Thinklogical VX40 Matrix Switch Quick start guide

Thinklogical
Brand
Thinklogical
Model
VX40 Matrix Switch
Type
Quick start guide
QUICK-START GUIDE
VX40 Router KVM Matrix Switch Chassis, 6 Rack Units, 400 Watts
Copyright c 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
Single-Head, Single-Link DVI/KVM Source
KVM Matrix Switch
Powered by
MRTS Technology
Single-Head, Single-Link DVI/KVM Destinations
VX40
router
QUICK-START GUIDE
STEP 8: (Final step) Connect both supplied AC Power Cords (PWR-0000006-R)
to the receptacles located on the VX40's power supplies. Plug each one into a
standard AC source. Verify that all system functions are operating properly.
8
L1
L2
VX40_VEL-4_VEL-24_Quick_Start_Rev_C
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
1
2
3
4
5
6
7
8
9
10
POWER SUPPLY 1 (LEFT):
POWER SUPPLY 2 (RIGHT):
FANS:
TEMPERATURE WARNING:
TEMPERATURE SHUTDOWN:
CPU:
INPUT/OUTPUT CARDS:
ANY OF THE ABOVE
COMMON
GROUND
The VX40 Router Critical Hardware Alarms: (Located at the top, left rear of the unit.)
Fan failure, temperature spikes, DC voltage and/or current out of range,AC power input interruption and module removed
Fan failure, temperature spikes, DC voltage and/or current out of range,AC power input interruptionand module removed
Individual fan monitoring
Chassis over temperature, multiple sensors
Chassis over temperature causing shutdown
Card failure (Only with a redundant card)
SFP+ failure, laser output fault
As used with Thinklogical’s™ Velocitykvm-4 and the Velocitykvm-24
Video Extension Systems
100-240v –50/60 Hz 12A
100-240v –50/60 Hz 12A
ALARM
UPSTREAM DOWNSTREAM CONTROLLER
1-5 6-10 26-3011-15 16-20 21-25 31-35 36-40 1-5 6-10 26-3011-15 16-20 21-25 31-35 36-40
5
4
3
2
1
CONSOLE
ACTIVE
RESET
FAULT
L
A
N
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
5
4
3
2
1
CONTROLLER
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER POWER
RS232
CONSOLE
ACTIVE
RESET
FAULT
CONTROLLER
RS232
L
A
N
Thinklogical’s™ VX40 KVM Matrix Switch features redundant
Power Supplies and Controller Modules for uninterrupted
performance, even during system reconfiguration, updates or
debug. The VX40 remains fully functional with only one Power
Supply installed or with one Controller activated.
NOTE: When using a single Controller, the module on the left
(Primary) must be used.*
Primary Controller Card
Optional Secondary Controller Card
*
L2
L1
L3
Video 1 & Data
Downstream
Video 2 Video 2
Data Upstream
Data Upstream
Switch
Fabric
SFP+ A
(Video/data IN,
data OUT)
SFP+ A
(Video/data OUT,
data IN)
SFP+ B
(Video IN) SFP+ B
(Video OUT)
Digital Crosspoint Switch
T
T
T
R
RR
UPSTREAM DOWNSTREAM
Velocity
Tx
DVI/Data
Source
Velocity
Rx
DVI/Data
Destination
Video 1 & Data
Downstream
U
P
D
A
T
E
S
LINE OUT
MIC IN
P
S
2
USB HID
HOST
CNTRL
USB 1.1
SER IAL PORT
DVI OUT 1
DVI OUT 1 DDC
PWR FOL
USB 2.0
VEL-U00M24-STRX
Receiver
Single-Link, DVI 2 Display/KVM
Destinations
2
DVI OUT 1 DDC
DVI OUT 2 DDC
AUDIO
PS/2 or USB connectors
L2L1
L2 L1
STEP 2: Ensure that the VelocityKVM Receiver’s ON/
OFF switch is in the OFF (0) position. Depending on your
configuration, connect your desktop devices (monitors,
keyboard, mouse, etc.) to the Receiver using standard
cables as shown in the example below. Turn all the
devices ON. Insert the AC power cord into the Receiver
and plug it into a standard AC source. Turn the unit ON.
L3
L3
USB
2.0
DVI 1
DVI 2
Audio OUT►
USB 1.1 (Keyboard / Mouse)
VEL-U00M24-STTX
Transmitter
Velocitykvm-24
DEV
LINE IN
MIC OUT HID
P
S
2
LOCAL
FROM CPU
USB HID
HOST
CNTRL
USB 1.1
UPDATES
SER IAL PORT
DVI OUT 1 DVI OUT 2
DVI IN 2
DVI IN 1
L1L2L3
CLINK
PWR
CP FOL
6
STEP 6: Connect your USB, PS/2
and Audio sources to the
VelocityKVM Transmitter’s inputs.
STEP 5: Connect the DVI IN cables from
