ALGE-Timing PS-KP Battery power supply User guide

Brand: ALGE-Timing

Model: PS-KP Battery power supply

Category: Power banks

Type: User guide

ALGE-Timing PS-KP Battery power supply is a universal device that can supply almost all ALGE-TIMING products. You can use it to power ALGE-TIMING timing devices (such as display boards of the D-LINE series) or mobile devices like notebooks or smartphones (using an appropriate adapter). This power bank is also equipped with a 12V car outlet, so you can use it to power car accessories like a portable refrigerator or a tire inflator. Additionally, the PS-KP has a built-in LED light and can be used as a jump starter for cars with a 12-volt battery.

Version-E230509

Manual

Power Bank PS-KP

-2-

Important Information

General

Before using your ALGE-TIMING device read the complete manual carefully. It is part of the device and

contains important information about installation, safety and its intended use. This manual cannot cover

all conceivable applications. For further information or in case of problems that are mentioned not at all

or not sufficiently detailed, please contact your ALGE-TIMING representative. You can find contact details

on our homepage www.alge-timing.com.

Safety

legislator must be taken into account. The device must only be used by trained persons. The setting-up

and installation must only be executed according to the manufacturer’s data.

Never adjust the active speaker system to a very high volume. Permanent high volumes may damage

your hearing! The human ear will get accustomed to high volumes which do not seem to be that high

after some time. Therefore, do not further increase a high volume after getting used to it.

Intended Use

The device must only be used for its intended applications. Technical modifications and any misuse are

prohibited because of the risks involved! ALGE-TIMING is not liable for damages that are caused by im-

proper use or incorrect operation.

Power supply

The stated voltage on the type plate must correspond to voltage of the power source. Check all connec-

tions and plugs before usage. Damaged connection wires must be replaced immediately by an author-

ized electrician. The device must only be connected to an electric supply that has been installed by an

electrician according to IEC 60364-1. Never touch the mains plug with wet hands! Never touch live parts!

Cleaning

Please clean the outside of the device only with a smooth cloth. Detergents can cause damage. Never

submerge in water, never open or clean with wet cloth. The cleaning must not be carried out by hose or

high-pressure (risk of short circuits or other damage).

Liability Limitations

All technical information, data and information for installation and operation correspond to the latest

status at time of printing and are made in all conscience considering our past experience and knowledge.

Information, pictures and description do not entitle to base any claims. The manufacturer is not liable

for damage due to failure to observe the manual, improper use, incorrect repairs, technical modifications,

use of unauthorized spare parts. Translations are made in all conscience. We assume no liability for

translation mistakes, even if the translation is carried out by us or on our behalf.

Disposal

If a label is placed on the device showing a crossed-out dustbin on wheels (see drawing), the European

directive 2002/96/EG applies for this device.

Please get informed about the applicable regulations for separate collection of electrical and electronic

waste in your country and do not dispose of the old devices as household waste. Correct disposal of old

equipment protects the environment and humans against negative consequences!

Manual

Power Bank PS-KP

-3-

Table of Contents

1 General ................................................................................................................ 4

2 Seope of Delivery ................................................................................................ 5

3 Charging of Power Bank PS-KP ........................................................................ 5

3.1 Charging from the Mains ....................................................................................... 5

3.2 Charging in a Car .................................................................................................. 5

3.3 LED- Charging Level Indicator .............................................................................. 5

4 Charging of Devices with the Power Bank PS-KP ............................................ 6

4.1 USB-Output (3) ..................................................................................................... 6

4.1.1 USB3-Connection ............................................................................................................................ 6

4.1.1.1 Power Supply for Mobil Timing MT1 ................................................................................................... 6

4.1.1.2 Power Supply for Teledata TED2 ....................................................................................................... 6

4.2 Output 12 V (9) ..................................................................................................... 7

4.2.1 Standard Cable for 12 V .................................................................................................................. 7

4.2.1.1 Power Supply for Timy3 ...................................................................................................................... 7

4.2.1.2 Power Supply for OPTIc3 ................................................................................................................... 7

4.2.1.3 Power Supply for Printer P6 or P5 ...................................................................................................... 7

4.2.2 Special Cables for 12 V ................................................................................................................... 8

4.2.2.1 Power Supply for Display Board D-LINE (Cable 323-1.5) ................................................................... 8

4.2.2.2 Power Supply for Power Supply D-LINE and WTN-DB (Cable 324-1.5) ............................................. 8

4.2.2.3 Power Supply for Display Board D-LINE and Radar D-RAD (Cable 324-1.5) ..................................... 8

4.2.2.4 Power Supply for Display Board D-LINE and WTN-WS (Cable 324-1.5) ............................................ 8

4.2.2.5 Power Supply for Windspeed WS2 with WTN-WS (Kabel 325-1.5) .................................................... 8

