DVR-H200UK
INSTRUCTION MANUAL
HDD/DVD Recorder
Call 0870 240 7475
Problems with set-up?
Call 0870 240 7475
Calls cost a maximum of 8p per
minute during peak periods,
based on BT rates of April 2004.
GETTING STARTED
Accessories .................................................................. 1
Important safety instructions ................................... 2
Warnings, cautions and others ................................. 3
Disc information ........................................................... 4
CONTROLS AND DISPLAYS
Remote control ............................................................. 5
Front panel connections ............................................. 6
Display window ............................................................. 6
Rear panel connections .............................................. 7
CONNECTIONS
Connecting the antenna cable and television ........ 8
For better video quality............................................... 9
Component out ......................................................... 9
For better audio quality............................................. 10
Connection to a stereo audio amplifier or receiver 10
Connection to a digital audio device ...................... 10
Digital out optical .................................................... 10
Digital out coaxial ................................................... 10
SETTING UP
Setup menu ................................................................. 11
TV CHANNEL SETUP
TV channel search ..................................................... 12
Fine-tuning TV channels manually ......................... 12
Editing TV channels manually.................................. 12
Channel Editor ............................................................. 13
SETTING UP VIDEO PLUS+ SYSTEM
Setting up VIDEO Plus+
®
System ............................ 14
EASY GUIDER
Playback ....................................................................... 15
Record .......................................................................... 16
Timer record ............................................................... 17
Copy .............................................................................. 19
RECORDING
Before recording ........................................................ 20
Recording television programs .............................. 20
Adding new recordings ............................................ 21
Changing chapter intervals...................................... 21
Playing back the last recorded session................ 21
Recording from a VCR or Camcorder .................... 22
One touch record ....................................................... 23
DV recording ............................................................... 23
DV control .................................................................... 24
Recording on a CD-R/CD-RW disc ............................ 25
TIMER RECORDING
Setting the timer ........................................................ 26
Recording TV programs with VIDEO Plus+
®
System . 27
TABLE OF CONTENTS
TIME SHIFT
Pausing Live TV Broadcast ...................................... 29
Record and Play .......................................................... 29
PLAYBACK
Basic playback ........................................................... 30
POWER, OPEN/CLOSE, PLAY, FF, REV ................. 30
NEXT, PREVIOUS ................................................... 30
PAUSE/STEP, STOP, DISPLAY ............................... 30
DISC MENU, PLAYLIST .......................................... 30
Navigation operation ................................................. 31
REPEAT, ZOOM ...................................................... 31
SLOW, SEARCH .................................................... 31
A-B REPEAT,SUBTITLE .......................................... 31
AUDIO, ANGLE ....................................................... 31
INFORMATION ........................................................ 31
Video title playback .................................................. 32
Music file playback ................................................... 33
Picture file playback ................................................. 33
Audio CD playback .................................................... 34
Playback pictures with music ................................ 34
COPY
Copy from DVD to HDD .............................................. 35
Copy from HDD to DVD .............................................. 35
EDIT
DVD menu and Edit menu ........................................ 36
Naming a title ............................................................. 36
Protecting a title ........................................................ 36
Overwriting a title ..................................................... 36
Splitting a title ............................................................ 37
Merging titles ............................................................ 37
Erasing a title ............................................................. 37
Setting a title thumbnail .......................................... 37
Chapter marks relevant setting ............................ 38
DISC TOOLS
Erase ............................................................................. 40
Finalize.......................................................................... 40
Clean up ....................................................................... 41
Defragment.................................................................. 41
GUI OPERATION
FIRMWARE UPDATE
GLOSSARY
SPECIFICATIONS
TROUBLESHOTTING GUIDE
®
Accessories
Please check and identify the supplied accessories.
1x Remote control
1x Audio/Video cable
1x Power Cord
2x Batteries
1x RF Cable
Used batteries
The batteries in the remote controller of your
HDD/DVD Recorder do not contain mercury.
However, Sanyo recommends that you do not
dispose of used batteries with domestic refuse.
Please, contact your dealer or your local
authorities for information regarding the disposal
of used batteries or take them to your nearest
collection point.
2
1) Read instructionss. Read all the safety and operating
instructions before operating the product.
2) Retain instructionss. Keep the safety and operating
instructions for future reference.
3) Heed warningss. Adhere to all warnings on the product and in
the operating instructions.
4) Follow instructionss. Follow all operating and use
instructions.
5) Cleaningg-Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
6) Attachmentss-Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
7) Water and Moisturee-Do not use this product near water
for example, near a bathtub, washbowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool.
8) Accessoriess-Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the product.
Any mounting of the product should follow the manufacturer’s
instructions and should use a mounting accessory recom-
mended by the manufacturer.
9) CARTT-A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
10) Ventilationn-Slots and openings in the cabinet provide
ventilation, ensure reliable operation of the product, and protect
it from overheating. Do not block or cover these openings. The
openings should never be blocked by placing the product on a
bed, sofa, rug, or other similar surface. Do not place this
product in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
11) Power Sourcess-This product should be operated only from
the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer
to the operating instructions.
12) LOCATIONN-The appliance should be installed in a stable
location.