the CPU to the VelocityKVM Transmitter
and the DVI OUT cable(s) from the
transmitter to the local monitor(s).
L2
STEP 4: Ensure the
VelocityKVM
Transmitter’s ON/OFF
switch is in the OFF (0)
position. Connect the
Power Cord and plug it
into a standard AC source.
Turn the switch ON (1).
Local DVI 1
(optional)
Local DVI 2 (optional)
Optioal local USB or PS/2
Keyboard & Mouse
L1 L3
L1: Video 1 and Data Tx to Rx
L2: Data Rx to Tx
L3: Video 2
PS/2 (Mouse)
PS/2 (Keyboard)
◄Audio IN
Single-Link, DVI 2 Display/KVM Source
DVI OUT 2
DVI OUT 2 DDC
4
3
1
L2
L3 L1
DVI IN
Local DVI Display
(optional)
6
4
5
D
EV
DVI OUT
DVI IN
SER IAL PORT
L1L2
LINE IN
MIC OUT
HID
P
S
2
LOCAL FROM CPU
USB1.1
USB HID
HOST
CNTRL
CAUTION!Replace with same type and rating fuse.
100-240V-,0.5A,50/60 Hz T2A,250VAC
CLINK
PWR
CP FOL
3
UPDATES
Audio OUT►
USB 1.1 (Keyboard / Mouse)
PS/2 (Mouse)
PS/2 (Keyboard)
◄Audio IN
Optional local
USB or PS/2
Keyboard &
Mouse
L2L1
STEP 6: Connect your KMASS devices
from the Source CPU to the appropriate
VelocityKVM Transmitter ports.
STEP 5: Connect the DVI IN cable from
the CPU to the VelocityKVM Transmitter.
Connect the DVI OUT cable from the Transmitter
to the local monitor.
STEP 4: Ensure the VelocityKVM
Transmitter’s ON/OFF switch is in the
OFF (0) position. Connect the AC
Power Cord and plug it into a standard
AC source. Turn the switch ON.
Velocitykvm-4 Transmitter
VEL-U00M04-STTX
100-240V-,0.5A,50/60 Hz T2A,250VAC
CAUTION!Replace with same type and rating fuse.
CNTRL
LINE OUT
MIC IN
HOST
USB HID
U
P
D
A
T
E
S
PWR FOL
USB 2.0
SER IAL PORT
L1
L2
P
S
2
USB1.1
DVIOUT DDC
DVI OUT
DVI OUT
DVI OUT DDC
PS/2 or USB connectors
2
AUDIO
Velocitykvm-4
VEL-U00M04-STRX
Receiver
STEP 2: Ensure that the VelocityKVM Receiver’s ON/OFF switch is in the OFF
(0) position. Depending on your configuration, connect your desktop devices
(monitors, keyboard, mouse, etc.) to the Receiver using standard cables as
shown in the example below. Turn all the devices ON. Insert the AC power
cord into the Receiver and plug it into a standard AC source. Turn the unit ON.
L1L2
L1
L2 1
3
Velocitykvm-24
STEP 3: Connect your VelocityKVM
Transmitter to the VX40 using multi-mode
fiber-optic cables (up to 1000 meters).
Connect L1 to any Upstream Receive Port
and L2 to the same numbered Upstream
Transmit Port. Connect L3 to any other
Upstream Receive Port. (See the Digital
Crosspoint Switch detail diagram, right.)
STEP 1: Connect your
VelocityKVM Receiver
to the VX40 using
multi-mode fiber-optic
cables (up to 1000
meters). Connect L1 to
any Downstream
Transmit Port and L2 to
the same numbered
Downstream Receive
Port as shown. (See
the Digital Crosspoint
Switch detail diagram,
below.)
STEP 1: Connect your VelocityKVM Receiver to the VX40 using
multi-mode fiber-optic cables (up to 1000 meters). Connect L1 to any
Downstream Transmit Port and L2 to the same numbered
Downstream Receive Port. Connect L3 to any other Downstream
Transmit port. (See the Digital Crosspoint Switch detail diagram, left.)
STEP 3: Connect your
VelocityDVI Transmitter to the
VX40 using multi-mode fiber-
optic cables (up to 1000 meters).
Connect cable L1 to any
Upstream Receive Port and cable
L2 to the same numbered
Upstream Transmit Port
as shown.(See the Digital
Crosspoint Switch detail
diagram, below.)
Visit us online at www.thinklogical.com for more product information, current updates and the complete line of Thinklogical™products.
STEP 7: Connect the Controller Card LAN Port
to your Controller CPU with a CAT5 cable.
(IP address: 192.168.13.15)
External Control CPU
Network Hub 7
USB
2.0
5
  • Page 1 1

Thinklogical VX40 Matrix Switch Quick start guide

Thinklogical
Brand
Thinklogical
Model
VX40 Matrix Switch
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents