Page is loading ...
LEDglo Refrigeration Light
Horizontal Refrigeration Shelf Light
Before you begin, read these instructions completely
and carefully. If you have any questions regarding
the proper use, installation, or safety considerations
of this product, please visit our website or contact
spirit LED Lighitng.
Spirit LED Lighting
1200 Valwood Pkwy.
Carrollton TX. 75006
Tel + 1-972-444-8400
Fax + 1-972-444-8424
Your kit includes:
* Model: LEDglo
* Mounting Brackets (Qty 2)
* #8 Self-Taping Screws (Qty 4)
* 75W Power Supply
* TYCO 6-WAY DISTRIBUTOR (Qty 1)
* Extension power cables
* 1/8” Drill Bit
* Wire Cutters
* Phillips Head Screwdriver
www.spiritledlighting.com
Thank you for purchasing Spirit LED LIghting
Horizontal Fixture Shelf Light.
Model: LEDglo
PRODUCT SPECIFICATIONS
Luminaire
Power Supply
PARAMETER
PARAMETER
VALUE
VALUE
In mm
Case Length
8.34 212.00
Case Width 1.70 43.00
Case Height 1.18 30.00
Mounting Lenght 9.45 240.00
Mounting Width 1.22 31.00
Overall Length 9.45 240.00
PS24V100W-01
TYCO 6-WAY DISTRUBUTOR
Tools needed:
Input Power
Rated Power Output
8 Watts
75 Watts (100 Watts Max)
24V DC
24V DC
*Due to constant power design input (Lin)
will vary depending on input voltage. Be
sure to size wire awg accordingly for worst
case input voltage.
Spirit LED Lighting
1200 Valwood Pkwy.
Carrollton TX. 75006
Tel + 1 972-444-8400
Fax + 1 972-444-8424
Product information is subject to change without notice.
® 2010 Spirit LED Lighting. All Rights Reserved.
www.spiritledlighting.com
-25 to 40C
4.1 Amps
120/277V AC
Dry, Damp
50/60 HZ
-40 to +55C
Dry, Damp
Input Voltage Range
Voltage Range
Humidity
Input Voltage
Operating Temp. Range
Output Current
Environment
Input Frequency
Operating Temp. Range
Environment
Installation Guide
Prepare Display Case
Installing the mounting brackets
Installing the LEDglo to the mounting brackets
DANGER: RISK OF ELECTRICAL SHOCK OR FIRE. DISCONNECT POWER BEFORE INSTALLATION
INSTALLATION INSTRUCTIONS - LIGHT FIXTURE
Before you begin, read these instructions completely and carefully. If you have any questions regarding the proper use,
installation, or safety considerations of this product, please visit our website or contact spirit LED Lighitng.
● Then turn AC power off to the display case.
● Disconnect all power to the lamp xture.
● Remove uorescent tubes. Dispose of tubes properly.
● Remove the ballast and starter where applicable.
● Remove and replace original “tombstone” lamp
holders with provided mounting brackets.
● Determine the mounting position of the rst bracket
in light troffer.
● Drill 2 pilot holes (specify size and spacing of holes
for bracket).
● Measure for second bracket and drill 2 pilot holes
(specify size and spacing of holes for bracket and
distance from rst bracket.
● Install the LEDglo canopy light in the mounting
brackets so that the LEDglo power cable is at the end
of the light troffer with the cable exit.
● Feed the LEDglo canopy light power cable through
the cable exit in the troffer into the display cabinet.
● Once the power cable is fed through the cable exit,
connect the extension power calbes to the light
power cable.
Spirit LED Lighting
1200 Valwood Pkwy.
Carrollton TX. 75006
Tel + 1 972-444-8400
Fax + 1 972-444-8424
Product information is subject to change without notice.