4.2.2.6 Power Supply for Photocell RLS3c (Cable 326-1.5) ........................................................................... 9

4.2.2.7 Power Supply for Older ALGE-TIMING Timing Devices (Cable 326-1.5) ........................................... 9

4.3 Output 19V (8) ...................................................................................................... 9

5 LED-Light ............................................................................................................ 9

5.1 Jump Start for Cars (2) ....................................................................................... 10

6 Reset of the Power Bank PS-KP ...................................................................... 10

7 Maintenance and Care ...................................................................................... 11

8 Causes of Errors ............................................................................................... 11

9 Technical Data .................................................................................................. 12

Subject to changes and misprints

ALGE-TIMING GmbH

Rotkreuzstr. 39

6890 Lustenau / Austria

www.alge-timing.com

Manual

Power Bank PS-KP

-4-

1 General

The Power Bank PS-PK is a universal device that can supply almost all ALGE-TIMING prod-

ucts. The powerful battery of the PS-PK can, for example, supply a D-LINE250-6-E0 with elec-

tricity for up to 8 hours.

All devices that are operated with the PS12A power supply unit can also be operated with the

PS-KP without additional cables. Other ALGE-TIMING devices such as the display boards of

the D-LINE series require a special cable which is not included in the PS-KP set.

1 ...... charging level indicator

2 ...... output: starting aid for cars

3 ...... USB-output 5V/2A

4 ...... USB-output 5V/1A

5 ...... LED-light

6 ...... on-/off switch

(automatic switch-off if not charging

or no consumer is connected)

7 .......input: charging socket 14V/1A

DC-plug 3,5 x 1,3

8 .......output 19V/3A

DC-plug 5,5 x 2,1

(with glued cover to avoid damage to

ALGE-TIMING devices)

9 .......output 12V/10A

for ALGE-TIMING devices

DC-plug 5,5 x2,1

Charging Input 14V/1A

power supply 12 Volt

100–240V car adapter

50/60Hz

12V/10A Start Aid 19V/3.5A USB 5V/2A 12 V/10 A

Output Output Output Output Car Output

ALGE-TIMING jumper cable for notebooks for USB-C- for 12 V

devices with clamps devices car accessory

A: DC-plug 5.5 x 2.1 mm for 12V and 19V output with adapter.

Manual

Power Bank PS-KP

-5-

2 Seope of Delivery

1 x Power Bank PS-KP (jumpstart and power bank)

For Loading of PS-KP:

1 x Charger

(Input (AC): 100V / 240V / Output (DC): 14V / 1A)

1 x Jumpstart Cable

(Input/Output: 14V / 1A (for cigarette lighter)

To Charge Electrical Consumers:

1 x 3-in-1 charger cable (Micro-USB-, Lightning- and USB-C)

1 x Barrel Connector-Adapter-Set (8-pices)

1 x Adapter Cable

To Power 12V Car Accessories:

1 x 12V-Power Outlet

For Storage:

1 x closable Bag

To Start a Vehicle:

1 x Intelligent Jumper Cable for 12-volt vehicles with reverse

polarity protection and boost function

3 Charging of Power Bank PS-KP

Charger: 100 – 240 VAC, output +14 V / 1 A

Operating Voltage: 100-240 VAC with charger or 12V with cigarette lighter cable

Charging Duration: about 5 hours until fully charged

Charging Indication: 5 blue LED

Charging Cycles: about 1000

3.1 Charging from the Mains

A 100-240 VAC charger is included for charging the PS-KP. Plug the charger into the socket

and connect it to the charging socket (7) on the PS-KP. When the LEDs go out, the device is

fully charged.

3.2 Charging in a Car

PS-KP can be charged with the supplied 12 V cigarette lighter charging cable in a car. With

the engine running, plug the car charging cable into the cigarette lighter and plug it into the

charging socket (7) on the PS-KP. When the LEDs go out, the device is fully charged.

3.3 LED- Charging Level Indicator

After switching on, the LED charge status display (1) is displayed for 30 seconds.

LED-Charging Level Indicato

off

5 x blinking

12345

State of Charging empty 10% 20% 40% 60% 80% full

During charging, one LED flashes and indicates the charging status. All LEDs go out when the

charging process has been aborted or the battery is full. If no LED lights up when switching

on, the PS-KP must be charged before commissioning. It must not be stored in this condition.

Manual

Power Bank PS-KP

-6-

4 Charging of Devices with the Power Bank PS-KP

4.1 USB-Output (3)

All devices with USB cable can be charged via the USB connection (3) with 5V/2A.

With the 3-in-1 charging cable included in the delivery, all digital devices with a Micro-USB

connection, Lightning plug and USB-C connector can be charged. This includes Mobil Timing

MT1, Teledata Ted2 or Printer P6-USB.