13) NONUSE P
ERIODSS-The power cord of the appliance
should be unplugged from the outlet when left unused for a
long period of time.
14) Grounding or Polarizationn-
• If this product is equipped with a polarized alternating current
line plug (a plug having one blade wider than the other), it will fit
into the outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of
the polarized plug.
• If this product is equipped with a three-wire grounding type plug,
it will only fit into a grounding type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding type plug.
15) Power-Cord Protectionn-Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point
where they exit from the product.
16) Outdoor Antenna Groundingg-If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
17)
Lightningg-For added protection of this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
18) Power Liness-An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
lights or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna system,
take extreme care to keep it from touching power lines or
circuits. Contact with them might be fatal.
19) Overloadingg-Do not overload wall outlets, extension cords,
or integral convenience receptacles. This can result in a risk of
fire or electric shock.
20) ObjectssandLiquids-Do not push objects of any kind into
this product through openings. They may touch dangerous
voltage points or short out parts, resulting in a fire or electric
shock. Liquids of any kind should not be used on or around
this product.
21) Servicingg-Do not attempt to service this product yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service
personnel.
22) Damage Requiring Servicee-Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
• When the power supply cord or plug is damaged,
• If liquid has spilled or objects have fallen into the product,
• If the product has been exposed to rain or water,
• If the product does not function properly after following the
operating instructions, contact Customer Service for technical
support.
• If the product has been dropped or damaged in any way,
• When the product exhibits a distinct change in performance.
This indicates a need for service.
23) Replacement Partss-When replacement parts are required,
be sure the service technician uses replacement parts
specified by the manufacturer or having the same characteris-
tics as the original part. Unauthorized substitutions may result
in fire, electric shock, or other hazards.
24) Safety Checkk-Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
25) Wall or Ceiling Mountingg-Mount the product to a wall or
ceiling only as recommended by the manufacturer.
26) Heatt- Keep this product away from heat sources, such as
radiators, heat registers, stoves, or amplifiers.
27) Battery Usagee- Battery leakage may result in bodily injury or
damage to the unit. In order to avoid battery problems, please
follow these instructions.
• Install all batteries correctly, with + and - aligned as marked on
the unit.
• Do not mix batteries (old/new, carbon/alkaline, etc.).
• Remove batteries when the unit is not used for a long time.
IMPORTANT SAFETY INSTRUCTIONS
3
WARNINGS,CAUTIONS AND OTHERS
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT
OPEN THE COVER AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS
TO MOISTURE AND ENSURE THAT OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED AWAY
FROM THE APPARATUS.
CAUTION! –– STANDBY/ON button
Disconnect the main plug to shut the power off
completely. The
STANDBY/ON button in any position
does not disconnect the main line. Power can be
controlled from the remote.
CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER OF THIS UNIT.
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
PRODUCTS WITH 625P PROGRESSIVE SCAN OUTPUTS
NOTICE REQUIREMENTS
“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINI-
TION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS
PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN
THE PICTURE. IN CASE OF 625 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE “STANDARD DEFINITION”
OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV
SET COMPATIBILITY WITH THIS MODEL 625P DVD PLAYER,
PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.”
VIDEO Plus+ and PlusCode are registered trademarks of Gemstar
Development Corporation. The VIDEO Plus+ system is manufac-
tured under license from Gemstar Development Corporation.
The lighting flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to humans.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the appliance.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems Inc.
IMPORTANT FOR LASER PRODUCTS
1)CLASS 1 LASER PRODUCT
2)
DANGER: Visible and invisible laser radiation when open and
interlock failed or defeated. Avoid direct exposure to beam.
3)
CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to qualified
service personnel.
CAUTION!
•
CD-R/RW discs recorded using a personal computer or a CD
Recorder may not play if the disc is damaged or dirty, or if there
is dirt or condensation on the player’s lens.
• Unfinalized CD-R/RW discs can be played, but not all time
information (playing time, etc.) will be displayed.
• Check the copyright laws in your country before recording from
DVD VIDEO, SVCD, Video CD, Audio CD, MP3 and JPEG discs.
Recording of copyrighted material may infringe copyright laws.
Legal Notices Regarding
Macrovision’s Property Rights
“U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093;
and 6,516,132.”
“ This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights.
Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited. “
This unit complies with the European Directives 89/336/EEC and
73/23/EEC.
The apparatus shall not be exposed to dripping or splashing.
No objects filled with liquids, such as vases, shall be placed on
the apparatus.
4
Playable Disc types
Audio System
Dolby Digital Linear PCM
DTS (Digital Theater Systems)
Video System ( PAL )
This DVD recorder accepts PAL system.
Aspect Ratio
4:3 (Letter Box) Standard
4:3 Pan & Scan
16:9 (Wide-Screen)
Others
Audio : Appears at the beginning of a scene recorded
with multiple audio languages.
Subtitle : Appears at the beginning of a scene recorded
with multiple subtitle languages.
Angle : Appears at the beginning of a scene recorded
from multiple angles.
Note:
The DVD-Video/DVD+RW/DVD+R/DVD-R/DVD-RW Logos
are trademarks of the respective companies.
