SPX INDOORTRAINING CYCLE
ASSEMBLY MANUAL
MODEL: VF803J
Questions?
As
a quality
home
gym supplier
wt'
are committed to your complete satisfaction. 1[you have questions, or
find
missing
or
damaged
parts,
we
will g&UlffIIIUe your
CQmplete
satisfaction through
our
authorized
detJJer
service centers or our home
offia
customo
.service
department. Please
coU
your
/oaJ1
deDler
for
assistance
or
BODYCRAFT
at
800-990-5556
(9:00AM
- 5:00 PM).
Our
trained tedlaniciallS will provide
immediate assistance
to
you,
free
of
charge.
We
stand behind
OUT
products. Every piece, every part
of
this
BODYCRAFT
strenglh
troining
system
is
pranlud
for
as
long
4S
you own iI.
We
will repair
or
repltlce anything that
goes
wrong.
Bodycraft is a division
of
Recreation Supply Inc.
p.
0. Box
lSI
S/#Ibwy,
OH
43074
BEFORE
YOU
BEGIN
Congratulations and thank you for selecting the BODYCRAFT SPX
INDOOR
TRAINING CYCLE. The SPX
INDOOR
TRAINING
CYCLE
offers an
impressive array
of
cardio training exercises to develop lower body muscle
group
of
the body and tone up your cardio fitness.
Whether your goal is cardiovascular fitness, a shapely, toned body or dramatic
muscle size and strength, the
SPX.
INDOOR
TRAINING
CYCLE
will help
you achieve the specific results you want.
For your safety and benefits, read this manual and the accompanying literature
before using the SPX
INDOOR
TRAINING
CYCLE. Keep this manual for future
reference.
If
you have additional questions, please call your· local BODY
CRAFT
dealers or our customer service department at 800-990-5556 Monday through
Friday, 9 a.m. until 5 p.m. Eastern Time.
~PORTANTSAFETYNOTES
Tbere
is a risk assumed by individuals wbn use this type
of
equipment.
Before beginning tbis
or
any
otber
exercise program consult your pbysician.
This
is
especially important for individuals over tbe age
of
35
or
persons
witb pre-existing bealtb problems. Recreation Supply, Inc. assumes no
responsibility for personal
injury
or
property damage sustained by
or
tbrougb use
of
this product.
1.
This product must be assembled on a flat, level surface to assure its
proper function.
2.
Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
3.
Keep children away from the SPX
INDOOR
TRAINING
CYCLE
at all
times.
4.
Keep your hands away
from
flywheel and all moving parts.
5.
When adjusting the seat post and handlebar post slowly to avoid your
fingers not pinching
by
seat post
or
handlebar stem and seat
is
tighten by
Lock Lever.
If
not, the seat may slip -and cause injury.
6.
Wear soft jogging shoes and put your foot as far forward as you can to
toe-clip, use
two bands to adjust' the strap
of
pedal to tighten.
7. Do Not raised Handlebar Stem and Seat Post above SAFETY LINE.
Failure to do so may result in serious injury.
8.
If
unsure about the proper use
of
the SPX
INDOOR
TRAINING
CYCLE
cardio training system call your local BODYCRAFT dealer
or
our customer
service department at 800-990-5556.
EXPLODEDl
23
18
6
15
111
62R
</.'73
,
73
7R
71
72
EXPLODED 2
14
,~~
9
NO.
DESCRIPTION
• OTY.
1 Main Frame
1
2 Rear Stabilizer
1
3
M8 X 4" Domed Bolt 4
4 M8 Washer
4
5 M8 Domed Nut
4
6
. Front Stabilizer
1
71.1
R)
Pedal
1
8
M8Nut
1
9 Bottle Caoe
2
10 "
Bottle Caoe Fixed Screw 4
11
Handle Bar
,
1
12
Seat Clamp 1
13
Busino for Handle Stem and Seat Post 6
14 Stainless Steel Handle Bar Stem
1
15 Stainless Steel Seat Post
1
16
Seat Sliding Housing 1
17
Seat (Saddle) 1
18 Lock Lever
4
19 23L Lock Nut
2
20
V Lock fixed Screw
2
21
V Block
2
22
V Block fixed Screw
4
23
Plastic Sleeve
8
24 Nvlon Sleeve
1
25
3/8" Nut
1
26 M20 Nut
1
27
Adj. Knob 1
28
' 34L Busing
1
29
M8 Lock Nut
1
30
Round Plate
2
31
20L Sorino
1
32·
Axle
1
32A Lower Stud.
