2. MODWAY
  3. EEI-1199-BRN

MODWAY EEI-1199-BRN Assembly Instructions

  • Hello! I am a chat assistant and I have reviewed the assembly instructions for the modway Dining Table EEI-1199. This document provides a detailed guide on how to assemble your new table, including step-by-step instructions, a hardware checklist and component identification. I am ready to answer any questions you might have based on the provided instructions.
  • How many adults are recommended for assembly?
    What is the approximate assembly time?
    What should I do with packaging and instructions after assembly?
Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 1 of 3
EEI -1199 DINING TABLE
Hardware:
Component:
A Bolt M8x35mm x2
D Allen Wrench x1
1 Table Top x1 2 Leg x2
C Flat Washer x11
Thank you for purchasing the COLUMN TABLE！
！！
！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
3 Central Rail x1 4 Bottom Rail x1
B Bolt M8x50mm x9
1
2
2
3
4
Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 2 of 3
EEI -1199 DINING TABLE
Ax2 Bx2 Cx4
Dx1
STEP 1:
Hardware & Tool required
STEP 2:
Please put the Table Top (1) upside down on a carpeted or padded surface.
Attach Central Rail (3) into the bottom of Table Top (1) by using 3pcs Bolts (B) and 3pcs Flat Washers (C) as
shown. Tighten Bolts (B) by hand.
Attach assembled Legs (2) into the bottom of Table Top (1) by using 4pcs Bolts (B) and 4pcs Flat Washers (C).
Use Allen Wrench (D) to tighten the Bolts (B) clockwise until secure.
Bx7 Cx7 Dx1 Hardware & Tool required
Please put the Legs (2) upside down on a carpeted or padded surface.
Insert Central Rail (3) and Bottom Rail (4) into one of Legs (2).
Use 1pc Bolt (A) and 1pc Flat Washer (C) to connect Bottom Rail (4) and the Leg (2).
Use 1pc Bolt (B) and 1pc Flat Washer (C) to connect Central Rail (3) and the Leg (2).
Use Allen Wrench (D) to tighten the Bolt (A) and Bolt (B) clockwise until secure.
Repeat the same steps for affixing the other Leg(2).
2 2
3
4
1
3
1
1
2
2 2
3
4
24
3
2
Customer Service 908-368-1025︱
︱︱
︱www.modwayfurniture.com Page 3 of 3
EEI -1199 DINING TABLE
STEP 3:
Assembly is completed. The dining table is ready to enjoy now!
Carefully turn over the table.
/