For best results, use discs with the above logos. The unit
may not playback other discs correctly. Do not use irregular-
shaped discs (e.g. heart-shaped), as these can damage the unit.
It may not be possible to play CD-R, CD-RW, DVD-R, DVD-
RW, DVD+R, DVD+RW in all cases due to the type of disc or
condition of the recording.
Unplayable disc types
The unit does not play back disc type listed below. If you
try to play back these discs, excessive noise may cause
damage to your speakers.
1) Unfinalized discs from other DVD/CD recorders.
2) DVD AUDIO, PHOTO CD, SACD, HDCD
(When placing an unplayable disc on the disc tray, the DVD
recorder will display “Unknown Disc” on the display panel after
attempts of trying to loading the disc fail.)
Region code of DVD-Video
This unit can play back DVD-VIDEO discs compatible with
the region code printed on the rear of the unit.
Example of playable DVD-VIDEO discs:
If you try to play any other discs, the message “Invalid
Region Code” will apear on TV screen.s:
Recordable Disc types
Disc Types Logos Characteristics
DVD-VIDEO
This unit can playback DVD-Video discs and the
region code is printed on the rear of the unit.
DVDЀR/ЀRW
DVDЁR/ЁRW
DVDЁR, DVDЁRW and DVDЀR, DVDЀRW, discs
written in the DVD-Video format and finalized.
Video CD (VCD)
Super Video CD (SVCD)
Video with CD sound, VHS quality, MPEG-1 &
MPEG-2 compression technology.
Audio CD
CD is recorded as a Digital Signal with better audio
quality, less distortion and less deterioration of audio
quality over time.
CD-R/RW
(JPEG/BMP/MP3)
This unit can play CD-R and CD-RW discs recorded
with Audio CD or Video CD format, or with
JPEG/BMP/MP3 files. Close the sessions or finalize
the disc after recording.
Disc Types Logos Characteristics
DVDЀR/ЀRW
DVDЀR disc written in the DVDЀVR format.
DVDЀRW disc written in the DVDЀVR format.
CDЁR/ЁRW
CDЁR/CDЁRW disc written in the MPEG1 or
MPEG2 video format or written in PCM Audio mode.
DISC INFORMATION
5
Remote Control
To install batteries
Open the battery compartment and
insert the batteries. Make sure the
polarities (+ and -) match the marks
indicated inside the remote control.
Do not use rechargeable type
batteries.
Remote sensor
The remote has a range of
approximately 7M and works
best when pointed directly at
the unit horizontally at angles
up to 30° from the front of the
unit.
CON TROLS AN D DISPLAYS
The Remote Control
1) Timer button (TIMER)
2) Open / Close button (
OPEN / CLOSE)
3) VIDEO Plus+ button (VIDEO Plus+)
4) Stop button (
STOP)
Play button (
PLAY)
Pause / Step button (
PAUSE / STEP)
5) REV/ FF buttons (
REV / FF)
Skip buttons (
PREV / NEXT)
6) Display button (DISPLAY)
7) Disc Menu button (DISC MENU)
8) Edit button (EDIT)
9) Cursor (), Enter buttons (ENTER)
10) Copy button (COPY)
11) Number buttons (1~9,0)
12) Easy Guider Menu button (GUIDER)
Browser button (BROWSER)
Disc Tools button (TOOLS)
Navigation button (NAVI)
13) Audio button (AUDIO)
Angle button (ANGLE)
Zoom button (ZOOM)
Subtitle button (SUBTITLE)
14) Source button (SOURCE)
15) Power button (
STANDBY/ON)
16) HDD/DVD button (HDD/DVD)
17) Record button (
REC)
18) Play List Menu button (PLAY LIST MENU)
19) Record Mode button (REC MODE)
20) Time shift button (TIME SHIFT)
21) CH Up / Down buttons (CH+ / CH-)
22) Setup button (SETUP)
Do not dispose of the batteries in your domestic or any
other waste bin! Instead, bring them to the nearest
collection site, e.g. at your retail dealer or supermarket:
you will find special collection boxes there for used
batteries. All collected batteries will be recycled.
Please help to conserve our environment. Thank you.
6
Front panel connections
Display window
Names of parts and controls
1) POWER ON/OFF Button ( /ON)
Turns the recorder on and off.
2) DISC TRAY
Holds discs securely during recording or playback.
3) RECORD Button (
REC)
Starts recording.
4) DVD Indicator
Lights up when DVD is set as the playback/record
device.
5) HDD Indicator
Lights up when HDD is set as the playback/record
device.
6) SOURCE Button (SOURCE)
Selects equipment connected to the line inputs.
7) DISPLAY Window
Operation indicators are displayed here.
8) DV IN Jack
Connects digital video camcorders to this DVD Recorder.
9) OPEN/CLOSE Button (
OPEN / CLOSE)
Opens or closes the disc tray.
10) PLAY Button (
PLAY)
Plays a disc.
11) STOP Button (
STOP)
Stops playing or recording a disc.
12) HDD/DVD Button ( HDD/DVD )
Press to switch between HDD and DVD.
13) VIDEO IN/AUDIO IN L/R Jacks
Connect the output of external equipment.