1
33
M8 X 5/16" Guide Screw
1
34
M6 Nut
1
35
Spacer 1
36
6004ZZ Bearing
4
37
Rear Stabilizer End Cap
2
38
Flywheel Axle
.
1
39
Flywheel
1
40
M17 X 5/16" Lock Nut 2
NO.
DESCRIPTION
OTY.
41
Brake Pad
1
42
M6
X 3/4" Screw
1
43 M6 Washer
1
44 M6 Nut 1
45
Brake Arm
1
46 Brake Sleeve
1
47
4.5L SprinQ
1
48
"U" Sleeve
1
49 M6 X 1·1/4" Bolt
1
50
M6 X 4-3/4" Adj. Screw
2
51
M10 Washer 2
52
M10 Domed Nut
2
53
PU
Transportation Wheel
2
54
3/8" X 5/8" Bolt
,
2
55
608ZZ Bearina
4
56 M6 Bolt Nut
2
57
M6 X 1/2" Bolt Nut
2
58
Front Stabilizer End Cap
2
59 Belt 1
60
2400
Sleeve 1
61
Main Frame Axle
1
62L
Left Crank (pre-assembled)
1
62R
Right Crank (pre-assembled)
1
63
Flange Nut
2
64
Dustv Cover
2'
65
' M10 X 5/8" Bolt
4
66
Spnna Washer
4
67 Belt Wheel
1
68 Inner Belt Cover
,
1
69
~
...
M5 X 3/8" Screw
1
I
11*
M5 Smeller Washer
2
M5 LarQer Washer
.
2
.
'Y
72-
Outer Belt Cover
1
73 M5 X 3/8" Screw
5
74'::?'
M5 X 5/8" Screw
2
75 3/8" Adj, Screw
2
76
3/8" Nut
2
77
78
79
80
STEP 1 FRONT AND REAR STABILIZER
1.
Attach Rear Stabilizer(2) and Front Stabilizer (6) to Main
Frame (1) on a
flat level surface floor, using two M8 X 4"
Domed Bolts (3), two M8 Washers (4) and two
M8
Domed
Nuts (5) on each.
2. There are height adjusters underneath the End Caps
(37,58) installed on the Front and Rear Stabilizers that
need to be adjusted until the bike is totally
staole on the
floor.
FRONT
REAR
37
3
~~537
4
75-
......"
STEP 2 ASSEMBLE PEDALS
1.
Carefully align the threads
of
the axle on the Right Pedal (7R)
("R" on end
of
axle) with the threaded hole on the right crank
arm and screw in clockwise by hand. Tighten the pedal to the
crank arm using a 15mm wrench.
2.
Repeat the procedure for the left side. but screw the Left Pedal
(7L) in counter-clockwise.
PEDAL
STEP
3
ASSEMBLE
HANDLE
BAR
AND
STEM
1.
Insert the Stainless Steel Handlebar Stem (14) into the Front
Tube
of
Bike (1), adjust the height according to your personal
height above the SAFETY LINE, tighten by Lock Lever (18).
Note:
Pull
the Lever
of
Lock Lever (18) backward and then
release to adjust the angle
of
Lever you desired.
2. Remove the pre-installed V-Lock fixed screw (20) in the
front
handlebar stem and then slide the Handlebar (11) onto the
Stainless Steel Handlebar Stem (14) and tighten using the
Lock Lever (18). Re-insert the V-Lock screw and tighten.
HANDLEBAR
20 :
~18
11
STEP 4 ASSEMBLE SEAT AND SEAT POST
1.
Insert the Seat Post (15)
intothe
Rear Tube
of
Bike (1), adjust
the height according to your perSonal height above the
SAFETY LINE, tighten by Lock Lever (18).
Note: Pull lever
of
Lock Lever (18) backward and then release
to adjust the angle
of
Lever.
2.
Remove the pre-installed V-Lock fixed Screw (20) on rear
of
Stainless Steel Seat Post (15) and slide the Seat Sliding
Housing (16) onto the Stainless Steel Seat Post (15), tighten
by Lock Lever (18). Re-insert the V-Lock fixed screw and
tighten.
SEAT
IS
.
22
~
.,
18
17
STEP 5 ASSEMBLE BOTTLE CAGE
•
1.
Attach a Bottle Cage (9) to each side
of
the front forks and
secure using the Bottle Cage Fixed Screws
(10).'
RIGHT
LEFT
•
·
•
/
