MODWAY EEI-2784-NAT-WHI Assembly Instructions

  • Hello! I've reviewed the provided instructions for the MODWAY desk model EEI-2784. This document outlines the assembly process, including the hardware, components, and steps needed to put the desk together. I'm ready to answer any questions you might have about assembling this desk.
  • How many adults are recommended for assembly?
    What is the approximate assembly time?
    What kind of surface is recommended for assembly?
    Should I throw away the packaging before the assembly is complete?
Customer Service 908-368-1025www.modwayfurniture.com Page 1 of 4
EEI –2784 DESK
Thank you for purchasing the MODWAY DESK
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A Long Bolt M6x75mm x4
B
G Allen Wrench M4 x1
D
Components:
1 Desk Top x1 2 Rail x2
4 Leg x2
3 Leg x2
Medium Bolt M6x65mm x2
Short Bolt M6x20mm x1
1
6 2
3
6 Metal Support Rail x2
4
6
3
4
5
5
5 End Panel x2
C Medium Bolt M6x55mm x4
E Spring Washer M6 x11
F Flat Washer M6 x11
Customer Service 908-368-1025www.modwayfurniture.com Page 2 of 4
EEI –2784 DESK
STEP 1:
STEP 2:
Put Desk Top (1) upside down on a carpeted or padded surface.
Place 2 pieces of Rail (2) to Desk Top (1) as shown.
Insert 4 pieces of Long Bolt (A) with 4 pieces of Spring Washer (E) and 4 pieces of Flat Washer (F) into the pre-drilled holes
on Desk Top (1) through the pre-drilled holes on Rails (2).
Use Allen Wrench (G) to tighten Long Bolts (A) clockwise until secure.
Hardware & Tools required
Hardware & Tools required
Ax4 Ex4
Fx4
Gx1
1
2
E
A
Place 1 piece of Leg I (3), 1 piece of Leg II (4) , and End Panels (5) to the assembled Desk Top (1) and Rails (2) as shown.
Insert 2 pieces of Medium Bolt (C) with 2 pieces of Spring Washer (E) and 2 pieces of Flat Washer (F) into the pre-drilled holes
on the end of Rail (2) through the pre-drilled holes on End panels (5).
Use Allen Wrench (G) to tighten Medium Bolts (C). Do not fully tighten Medium Bolts (C) at this step.
4
1
5
2
F
A
E
F
E
F
E
F
A
A
G
Cx2 Ex2
Fx2
Gx1
2
2
3
5
G
C
E
F
C
E
F
Customer Service 908-368-1025www.modwayfurniture.com Page 3 of 4
EEI –2784 DESK
STEP 3:
STEP 4:
Hardware & Tools required
Hardware & Tools required
Cx2 Ex2
Fx2
Gx1
Place 1 piece of Leg I (3), 1 piece of Leg II (4) , and End Panels (5) to the assembled Desk Top (1) and Rails (2) as shown.
Insert 2 pieces of Medium Bolt (B) with 2 pieces of Spring Washer (E) and 2 pieces of Flat Washer (F) into the pre-drilled holes
on the end of Metal Support Rail (6) through the pre-drilled holes on Legs (3&4).
Insert 1 piece of Short Bolt (D) with 1 piece of Spring Washer (E) and 1 piece of Flat Washer (F) into the pre-drilled holes on
Desk Top (1) through the pre-drilled holes on Metal Support Rails (6) as shown.
Use Allen Wrench (G) to tighten all Medium Bolts (B&C), Long Bolts (A), and Short Bolt (D) clockwise until secure.
5
Bx2 Dx1
Fx3
Gx1
Ex3
Place the remaining 1 piece of Leg I (3), 1 piece of Leg II (4) , and End Panels (5) to the assembled Desk Top (1) , Rails (2),
Leg I (3), and Leg II (4) as shown.
Insert 2 pieces of Medium Bolt (C) with 2 pieces of Spring Washer (E) and 2 pieces of Flat Washer (F) into the pre-drilled holes
on the end of Rail (2) through the pre-drilled holes on End panels (5).
Use Allen Wrench (G) to tighten Medium Bolts (C). Do not fully tighten Medium Bolts (C) at this step.
1
2
2
4
4
3
3
E C
F
G
C
E
F
5
2
2
1
4
4
3
3
6
6 B
E
F
G
D
F
E
G
B
E
F
Customer Service 908-368-1025www.modwayfurniture.com Page 4 of 4
EEI –2784 DESK
STEP 5:
Carefully turn over the assembled desk.
Assembly is complete. Your desk is ready to be used now!
/