CON TROLS AN D DISPLAYS
1) Play indicator
2) DVD indicator
3) SVCD indicator
4) VCD indicator
5) CDDA indicator
6) FILE indicator
7) CD indicator
8) DVD+R indicator
9) Pause indicator
10) Record indicator
11) Timer record mode
12) Multi-information window
13) DVD+RW indicator
14) CD-R/DVD-R indicator
15) CD-RW/DVD-RW indicator
7
CON TROLS AN D DISPLAYS
Rear panel connections
Names of parts
1) TUNER(RF OUT/RF IN) Jacks
Antenna cables input and output.
Note: DVD signals don’t go through here. Make
proper connections before use.
2) SCART IN Jack
Composite/RGB signal input.
3) SCART OUT Jack
Composite/RGB/S-Video signal output.
4) AV OUTPUT Jacks
Composite signal output.
5) COMP OUT Jacks
Component signal output.
6) DIGITAL OUT (COAXIAL) Jack
Connect to an amplifier or a receiver having a
digital input jack.
7) DIGITAL OUT (OPTICAL) Jack
Connect to an amplifier or a receiver having a
digital input jack.
8) AC IN Terminal
Connect the power cord.
8
CONNECTIONS
Before making connections
1) Do not plug the AC power cord into the outlet until all other connections are made.
2) Connect VIDEO OUT of the unit directly to the video input of your TV. Connecting VIDEO OUT of the unit to a TV via a VCR may
cause a viewing problem when playing back a copy-protected disc. You may also have a viewing problem when connecting
the unit to an integrated TV/Video system.
Connecting to the antenna outlet and the television
Before using the unit, follow the steps below to connect the unit to the antenna cable and TV.
Connecting to a TV with SCART jack
Use the antenna cable (supplied) to connect the RF IN on the unit to the antenna outlet.
Use the antenna cable (not supplied) to connect the RF OUT on the unit to the RF input on the television.
Use a SCART cable to connect the SCART OUT jack on the unit to the SCART IN jack on the television.
Notes:
1. Do not place this unit on top of other equipment that may generate heat. Excessive heat may cause this unit to
malfunction.
2. For Digital Cable and Satellite TV users please connect your decoder’s output to this unit’s input.
9
FOR BETTER VIDEO QUALITY
If your TV has Component Video inputs, you can enjoy superior picture quality.
Connecting to a TV via COMPO OUT
Connecting to a TV with component jacks
Use COMPONENT cable (not supplied) to connect the COMPO OUT on the unit to the COMPONENT input on the television.
Notes:
1. Enter system setup to enable COMPO OUT (refer to the section titled “Quick Setup”).
2. When using COMPO OUT connections, please remove all other video output connections.
3. In this configuration, the Red and White audio connections are required.
10
Connecting to a stereo audio amplifier or receiver
Use an audio cable to connect the L/R AV OUTPUT on the unit to
the audio inputs on a stereo amplifier or a receiver.
There are two types of audio connections, analog and digital.
Connecting to a digital audio device
Connect an amplifier with Dolby Digital and DTS decoders to enjoy surround sound.
Digital out optical
Use an optical digital cable (not supplied) to connect
the DIGITAL OUT OPTICAL (digital optical output) on
the unit to the digital optical input on an stereo amplifier
or a receiver.
Digital out coaxial
Use a coaxial digital cable (not supplied) to connect the
DIGITAL OUT COAXIAL (coaxial digital output) on the unit
to the coaxial digital input on an stereo amplifier or a
receiver.
FOR BETTER A UDIO QUALITY
11
Remote Control & Setup menu
Follow the steps below to reset personal preferences for using
the DVD recorder. Confirm that all connections are secured
properly.
1. Press [
STANDBY/ON] to turn on the unit.
2. Press [SETUP] to display the system menu.
3. Press [] [] to select “System,” “Language,”
“Playback,” “Record,” “Audio,” “TV Tuner” or “Exit”
and press [ ] or [ ] to move to the next or
previous menu.
4. Press [ ][ ] to select the item you want to
change.
(Refer to the “GUI operation” section for detailed menu)
5. Press [ENTER] to confirm the setting.
6. Press [SETUP] to exit the setup menu or press []
to return to the previous menu.ot
Notes:
1. To record TV programs using the Timer Record feature,
you must set the time accurately.
2. Please see also “ GUI(Graphical User Interface) Operation“
on page 42/43 for further information.
Setting the date and time
Check that the clock is correctly set before initiating the timer
recording function. If the clock is set incorrectly, Timer Record
results may not be accurate.
Set the date
1. Press [SETUP] and the setup menu will
be displayed.
2. Select “System” using [] or [] and press [ENTER].
3. Select “Date” using [] or [] and press [ENTER].
4. Change the day/month/year in the highlighted field using []
or [] or the numbered buttons (0~9) on your remote
control and confirm by pressing [ENTER].
5. When all settings are correct, press [] to return to the
main menu.
6. To exit the setup menu, press [SETUP].
Set the time
1. Press [SETUP]. The setup menu will appear.
2. Select “System” using [] or [] and press [ENTER].
3. Select “Time” using [] or [] and press [ENTER].
4. Change the “hour/minute/second” in the highlighted field
using [] or [] or the numbered buttons (0~9) on your
remote control.