• Connect consumer devices (e.g. Mobile Timing MT1) to USB output (3).

• Briefly press the on button (6).

• As long as power is being drawn, the charge status of the battery is indicated by the

blue LED (1).

• If the device is charged or if it is separated from the PS-KP, the LED will switch off.

• In the event of an overload or short circuit, the PS-KP switches off.

• Both USB outputs (3) and (4) can be used simultaneously.

4.1.1 USB3-Connection

The large USB plug (USB 3.0) is plugged into the PS-KP (3). The

USB-Type C connector is plugged into the ALGE-TIMING device.

4.1.1.1 Power Supply for Mobil Timing MT1

4.1.1.2 Power Supply for Teledata TED2

Manual

Power Bank PS-KP

-7-

4.2 Output 12 V (9)

12 V products from ALGE-TIMING, such as Timy3, OP-TIc3, D-LINE, can be operated via

the Output 12 V/10A (9).

• Connect consumers (e.g. OPTIc3) to the 12 V output (9).

• The consumer device is connected directly to the PS-KP battery (it is not neces-

sary to switch it on, the LED for the battery indicator only lights up for 30 seconds

if you press the on switch (6) briefly.

Note: Devices such as 12V-compressors, 12V-fans or 12V-vacuum cleaners must ensure that

their starting current does not exceed 10 A. If the starting current is exceeded, the safety func-

tion of the PS-KP switches the device off. This technical information can be found in the in-

structions or requested from the respective manufacturer.

4.2.1 Standard Cable for 12 V

The 12V-cable 328-2 (24 cm long) and an extension cable is

included in the set of the PS-KP.

4.2.1.1 Power Supply for Timy3

4.2.1.2 Power Supply for OPTIc3

4.2.1.3 Power Supply for Printer P6 or P5

Manual

Power Bank PS-KP

-8-

4.2.2 Special Cables for 12 V

These 12 V cables are not included in the set and must be ordered separately.

4.2.2.1 Power Supply for Display Board D-LINE (Cable 323-1.5)

4.2.2.2 Power Supply for Power Supply D-LINE and WTN-DB (Cable 324-1.5)

4.2.2.3 Power Supply for Display Board D-LINE and Radar D-RAD (Cable 324-1.5)

4.2.2.4 Power Supply for Display Board D-LINE and WTN-WS (Cable 324-1.5)

4.2.2.5 Power Supply for Windspeed WS2 with WTN-WS (Kabel 325-1.5)

Manual

Power Bank PS-KP

-9-

4.2.2.6 Power Supply for Photocell RLS3c (Cable 326-1.5)

4.2.2.7 Power Supply for Older ALGE-TIMING Timing Devices (Cable 326-1.5)

4.3 Output 19V (8)

Notebooks and laptops can be charged via the Output 19V/3.5A (8). All standard adapters

are included in the 8-piece adapter set, including the adapter cable.

Attention: This socket is sealed with a cover so that a 12V device from ALGE-TIMING will

not be charged with 19V volt and accidentally destroyed.

5 LED-Light

The PS-PK has a built-in LED-light with various functions:

• Press the power button for 3 seconds: steady light (flashlight function)

• Then briefly press the power button: flashing

• Then briefly press the power button: SOS (3 x short, 3 x long in succession)

• Then briefly press the on button: the light is switched off

Manual

Power Bank PS-KP

-10-

5.1 Jump Start for Cars (2)

The PS-KP can also be used to start cars with dead batteries.

The jump start process may take a maximum of 10 seconds. Then the PS-KP has to cool

down for 30 seconds. If these values are not observed, the device or parts of it can be

destroyed.

If the engine does not start after 3 attempts, you should look for the cause of the fault on the

vehicle before making further starting attempts.

• Connect the jump starter with the blue plug to the PS-KP.

Caution: make sure it is firmly seated and push the socket in completely!

• Connect the red clamp to the car battery (+).

• Connect the black clamp to the car battery (-).

• When the green LED on the jumper cable lights up, you can start the engine.

• If the red LED on the jumper cable lights up and a warning buzzer can be heard, then

the battery has the wrong polarity and the red and black clamps on the battery must be

swapped.

• If the green LED on the jumper cable flashes and the warning buzzer sounds, the car

battery is completely empty. In this case, the boost button on the charging cable must be

pressed and started within 30 seconds. Pay attention to a maximum start time of 10 sec-

onds / 30 seconds break! In this situation, the PS-PK has a strong load.

• No LED display and no warning buzzer: Either the connection to the car battery termi-

nal is not tight enough or the battery is completely discharged or defective. Proceed as

above (green LED flashes).

Attention - Warning:

Do not touch the clamps while the "Boost" button is pressed. There is a strong formation of

sparks and there is a risk of explosion. The device will be destroyed.

