will be able to read its ID in

the “Device” line.

3- Select .bin firmware , click “Upgrade”.

4- Upgrade finished.

5- Press the ‘PROG’ button of wireless gateway 1 time to exit the wireless setup mode.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 15

7 FAQ

7.1 FAQ001

Q:

HDL-MPS04-RF.18 has indicators for four channels output, but where is the appropriate

place to put those indicators?

A:

Some 3rd party panel has a hold, can put the indicator of MPS04-FR.18 in the hold.

7.2 FAQ002

Q:

MPS04-FR.18 has four led output, what’s the type of led can I connect?

A:

Each led channel is 3.3V 10mA, so you can connect the appropriate led.

User Manual

HDL-MPS04-RF.18

Wireless 4 channels Dry Contact – User Manual 16

8. Note

……………………………………………………………………………………………………….

………………………………………………………………………………………………………

HDL HDL-MPS04-RF.18 User manual

HDL HDL-MPS04-RF.18 User manual

Related papers

Other documents