5. When all settings are correct, press [] until returning to
the main menu.
6. To exit the setup menu, press [SETUP].
Notes:
Setting Audio
Press [SETUP] and select “Audio.”
Digital Output
PCM Bit Stream
(Enable digital audio output with PCM or encoded data)
DTS Out
On / Off
Surround
Stereo DOLBY DTS
TV sound Bilingual
Main Sub
MPEG
PCM Bit Stream
SETUP MENU
Note:
If you accidentally set “Progressive” as the Video Output
when not connecting to a progressive scan-compatible TV,
you may lose the video signal on your TV instantly. To get the
picture back, press [(Cursor Right)] and the numbered
buttons “5,” “0,” “2” and “0” on the remote control and then
[ENTER]. In about 8 seconds, you can re-set the video output.
Setting video output
1. Press [SETUP] and the setup menu will be displayed.
2. Select “System” using [] or [] and press [ENTER].
3. Select “Video Output” as “Scart S-Video,” “Scart RGB”
“Component” or “Progressive” using [] or [] and press
[ENTER]. (Refer to “ GUI operation” section for details)
4. When all settings are correct, press [] to return to the
main menu.
5. To exit the setup menu, press [SETUP].
Progressive Scan mode
You can change the video output mode when you press
[SETUP] and select “System-->Video Output-->
Progressive.”
Video output mode:
576i: Interlace video 576p: Progressive video
You must connect the component output on the unit to a
576p compatible television.
Setting Aspect ratio
Press [SETUP] and select “Playback”-->”Aspect Ratio.”
Select “4:3” (regular) or “16:9” (widescreen) to suit your
television. If you have a regular 4:3 television, you can also
select how video title on some discs is presented.
4:3 L.Box (4:3 Letter Box)
Select when you connect the unit to a
normal (4:3) TV.
When playing back a DVD-VIDEO disc
recorded in wide picture format, the picture
is shown with black bars at the top and bottom.
4:3 Pan (4:3 Pan & Scan)
Select when you connect the unit to a
normal (4:3) TV.
When playing back a DVD-VIDEO disc
recorded in wide picture format, the picture
is zoomed to fill the screen vertically, and
the left and right sides of the image are chopped off. Note,
however, that the picture will be shown in the 4:3 L.Box (4:
3 Letter Box) mode even if you select the 4:3 Pan (4:3 Pan &
Scan) mode depending on the disc.
16:9 Wide (16:9 Wide Screen)
Select when you connect the unit to
a wide-screen (16:9) TV.
Note:
When stereo broadcasting is received, L, R or MONO cannot
be selected for output audio.
12
TV CHANNEL SETUP
9. The channel scanning starts. This process may
take a few minutes.
10.When all the TV channels have been searched
and stored, press [SETUP] to exit.
Notes:
1. If the available channel number in your residence area
exceeds the maximum receivable channel numbers of this
DVD Recorder, the scan will be discontinued. The maxi
mum receivable channel numbers are:
Antenna: 168 (chs)
Cable: 104 (chs)
Auto: 176 (chs)
2. It would take more time for auto channel scanning
depending on the receiving condition of your antenna.
Fine-tuning TV channels manually
After you have performed the channel scanning, you may like
to fine-tune the TV channel signal manually. Follow the steps
below to complete fine tune.
1. Press [SETUP] to display the “Setup”, press
[] or [] to select the “TV Tuner” icon and
press [].
2. Press [] or [] to select “Fine Tune” and
press [].
3. Press [] or [] to fine-tune the channel signal.
4. When complete, press [SETUP] to exit the
setup menu.
Editing TV channels manually
After you have performed channel scanning, you may like to
further edit the TV channels. This function allows manually
adding/deleting channels, swapping channel order, inserting
a channel to a specific order, renaming the channels and so
on.
1. Press [SETUP] to display the “Setup”, press
[] or [] to select the “TV Tuner” icon and
press [].
2. Press [] or [] to select “Utilities” and press
[].
3. Press [] or [] to select “Edit Channel” and
press [ENTER]. The CHANNEL EDITOR menu will be
displayed.
For detailed operation instructions on the “Channel Editor”
menu, refer to the “CHANNEL EDITOR” section.
TV channel scanning
When the “Scan Channel” function is activated, the TV
channels are searched and stored in a specific order. If the
channel assignment of your TV content provider is changed
or if you are reinstalling this DVD recorder, you may need to
start this procedure again.This will replace the TV channel
stored with the new ones.
Before scanning channel, set the “TV Signal” and “Country”
for initiation.
1. Ensure the antennas are securely connected to
the DVD recorder.
2. Switch on the TV set and the DVD recorder.
3. Press [SETUP] to display the setup menu, press
[] or [] to select the “TV Tuner” icon and
press [].
4. Press [] / [] to select “TV Signal” and press
[ ].
5. Press [] / [] to select “Cable,” “Antenna” or
“Auto” depending on how you receive your
terrestrial TV channels and press [ENTER]. Press
[ ] to return to the previous menu and save the
setting.
If you select “Auto,” the unit will automatically scan both
channels available at cable and antenna connections, which
might take longer than needed.