6 Reset of the Power Bank PS-KP

If the output 12V/10A (9) and the output 19V/3.5A (8) are overloaded, the PS-KP automati-

cally switches off the respective output for its own protection. In order to reset the device, a

voltage must be present at the 14V/1A charging socket (7) (connect the power pack).

If no charging voltage is available (e.g. when using outdoors), proceed as follows:

• Connect the jumper clamps to the cigarette lighter cable. The black terminal clamp (-)

is connected to the outside of the ground connection of the plug from the cigarette

lighter cable and the red terminal clamp (+) is connected in the middle to the positive

pole of the plug.

• Briefly press the Boost button. The flashlight flashes and the blue LEDs confirm the

reset from the device.

Attention: Caution is advised, as the terminal clamps have voltage and damage

and sparks can occur in the event of a short circuit.

Manual

Power Bank PS-KP

-11-

7 Maintenance and Care

Before use, check the PS-KP including accessories and cables for damage. If a damage is

found, the device must not be put into operation.

Storage:

Disconnect the device from the charging cable or the 230 Volt mains adapter. Occasionally

you can wipe the PS-KP with a slightly damp cloth. Do not use solvents or harsh cleaning

supplies. With the cable disconnected, clean the pole terminals at the contact points with a

brush and lightly grease them.

Charge the device at regular intervals as described several times.

If the PS-KP is discharged below a critical value during storage, a protective circuit ensures

that charging is no longer possible. The device is therefore irreparably defective and must be

disposed of. This process is verifiable and is not covered by the guarantee

8 Causes of Errors

• No blue LED lights up after switching on: The battery is not charged and the PS-KP

must be charged immediately with the 230V mains adapter!

• PS-KP gets hot during operation: If the maximum performance of the PS-KP is re-

quired, the device heats up. If 2 USB consumers are connected, then remove one. If a

notebook is being operated, remove the notebook's battery, this reduces the power

consumption to the pure operating consumption of the notebook without charging the

battery.

• The 230V power supply can also heat up during operation. This is permissible as long

as the device is slightly more than lukewarm. If it gets hot, it should be unplugged im-

mediately and allowed to cool down. Due to overload, never put the 230V mains

adapter into operation and connect consumers to the device at the same time. If the

charger gets hot despite these measures, there is a defect and the charger must be

disconnected from the 230 Volt mains voltage and replaced.

• The device cannot be charged via the cigarette lighter: Check the fuse in the charging

cable plug (unscrew the tip of the plug. Pull out the fuse (type F2A, 5 x 20 mm)).

Manual

Power Bank PS-KP

-12-

9 Technical Data

Battery Type: Lithium Rechargeable Battery

Capacity: 66.6 Wh, 18 Ah (consisting of 3 individual cells: 3 x 6 Ah)

Charging Input: 14 VDC / 1 A

Power Supply: 100 – 240 VAC, max. 0.6 A; output +14 V / 1 A

Operating Voltage: 230V with power supply and 12V with cigarette lighter

Charging Time: about 5 hours until fully charged

Charging Indicator: 5 blue LED

Charging Cycles: about 1000

Output:  5V/1A (USB for mobile phone)

 5V/2A (USB for MT1, TED2, P6-USB, tablets, smartphones etc.)

 12V/10A, max. 120 W (for ALGE-TIMING devices with 12V input)

 19V/3.5A, max. 66 W, electronically secured (not in function)

 12V-Jumper Cable Outlet

Jump Start Current: at 12 V 300 A up to 10 Seconds

Peak Current 12V: 600 A about 1 Second

Cooling Time: at least 30 seconds after attempting to start

Starting Attempts: max. 3, then check for problem

max. 20 starting attempts at fully charged battery

Operation Temperature: -20°C to 60°C

Storage Temperature: +10°C to 60°C

optimal storage temperature at +15 – 18°C

never store in direct sunlight

Storage Duration: max. 6 to 12 month with low self-discharge

To ensure a long service life, the device should be recharged every 3

months.

Recharge before storage and before use.

Never store the device with the jumper cable connected!

LED-Light: 1 W LED

Measurements: 230 x 87 x 27 mm

Weight: about 0.6 kg

CE conformity: The device meets the CE requirements. The declaration of conformity

can be downloaded from www.alge-timing.com.

ALGE-TIMING

GmbH

Rotkreuzstrasse 39

A-6890 Lustenau

Austria

Tel: +43-5577-85966

Fax: +43-5577-85966-4

office@alge-timing.com

www.alge-timing.com

ALGE-Timing PS-KP Battery power supply User guide

Brand: ALGE-Timing

Model: PS-KP Battery power supply

Category: Power banks

Type: User guide

Download PDF

report

ALGE-Timing PS-KP Battery power supply User guide

ALGE-Timing PS-KP Battery power supply User guide

Related papers

Other documents