Cumberland v-max is an environmental controller that can be used to monitor and control a variety of environmental parameters, including temperature, humidity, and light. It can be used in a variety of applications, including greenhouses, poultry houses, and industrial facilities. The v-max has a number of features that make it a versatile and easy-to-use controller. These features include:
- A large, easy-to-read display that shows all of the important information at a glance.
- A simple, user-friendly interface that makes it easy to set up and operate the controller.
- A variety of input and output options that allow the v-max to be connected to a wide range of sensors and devices.
Cumberland v-max is an environmental controller that can be used to monitor and control a variety of environmental parameters, including temperature, humidity, and light. It can be used in a variety of applications, including greenhouses, poultry houses, and industrial facilities. The v-max has a number of features that make it a versatile and easy-to-use controller. These features include:
- A large, easy-to-read display that shows all of the important information at a glance.
- A simple, user-friendly interface that makes it easy to set up and operate the controller.
- A variety of input and output options that allow the v-max to be connected to a wide range of sensors and devices.
FEGHI JKLMNOPQRS
n.u. n.u. n.u.
TUV
L1
GND
L2/N
L1
115V
L2/N
NOCNC
CNO
5678910 11 12 13 14 15 16 17 18 19 20 21 22
0-10V 0-10V
4-20mA
GND GNDGNDVDC VDC VDCCOM
GNDOUT PWR
Power
ABCD
[21] →
[20] →
[19] →
[Q] →
[R] →
[S] →
[R] →
[C] →
[D] →
[C] →
← [1]
T°
T°
T°
T°
T°
T°
T°
T°
T°
NH3
← [3]
← [2]
ABGND ABGND
ABGND
ABGND
1234
V-MAX
1234
A
Please scan the QR Code to access the complete manual or
visit the website.
Cumberland: http://www.cumberlandpoultry.com
GSI Electronics Inc. • 5200 Armand Frappier Saint-Hubert, Qc
Canada J3Z 1G5 • Phone: 1-877-926-2777
E-mail: [email protected]
WIRING DIAGRAM
V-MAX
#891-00488 REV 05
REV 09
EN
Page 1
Cumberland
Digital input 1
(water meter, feeder or auger)
Digital input 2
(water meter, feeder or auger)
Digital input 3
(water meter, feeder or auger)
Digital input 4
(water meter, feeder or auger)
Digital input 5
(water meter, feeder or auger)
Digital input 7
(water meter, feeder or auger)
Digital input 6
(water meter, feeder or auger)
Digital input 8
(water meter, feeder or auger)
USB Connector
(for memory card)
> Module
Connections:
See Overleaf
Dwyer gauge static
pressure probe (opt.)
0-10V Load 1 (opt.) 0-10V Load 2 (opt.)Relative
humidity sensor
HS-1 (Optional)
115/230 Vac
Voltage Selector 6
Controller
Power Supply
115/230Vac
Alarm
Supply
Inside T°
probe 2
Inside T°
probe 1
Inside T°
probe 3
Inside T°
probe 4
Inside T°
probe 5 (opt.)
Inside T°
probe 6 (opt.)
Inside T°
probe 7 (opt.)
Inside T°
probe 8 (opt.)
Outside T
probe (opt.)
Ammonia
probe (opt.)
1. Mounting Instructions: Leave a
clearance of at least 16ʺ (400 mm) to the left of the
controller box to allow the cover to be removed
for maintenance.
2. Cable Entry: Punch holes at the bottom of
the enclosure to allow wires to be introduced in
the controller. Do not drill the top or side panels
of the enclosure.
3. Alarm System: Installation of a good quality
alarm system is strongly suggested to warn of
power failures and high/low temperatures.
4. Surge Protection: Provide a surge
protection (including lightning protection) from
the power supply to the controller and from
the control to the probes. Consult a certied
electrician if required.
5. Low Voltage Wires: Install low voltage
cables at least 12 inches (300 mm) away from
high voltage cables (120, 230 or 380 Vac or
24 Vdc). Always use twisted shielded cables
to wire low voltage devices and always cross
high and low voltage cables at a 90° angle.
This applies to:
- Sensor cables
- Potentiometer cables
- Communication cables
- Computer link cables
- 0-10V loads
- All other low voltage devices.
6. Voltage Selection: Set the voltage selector
to the proper position : 115 or 230Vac.
7. Water Meter: The water meter output
should be a dry contact and should not pulse
faster than 60 times a second (60Hz). A 22/12
AWG gauge cable no longer than 2000 feet
(0.6 km) can be used to connect the water
meter. Do not use a cable longer than 2000 feet
even if a larger cable is used. Do not run the
meter cable outside the building!
8. SureLink-2 Module: Refer to the user’s
manual of the SureLink-2 module to set the “End
of line (EOL)” selectors properly.
9. Digital Inputs: The function of each digital
input must be dened in the “Digital Input” tab of
the controller.
INSTALLATION NOTES
SureLink-2 module 9
A-BOX (opt.)
Relative
humidity probe
HP1, HS-100
(Old model)
V-MAX
#891-00488 REV 05
12G12G
ON
OFF
12 345678
ON
OFF
12 345678
ON
OFF
12 345678
L1 L2
12G
LED
LED
LED +IN1 –+IN2 –
+IN3 –+ –IN4
1234
ABCD
com 1
com 2
GND
[A] (Mod.1) →
[B] (Mod.2) →
[D] (GND) →
END OF LINE
YESNO
END OF LINE
YESNO
END OF LINE
YESNO
WIRING DIAGRAM EN
Page 2
V-MAX
(Inside the Enclosure)
Setting the ID Numbers of the
Communication Boards
Each group of 8 relay inside the Output Panel CS
is associated to a communication board behind the
front panel. A unique ID number must be given to
each communication board in use. The table below
gives the ID numbers for each of those boards.
Comm.
Board# Relays# ID
Number
1 Relays 1-8 ID# 1
2 Relays 9-16 ID# 2
3 Relays 17-24 ID# 3
4 Relays 25-32 ID# 4
5 Relays 33-40 ID# 5
6 Relays 41-48 ID# 6
7 Relays 49-56 ID# 7
8 Relays 57-64 ID# 8
9 Relays 65-72 ID# 9
10 Relays 73-80 ID# 10
To assign an ID number to a communication board,
use the block of switches located on each board. The
table below shows how to set the switches for each ID
number.
to next module
(if applicable)
OUTPUT PANEL CS
Comm. Board 1Comm. Board 2Comm. Board 3
Relays 1-8
Relays 9-16
Relays 17-24
block of
dipswitches
Switch Number
ID
Number 1 2 3 4 5 6 7 8
ID 1
ID 2 ON
ID 3 ON
ID 4 ON ON
ID 5 ON
ID 6 ON ON
ID 7 ON ON
ID 8 ON ON ON
ID 9 ON
ID 10 ON ON
-
1
-
2
Cumberland v-max is an environmental controller that can be used to monitor and control a variety of environmental parameters, including temperature, humidity, and light. It can be used in a variety of applications, including greenhouses, poultry houses, and industrial facilities. The v-max has a number of features that make it a versatile and easy-to-use controller. These features include:
- A large, easy-to-read display that shows all of the important information at a glance.
- A simple, user-friendly interface that makes it easy to set up and operate the controller.
- A variety of input and output options that allow the v-max to be connected to a wide range of sensors and devices.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Cumberland Expert VP-18 Temperature Controller Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Munters CC247 Elite Product information
-
-
-
-
-
Omega CDCN12 and CDCN13 Owner's manual
-
-
-
-