6. Press [] / [] to select “Country” and press
[]. Press [] / [] and [ENTER] to select the
country of your residence from the list . Press []
to return to the previous menu and save the
setting.
7. Press [] / [] to select “Utilities” and press [].
8. Press [] / [] to select “Scan Channel” and
press [ENTER] to start channel scanning.
If you wish to stop scanning, move to “Stop Scan” and press
[ENTER]. The scanning process will be discontinued.
13
CHANN EL EDITOR
Moving up or moving down the TV channel
1. Press [] [] to select one of the TV channels
and press [].
2. Press [] [] to select “Move Up” or “Move
Down” and press [ENTER].
The order of the TV channel will be changed.
Each time you press [] or [] and the item changes as
follows:
3. To move the location of other TV channels, repeat
step 1~2 to complete the settings.
4. Press [] [][] [] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNEL EDITOR” menu.
To access to the Channel Editor menu, press [SETUP], select
“TV Tuner,” “Utilities,” “Edit Channel” and press [ENTER]. Or,
press [SOURCE] to set “TV” as the input signal source and
press [EDIT]. Either way, the Channel Editor menu will be
displayed.
Swapping TV channels
This function allows you to manually swap the TV channel
order stored in the unit to match the TV channel order stored
in your TV set.
1. Press [] [] to select a TV Channel and press
[].
2. Press [] [] to select “Swap With” and press
[ENTER].
3. Press [] [][] [] to enter the “Channel
number,” and press [ENTER] to swap. The order
of the channels will be swapped with the channel
number entered.
4. To swap other TV channels, repeat step 1~3 to
complete the settings.
5. Press [] [][] [] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNEL EDITOR” menu.
Renaming TV channels
1. Press [] / [] to select a TV channel and press
[ ].
2. Press [] [] to select “Rename” and press
[ENTER].
The display for
entering a title name
appears.
3. Select the desired
characters from the
keypad. Press
[ENTER] after each
entry.
4. When you finish
entering the title name, press [] [] [] [] to
select “Finish” and press [ENTER].
Notes:
1. You can only enter up to 10 characters for a name.
2. If you wish to enter “space”, select a blank on the keypad
and press [ENTER].
Inserting TV channels
1. Press [] [] to select a TV channels and
press [].
2. Press [] [] to select “Insert To” and press
[ENTER].
3. Press [] [][] [] to enter the “Channel
number,” and press [ENTER]. The channel will be
moved to the desired location.
4. To change the locations of other TV channels,
repeat step 1~3 to complete the settings.
5. Press [] [ ][] [] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNEL EDITOR” menu.
14
Thanks to this programming system, you no longer need to
tediously enter the date, programme number, start and end
times. All the information needed by the DVD recorder for
programming is contained in the VIDEO Plus+
®
programming
number. This 9-digit PlusCode number is found in most TV
listings magazines.
Before setting up, confirm that the all cables are securely
connected.
Setting up VIDEO Plus+
®
systemCHANN EL EDITOR
Turning on or turning off TV channels manually
After you have performed the channel scanning process, you
may like to add or delete some of the TV channels. This function
allows turning on the channel not found at channel scanning or
turning off the channel found manually.
1. Press [] [] to select a TV Channel not found at
channel scanning and press [].
2. Press [] [] to select “Turn On” and press
[ENTER]. The TV channel selected will be turned
on.
To turn off the TV channel, move to “Turn Off” and press
[ENTER]. The TV channel selected will be turned off.
3. To turn on other TV channels, repeat step 1~2 to
complete the settings.
4. Press [] [][] [] to select “Exit,” press
[ENTER] to save the setting and exit the
“CHANNEL EDITOR” menu.
SettinguptheVIDEOPlus+
®
system
1. Press [SOURCE] to set TV as the input signal
source.
2. Press [EDIT] to display the “CHANNEL EDITOR”
menu.
3. Press [] [] to go to a channel and press
[ENTER].
4. Press [] [] [] [] to go to “GCN” and press
[ENTER].
The menu to enter GCN is displayed.
5. Use the numbered buttons (1~9) to enter the
GCN and press [ENTER] when done.
Press [] [] to go back to advance/return to the previous/
next digit.
6. To set GCN for other channels, repeat step 3~5.
7. When complete, press [] / [] to go to “Exit”
and press [ENTER] to exit the channel editor
menu.
PDC
“PDC” (program delivery control) are used to control
the start and duration of TV channel recordings. If a TV
program starts earlier or ends later than was
scheduled, the DVD recorder will then turn on and off
at the correct time. Refer to “Timer Record using the
VIDEO Plus+ system” section for details about setting.
Notes:
1. You must enter the start time exactly to the minute. If you
want to program a time that is different from the PDC time,
you must switch off PDC.
2. Only on TV program of a TV channel can be controlled
using “PDC” at a time. If you want to record two or more
TV programs on a TV channel using “PDC,” you need to
program these as two separate recordings.
3. Since the DVD recorder requires a certain lead time for
getting the disc up to speed and positioning the laser before
recording can start, it is possible that the recorder will miss
the first few seconds of a TV show recorded with PDC. In
this case, disable PDC and enter a start time one minute
earlier.
15
EAS Y GUI DER
Playback video files
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Playback” and then
press [ENTER].