® 2010 Spirit LED Lighting. All Rights Reserved.
www.spiritledlighting.com
AC
120 - 277V
Fluorescent Lamp
Fluorescent
Ballast
x.x”
Light Troffer
Light Troffer
Hole Dia. (x2)
Distance Inches
Bracket
Power Cable
LEDglo Refrigeration Light
Horizontal Fixture Canopy Light
Before you begin, read these instructions completely
and carefully. If you have any questions regarding
the proper use, installation, or safety considerations
of this product, please visit our website or contact
spirit LED Lighitng.
Spirit LED Lighting
1200 Valwood Pkwy.
Carrollton TX. 75006
Tel + 1-972-444-8400
Fax + 1-972-444-8424
Your kit includes:
* Model: LEDglo
* Mounting Brackets (Qty 2)
* #8 Self-Taping Screws (Qty 4)
* 75W Power Supply
* TYCO 6-WAY DISTRIBUTOR (Qty 1)
* Extension power cables
* 1/8” Drill Bit
* Wire Cutters
* Phillips Head Screwdriver
www.spiritledlighting.com
Thank you for purchasing Spirit LED LIghting
Horizontal Fixture Canopy Light.
Model: LEDglo
PRODUCT SPECIFICATIONS
Luminaire
Power Supply
PARAMETER
PARAMETER
VALUE
VALUE
In mm
Case Length
8.34 212.00
Case Width 1.70 43.00
Case Height 1.18 30.00
Mounting Lenght 9.45 240.00
Mounting Width 1.22 31.00
Overall Length 9.45 240.00
PS24V100W-01
TYCO 6-WAY DISTRUBUTOR
Tools needed:
Input Power
Rated Power Output
30 Watts
75 Watts (100 Watts Max)
24V DC
24V DC
*Due to constant power design input (Lin)
will vary depending on input voltage. Be
sure to size wire awg accordingly for worst
case input voltage.
Spirit LED Lighting
1200 Valwood Pkwy.
Carrollton TX. 75006
Tel + 1 972-444-8400
Fax + 1 972-444-8424
Product information is subject to change without notice.
® 2010 Spirit LED Lighting. All Rights Reserved.
www.spiritledlighting.com
-25 to 40C
4.1 Amps
120/277V AC
Dry, Damp
50/60 HZ
-40 to +55C
Dry, Damp
Input Voltage Range
Voltage Range
Humidity
Input Voltage
Operating Temp. Range
Output Current
Environment
Input Frequency
Operating Temp. Range
Environment
Installation Guide
Prepare Display Case
Installing the LEDglo shelf light
DANGER: RISK OF ELECTRICAL SHOCK OR FIRE. DISCONNECT POWER BEFORE INSTALLATION
INSTALLATION INSTRUCTIONS - LIGHT FIXTURE
Before you begin, read these instructions completely and carefully. If you have any questions regarding the proper use,
installation, or safety considerations of this product, please visit our website or contact spirit LED Lighitng.
● Then turn AC power off to the display case.
● Disconnect all power to the lamp xture.
● Remove uorescent tubes. Dispose of tubes properly.
● Remove the ballast and starter where applicable.
● Remove and replace original “tombstone” lamp
holders with provided mounting brackets.
● Attach mounting brackets to the light.
● Attach mounting brackets to the shelf using self
tapping screws.
● Feed LEDglo shelf light power cable through the
pre-existing hole in the shelf into the display cabinet.
● Once the power cable is fed through the pre-existing
hole, connect the exstension power cable to the light
power cable.
● Once the LEDglo shelf light has been installed, attach
the supplied warning label nearby the installed light.
Spirit LED Lighting
1200 Valwood Pkwy.
Carrollton TX. 75006
Tel + 1 972-444-8400
Fax + 1 972-444-8424
Product information is subject to change without notice.
® 2010 Spirit LED Lighting. All Rights Reserved.
www.spiritledlighting.com
AC
120 - 277V
Fluorescent Lamp
Fluorescent
Ballast
Power Cable
/
