Symmons SLW-6712-1.0 Installation guide

Identity

™

WARNING: This product can expose you to chemicals

including lead, which is known to the state of California to

cause cancer, birth defects, or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

Model Numbers

Two Handle Widespread Lavatory Faucet

Operation & Maintenance Manual

SLW-6710-1.5, SLW-6712-1.5

Two handle widespread lavatory faucet features 8"-16"

mount, ceramic cartridges, 1/2" IPS inlet connections,

50/50 pop-up drain assembly and standard 1.5 gpm

(5.7 L/min) aerator. Faucet constructed from brass, plated

in standard polished chrome nish.

Speciﬁcation



SLW-6710-1.5

Two Handle Widespread Lavatory Faucet



SLW-6712-1.5

Two Handle Widespread Lavatory Faucet with lift

rod and 50/50 pop-up drain assembly

Dimensions

Measurements

A 13-1/2", 343 mm

B 8", 203 mm

C 4", 102 mm

D (2x) 2-1/8", 54 mm

E

Deck Thickness Ref.

Min. 5/8", 16 mm

Max. 1-3/8", 35 mm

F

(2x) Hole Size

Min. Ø 1-1/4", 32 mm

Max. Ø 1-1/2", 38 mm

G

Hole Size

Min. Ø 1-3/8", 35 mm

Max. Ø 1-5/8", 41 mm

H

4-5/16", 110 mm

I

2", 51 mm

J

4-5/8", 117 mm

K

3-5/8", 92 mm

Note: Dimensions subject to change without notice.

Modiﬁcations

Note: Append appropriate -sufx to model number.



-0.5 0.5 gpm (1.9 L/min) aerator



-1.0 1.0 gpm (3.8 L/min) aerator



-Delete

Sufﬁx 1.5

2.2 gpm (8.3 L/min) aerator



-MP Metal pop-up drain in place of standard



-STN Satin Nickel ﬁnish



-VP Vandal resistant aerator

CG

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Compliance

-ASME A112.18.1/CSA B125.1

-NSF/ANSI 61.9, NSF/ANSI 372

-WaterSense 1.5 gpm & 1.0 gpm

Certied by

CSA Group

AA

KK

JJ

BB

HH

EE

DD

FF

GG

II

CC

2

*Note: Append -STN to part number for Satin Nickel

nish.

Replacement Parts

Item Description Part Number

A Lift Rod RL-286*

B

C

Handle

Set Screw

RL-287*

F

Aerator Kit (2.2)

Aerator Kit (1.5)

Aerator Kit (1.0)

Laminar Flow Kit (2.2)

Laminar Flow Kit (1.5)

Laminar Flow Kit (1.0)

Laminar Flow Kit (0.5)

Vandal Proof Kit (2.2)

Vandal Proof Kit (1.5)

Vandal Proof Kit (1.0)

Vandal Proof Kit (0.5)

LN-15*

FLR-110-1.5*

FLR-110-1.0*

RL-019-2.2*

RL-019-1.5*

RL-019-1.0*

RL-019*

RL-315-2.2*

RL-315-1.5*

RL-315-1.0*

RL-315-0.5*

H Hot Cartridge RL-075

I Cold Cartridge RL-076

L

M

O

Mounting Hardware,

Spout

RL-123

R

S

U

Mounting Hardware,

Valve Body

RL-211

V

50/50 Pop-Up

Drain Assembly

RL-223*

Tools Required

Adjustable Wrench

Allen Wrench (3/32")

Plumber Putty

Plumber Tape

PLUMBER

PUTTY

Parts Breakdown

V

V1

V2

V3

V5

V6

V7

V4

V8

V9

V11

V10

V12

V14

V13

T

C

A

D

E

F

G

J

L

M

N

K

O

U

Q

R

S

P

H

I

B

If replacing an older faucet ensure water supply is

turned OFF before removing, then turn faucet control

valve ON to relieve water pressure.

DO NOT use pipe dope or thread sealant on drain

assembly, or any plastic threaded components.

3

Installation

1

3

2

V1

V2

V7

ROD INLET

2) Turn tail piece (V7) and ange (V2)

so rod inlet is facing toward faucet.

Pull assembly down into drain hole.

Secure hardware from below sink.

Install stopper (V1) in the removable

or non-removable position.

1) Seat ange (V2) into sink. Install

gasket (V4), washer (V5) and nut (V6)

onto ange from below sink, but do

not secure nut. Screw on tail piece (V7)

and hand tighten.

2

3

1

V2

V3

V5

V6

V7

V4

OPTIONAL

PLUMBER

PUTTY

3) Attach inner washer (V8), pivot

rod (V9) and outer washer (V10) to

tail piece (V7). Hand tighten rod

nut (V11) to secure pivot rod (V9).

1

V7

V8

V9

V11

V10

N

4) Insert valve bodies (N) through sink

holes.

5) Install washer (R) and mounting

nut (S) to valve body (N). Secure

with screws (U).

1

N

R

S

U

6) Insert spout body (D) through sink

hole. Attach rubber washer (L)

and metal washer (M) to threaded

rod on spout body. Secure with

mounting nut (O).

L

1

D

2

M

3

O

7) Connect lift rod (A) to clevis strap (V13)

and secure with thumb screw (V14).

A

V13

1

2

V14

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621

Installation

8) Insert pivot rod (V9) through spring

clip (V12) and clevis strap (V13).

Secure with spring clip (V12).

Adjust linkage if necessary.

9) Connect hoses (T) to spout and

valve body water connections

(K and P).

Maintenance

1) Turn off water supply. Loosen and

remove the handle set screw (C)

and handle (B).

2

C

B

1

3) Remove cartridge (H and/or I)

and inspect for debris. Replace

cartridge if necessary.

4) Install cartridge following steps

1 & 2 in reverse.

H I

Problem Cause Solution

Finish is spotting.

Elements in water supply may cause

water staining on nish.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.

Troubleshooting Chart

1

V9

2

V12

V13

1

T

1

K

P

10) Using a wrench, attach supply

lines to IPS inlet connections (Q)

and shut off valves. DO NOT

overtighten.

1

2

3

4

Q

11) Turn on water supplies. Remove

aerator (F) and ush lines free of

debris. Check for leaks.

2) Remove escutcheon (E) and nut (G).

2

E

1

G

Page is loading ...

Symmons SLW-6712-1.0 Installation guide

This manual is also suitable for

Symmons SLW-6712-1.0 Installation guide

in other languages

Related papers

Other documents