3. Press [] [] to select DVD or HDD and then
press [ENTER].
4. Press [] [] to select “Video” and press
[ENTER].
5. The selected file screen appears. Press [] []
[] [] to select a video file to start playback
with and press [ENTER].
If you want to go to the next page or return to the previous
page, you can select the [
] [ ] icon or the page
number icon.
Playback music files
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Playback” and then
press [ENTER].
3. Press [] [] to select DVD or HDD and then
press [ENTER].
4. Press [] [] to select “Music” and press
[ENTER].
5. The selected file screen appears. Press [] []
[ ] [] to select a music file to start playback
with and press [ENTER].
If you want to go to the next page or to the return previous
page, you can select the [
] [ ] icon or the page
number icon.
6. Press [PAUSE/STEP] to pause playback.
Press [
PLAY] to resume normal playback.
Press [
STOP] to stop playback at a marked stop.
Press [ STOP] twice to bring the playback to a full stop.
Playback picture files
1. Press [ GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Playback” and then
press [ENTER].
3. Press [] [] to select DVD or HDD and then
press [ENTER].
4. Press [] [] to select “Pictures” and press
[ENTER].
5. The selected file screen appears. Press [] []
[ ] [] to select a picture file to start playback
with and press [ENTER].
If you want to go to the next page or return to the previous
page, you can select the [
] [ ] icon or the page
number icon.
6. Press [PAUSE/STEP] to pause playback.
Press [
PLAY] to resume normal playback.
Press [
STOP] to stop playback.
Easy Guider menu is an unique user interface to
guide you through basic functions of this
recorder. By using the Easy Guider menu, it is
less time-consuming to operate this system.
Users no longer need to go through normal
operations that may require far more steps and
different interfaces.
6. Press [ PAUSE/STEP] to pause playback.
Press [
PLAY] to resume normal playback.
Press [
STOP] to stop playback at a marked stop.
Press [ STOP] twice to bring the playback to a full stop.
16
Playback pictures with music
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Playback” and then
press [ENTER].
3. Press [] [] to select DVD or HDD and then
press [ENTER].
4. Press [] [] to select “Pictures With Music”
and press [ENTER].
5.
The selected file screen appears.Press [
] []
[] [] to select a picture file to start playback
with and press [ENTER].
6. Press [] [][] [] to select a music file to
start playback with and press [ENTER].
Playback will start.
7. Press []/[] to select “Rotate RIGHT” or “Rotate
LEFT” and “Rotate UP” “Rotate down.”
Press [] or [] to skip the picture.
Press [
NEXT ] or [ PREV ] to skip the
MP3 file.
8. Press [
PAUSE/STEP] to pause playback.
Press [
PLAY] to resume normal playback.
Press [
STOP] to stop playback.
EAS Y GUI DER
Playback the last recorded title (on HDD only)
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Playback” and then
press [ENTER].
3. Press [] [] to select HDD and press [ENTER].
4. Press [] [] to select “Last Record” and press
[ENTER].
Playback of the title last recorded on your HDD will begin.
5. Press [ PAUSE/STEP] to pause playback.
Press [
PLAY] to resume normal playback.
Press [
STOP] to stop playback at a marked stop.
Press [ STOP] twice to bring the playback to a full stop.
Record on the HDD
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Record” and then
press [ENTER].
3. Press [] [] to select the Signal- Input ( TV,
AV1-front, AV2-rear, DV-in) and press [ENTER].
If you select “TV,” press [] [] to select the channel you want
to record and press [ENTER]. Press [] [] and [ENTER] to set
the PDC mode off.
4. Press [] [] to select “HDD” and press
[ENTER].
5. Press [] [] to select “Recording mode” and
then press [ENTER].
If you select “TV” in step 3, press [] [] to select the desired
TV sound and press [ENTER].
6. Press [ENTER] to start recording.
Press [
STOP] to stop recording.
Press [
PAUSE/STEP] to pause recording.
Notes:
1. You can press [GUIDER] to exit the Easy Guider menu.
2. Bilingual TV program which input through AV input terminal
is recorded on DVD disc (HDD) as stereo TV program.
When this title is playbacked, the both Main and Sub sound
can be heard from the speakers.
Please choose the desired sound which you want to enjoy
on the TV side.
3. Stereo broadcasting is recorded by stereo and monaural
one is recorded by mono.
17
EAS Y GUI DER
Record on DVD
Make sure a recordable disc is inserted before recording.
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Record” and then
press [ENTER].
3. Press [] [] to select the Signal-Input (TV,
AV1-front, AV2-rear, DV-in) and press [ENTER].
If you select “TV,” press [] [] to select the channel you want to
record and press [ENTER].
4. Press [] [] to select “DVD” and press
[ENTER].
5. Press [] [] to select a disc format and press
[ENTER].
If you select “TV” in step 3, press [] [] to select the desired
TV sound and press [ENTER].
“Go !” is selected.
6. Press [ENTER] to start recording.
Press [
STOP] to stop recording.
Press [
PAUSE/STEP] to pause recording.
