8
en Settings
4. Pressandholdbuttons
B (11) and
A(12)simultaneouslyforatleast
5seconds.Either “off”or “on”
lightsup.
5. Pressthestartbutton(10)toselect“on”.
6. Pressandholdthestartbutton(10)for
atleast5secondstoconrm.Allofthe
LEDslightupbriey.
7. LED DashesandLEDFlightsup.
8. Placeacontainerwithacapacity
of0.5litresunderthemilkfrother
outlet(6).
9. Pulloutthemilkfrother(6)toopenit.
LED Fashes.
10.Waterwillnowowthroughthelterand
rinseit.
11.When LED Flightsupconstantly,
pressinthemilkfrother(6)tocloseit.
12.Emptythecontainer.
Theapplianceisreadytouseagain.
Information:Rinsingtheltersimultaneously
activatesthesettingforthechangelter
display (= LED Dashes).
Thelterisnolongereffectivewhenthe
changelterdisplayappears,oratthe
latestaftertwomonths.Itneedstobe
replaced for reasons of hygiene and so
thatthereisnobuild-upoflimescale(this
coulddamagetheappliance).Replacement
lterscanbeobtainedfromretailersorfrom
customerservice(see“Accessories”).Ifno
newlterisinserted,changethesettingfor
thelter(see“Waterhardness”).
Information:Youcanusethelterindicator
tomarkthemonthinwhichyouinserted
thelter.Youcanalsomarkthemonthin
whichyouwillneedtoreplacethelternext
(atthelatestaftertwomonths).
Information:Iftheappliancehasnotbeen
usedforaprolongedperiod(forexample,
whenyouareonvacation),theexistinglter
shouldberinsedbeforetheapplianceis
usedagain.Todoso,dispenseacupofhot
waterandpouritaway.
Settings
Youcancustomizethesettingsonthe
appliance.
Youcanmakethefollowingadjustments:
Water hardness
Thewaterhardnesssettingcanbeadjusted
onthisappliance.Itisimportanttoset
thewaterhardnesscorrectlysothatthe
appliancecanaccuratelyindicatewhenitis
timetorunthedescaleprocess.Thefactory
settingforthewaterhardnessis4.Youcan
establishthewaterhardnesseitherbyusing
theteststripprovidedorbyaskingyourlocal
waterprovider.
Diptheteststripinthewaterbriey,shake
itgentlyandchecktheresultafterone
minute.
Level Waterhardness
German(°dH) French (°fH)
1
2
3
4
1-7
8-14
15-21
22-30
1-13
14-25
26-38
39-54
Ifyouwishtochangethedefaultdegreeof
waterhardness,orifyouhaveinserteda
waterlter,proceedasfollows:
1. Turntherotary
knob(13)toposition
2. PressandholdbuttonsB (11) and
A(12)simultaneouslyforatleast
5seconds.Thesetwaterhardnessis
indicatedbythenumberofLEDsthat
nowlightup.
3. Nowpressthestartbutton(10)repeat-
edlyuntiltherequiredwaterhardness
isindicated,e.g.,forwaterhardness3,
LEDs D, E and Fwilllightup.