Door Window Sensor is a full-featured security transmitter
with industry-leading wireless range and battery life. It is
typically used to sense opening and closing of doors and
windows, but can secure just about anything using its two
external contact zones. It will alarm when the magnet is
pulled away from the sensor or when an external contact is
opened.
Features
• Industry-leading wireless range and battery life
• One door window zone and two external contact zones
• Secure encrypted wireless transmissions
• 5 year warranty
Enroll by placing the panel into learn mode and then tripping
the sensor 3 times, waiting several seconds between trips, or
by entering the serial number on the back of the sensor.
Loop Conguration
• Loop 1= Optional External Contact Zone 1
(Terminals A and Common)
• Loop 2= Reed Switch
• Loop 3= Optional External Contact Zone 2
(Terminals B and Common)
• Loop 4= Tamper
Install by mounting the sensor and magnet on a door or
window using the mounting screw locations. Make sure to
align the alignment marks on the sensor and magnet when
mounting. Additionally, the sensor can be used with up to
two external contacts.
External Contacts
• Use normally-closed contacts because the door
window sensor will transmit an alarm when it sees
an external contact open.
• Do not use end-of-line resistors.
• Wire contact wires to one or both outside
terminals, using the center terminal as common.
Mounting Screw Holes
Use the panel installation guide to verify proper system setup.
RE201 Door Window Sensor
Honeywell® Compatible
I
N
S
T
A
L
L
G
U
I
D
E
I
Resolution Compatibles
Pro Tips
3M™ VHB™ Tape works great if the surface is properly prepared and rm pressure is
applied for over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50 °F
Wireless performance is optimized when mounted near the top of the door in a vertical
orientation.
OK BESTWRONG
Wire an external contact by securing one wire to either the external 1 or external 2 port
and the other wire to the common port. If both external contacts are used two wires
will be inserted into the common port.
Battery
-+
Cover Tamper
r
nal 1
m
nal 1
Loop 2
Magnetic Reed Switch
Loop 1
Outer Terminal Zone
Loop 3
Inner Terminal Zone
Center Common
Terminal
Loop 4
Tamper
Magnet Gap Specications
X Axis
Z Axis
Non-Ferromagnetic Surface
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
1.00 inches (2.5 cm)
1.10 inches (2.8 cm)
1.30 inches (3.3 cm)
2.40 inches (6.1 cm)
2.55 inches (6.5 cm)
1.20 inches (3.0 cm)
1.35 inches (3.5 cm)
Ferromagnetic Surface
Nominal Mounting Distance
X Axis - Make
Break
Y Axis - Make
Break
Z Axis - Make
Break
0.50 inches (1.2 cm)
0.60 inches (1.5 cm)
0.65 inches (1.7 cm)
1.70 inches (4.3 cm)
1.75 inches (4.5 cm)
1.05 inches (2.7 cm)
1.10 inches (2.9 cm)
Y Axis
Specications subject to change without notice
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
3.25 x 1.40 x 1.05 inches (8.3 x 3.6 x 2.7 cm)
1.90 ounces (54 grams)
Four #6 screws (provided)
Environmental
Operating Temperature
Maximum Humidity
32° to 120 °F (0° to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Replacement Battery
Nominal Battery Life
Battery Voltage
Current Draw
Transmitted Indications
Max Wire Length on
External Contacts
345 MHz
One Panasonic® CR123A
10 to 15 years
3.0 VDC (Nominal), 2.2 VDC (Low)
20 mA (Maximum), 0.6 uA (Quiescent)
Cover Tamper, Low Battery, Supervision
7.5 feet
Certication
RE201 FCC, IC
Specications
47-0004-02 • REV C • 2018-12-11
Tech Support Line • (888) 88-ALULA • (888) 882-5852
alula.net
01
WARRANTY
Alula will replace non-portable products that are defective in their
rst ve (5) years, and portable products that are defective in their
rst two (2) years.
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE201
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could void
the user’s authority to operate this equipment.
FCC ID: U5X-RE201X
TRADEMARKS
Alula is a trademark owned by Alula Holdings, LLC.
“Honeywell” is a trademark owned by Honeywell International Inc.
Alula products will function with Honeywell systems. However, no
Alula product is produced by, endorsed by, or is ofcially associated
with Honeywell. Alula recommends verifying proper enrollment and
operation, per control panel installation instructions, at installation.
3M and VHB are trademarks owned by 3M Company.
Panasonic is a trademark owned by Panasonic Corporation.
-
1
-
2
-
3
-
4