Notes:
1. If a new recordable CD-R or a newly erased CD-RW is
used for recording, press [ ] [] [] [] to select a
disc format the disc is to be prepared as and press
[ENTER] : SVCD, VCD, Audio CD or Data CD.
2. Stereo broadcasting is recorded by stereo and monaural
one is recorded by mono.
Timer Record (Date/Time Setting)
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Timer Record” and
then press [ENTER].
3. Press [][] to select “Date/Time Setting” and
press [ENTER].
4. Press [] [] to select the Signal-Input ( TV,
AV1-front, AV2-rear, DV-in ) and press [ENTER].
If you select “TV,” press [] [] to select the channel you want to
record and press [ENTER]. Press [] [] and [ENTER] to set the
PDC mode on or off.
If you select “AV1-front or AV2-rear,” press [] [] to set PDC
mode on or off.
5. Press [][] to select “Once,” “Daily,” or “Weekly.”
18
EAS Y GUI DER
Note:
For Timer Record, there are six recording modes avaialbe: HQ,
SP, LP, EP, SLP and Just Fit. When the recording mode is set
to be “Just Fit,” the recording mode will be automatically
adjusted depending on how much recording space is available
on the disc/HDD.
Timer Record (VIDEO Plus+
®
Setting)
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Timer Record” and
then press [ENTER].
3. Press [] [] to select “VIDEO Plus+” and press
[ENTER].
4. Press [] [] to select once, daily or weekly
and press [ENTER].
5. Use the numbered buttons to enter the PlusCode
number and then press [ENTER] . Press [][] to
set the PDC mode on or off and press [ENTER].
6. Press [][] [] [] or the numbered buttons
(0~9) to set the date and press [ENTER] when done.
7. Press [][] [] [] or the numbered buttons
(0~9) to set the time and press [ENTER] when
done.
8. Press [][] to set “Length” and then press [ENTER] .
9. Press [][] to select “HDD” or “DVD” and then
press [ENTER] .
10. Press [][] to select a disc format and press
[ENTER]. (For DVD disc only)
11. Press [] [] to select a recording mode and
press [ENTER].
12. Press [] [] to select the desired TV sound and
press [ENTER].
13. The “Timer Record information” will appear and
press [ENTER] to
exit the timer record settings.
13. Press [
STANDBY/ON] to turn the recorder
off to activate Timer Record function.
Note:
When you first play a recordable CD-R disc or an empty CD-RW
disc on the disc tray, select a disc format the disc is to be
prepared as: SVCD, VCD, Audio CD or Data CD. The format
selected determines the recording quality.
19
EAS Y GUI DER
Copy (From DVD to HDD )
Press [ OPEN/CLOSE] to open the disc tray and insert a
disc with recorded contents on it. Press the button again to
close the tray.
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [] to select “Copy” and press
[ENTER].
3. Press [] [] to select “DVD to HDD” and
press [ENTER].
4. Press [] [] to select the type of the file: Video,
Music, Pictures or All and press [ENTER].
5. Press [] [][] [] to select the file to copy and
press [ENTER].
6. When complete, go to “Exit” and press [ENTER].
Notes:
1. You can only copy picture files (in JPEG or BMP formats),
audio files (in MP3 or WAV format). Sanyo has no right to
grant such permission. Permission should always be
sought from the copyright owner.
2. The title of DVD-Video cannot be copied from DVD to
HDD.
6. After entering the PlusCode number, the “GCN”
and “Present Channel” will be displayed.
Press [ENTER] to preset the channel.
7. Press [][] to select “DVD” or “HDD” and then
press [ENTER] .
8. Press [] [] to select a disc format and then
press [ENTER].
If a CD-R or CD-RW is used for recording, you need to select
SVCD, VCD or Audio CD. If a DVD disc is used for recording,
you need to select “DVD VR” format.
9. Press [] [] to select “Recording mode” and
then press [ENTER].
For CD-R/RW, the format selected determines the recording
quality.
10.Press [] [] to select TV audio and press
[ENTER].
11.The “Timer Record information” will be displayed.
Press [ENTER] to exit the timer record settings for
VIDEO Plus+
®
.
12.
Press [ STANDBY/ON] to turn the recorder off
to activate Timer Record function.
Note:
When you first play a recordable CD-R disc or an empty CD-RW
disc on the disc tray, select a disc format the disc is to be
prepared as: SVCD, VCD, Audio CD or Data CD. The format
selected determines the recording quality.
3. Press [] [] to select “HDD to DVD” and
press [ENTER].
The disc preparation process will take place in the background.
This process only takes a few moments.
4. Press [] [] to select the type of the file: Video,
Pictures or Music and press [ENTER].
5. The selected file screen appears. Press [] []
[] [] to select the file to copy and press
[ENTER].
6. When complete, go to “Exit” and press [ENTER].
Copy (From HDD to DVD)
Press [ OPEN/CLOSE] to open the disc tray and insert a
recordable DVD disc. Press the button again to close the tray.
1. Press [GUIDER] to display the Easy Guider
menu.
2. Press [] [ ] to select “Copy” and press
[ENTER].
Note:
You can only copy picture files (in JPEG or BMP formats), audio
files (in MP3 or WAV format) and recorded video titles.
Reference the “Copy” section for the right disc to use.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
