IXL 10646 classic with timer Installation & Operating Instructions

FAX

IXL Appliances NZ Ltd

PO Box 100755,

North Shore Mail Centre, Auckland

0800 806 664

(09) 476 0028

IXL Appliances Service Division

A division of Backwell IXL Pty Ltd ACN 005 326 009

PO Box 818, Geelong, Victoria 3220

1800 032 558

1800 032 024

APPLIANCES

4.5kW

10636 Classic, 10646 Classic with Timer

Models: 10174 Hotline, 10634 Classic

6kW Models: 10176 Hotline,

& Classic

Hotline

Installation

Instructions

Semi Recessed

Space HeaterElectric

The benefits conferred by this warranty are in addition to all other rights and remedies in respect of

the product which the consumer has under the Trade Practices Act and similar state and territory laws.

Under this warranty, for a period of two years from the date of purchase, IXL Appliances undertake to

replace or make good any parts which are proven to be defective. The warranty applies only if:

1. The unit is installed and used in accordance with the manufacturer’s instructions.

2. The defects were not caused by changes or modifications made by unauthorised persons.

EXCLUSIONS:

This warranty does not cover damage or loss caused by:

a. Misuse, negligence or faults due to incorrect installation

b. Improper wiring circuits or fuses

c. Attempts to repair the appliance by unauthorised people

d. Failure to install and maintain the appliance in accordance with the manufacturer's instructions.

The benefit conferred by this warranty are in addition to all other rights and remedies in respect of the product

which the consumer has under the Trade Practices Act and similar state and territory laws.

If the unit fails to function, before calling for service please check the following:

1. Check that switch is ON and neon indicator is glowing

2. Check that the electrical supply is on at the switchboard and the fuse is intact

3. Check that the thermostat is set correctly

Should the unit require service, please contact your nearest IXL Service Centre:

IMPORTANT: The Warranty does not cover service calls related to incorrect operation. Should the unit

require service, switch it off and contact the manufacturer or state distributor.

Warranty

Service

Operation instructions

Manufactured & Warranted by:

BACKWELL IXL Pty Ltd. A.C.N. 005 326 009

Wood Street, East Geelong, Victoria, 3219, AUSTRALIA

Tel: 1800 032 558 Fax: 1800 032 024

APPLIANCES

P/No.611131

Safety Information

For safeoperation of yourheater, please ensure youobserve thefollowing points:

1. Donot cover orobstruct the air ventsof the heater.

4. Neverdrape the heaterwith clothes orother combustible materials.

5. Neveruse the heaterin the vicinityof paint thinners,petrol or othercombustible liquids.

6. Theheater is notintended for useby young childrenor infirm persons without supervision.

7. Young childrenshould be supervised to ensurethey do not play with the heater.

8. Do not allow water to splash on the heater. If theheater appears to be dump, do not switch the power

on.

9. Keep top and bottom air inlet and outlet grilles clear and unobstructed - clean externally with

vacuum cleaner.

2. Donot place anylarge obstructions within1 metre ofthe front ofthe heater.

3. Donot insert objectsthrough the airvents of theheater.

& Operation

CLEANING AND MAINTENANCE:

To heat one area only adjust rear register chain for one direction only.

Turn thermostat in unheated area to minimum setting. Adjust thermostat in heated area to obtain

desiredtemperature.

To heat both areas select temperature requiredin each area. Adjust rear register chain to give balanced

heating. Correct positionwillbe foundbytrial anderror.

When Fitted with Dual Thermostat Only:

(B.V. Models only)

To obtainheat throughrear register disengagechain andallow chainto be drawn backinto register. Lock

chainat anydesiredposition. Whenheating bothmain roomand reararea,use only"HI"selection.

Warmair canbe directedin either or both directions in anyproportion. Toheat main roompull chainin

rearregister outwardstofullextent and lockin position.

BACK VENT OPERATION:

Simplyswitch offtheredilluminated ON/OFF switch. DO NOT TURNDOWN THETHERMOSTAT.

TO TURN THE HEATER OFF:

Switch ON the red ON/OFF switch. To give faster

warmupusing bothheatingelements simply

When power is on the ON/OFF switch is illuminated.

switchHI ontheHI/LOswitch.

Set thermostat to 20°C.

The heater will operate and cycle on and off to maintain steady temperature in the room. Individual

requirements may require adjustments to thermostat setting but for economy use the lowest setting at

whichcomfort isobtained.

When the room has reached comfort level, select "LO" on the HI/LO switch and use this selection

whenever possible for optimum distribution and economy. For best results and comfort, do not sit too

closeto heaterorobstructoutlet with furniture.

Note:

The heater will not operate unless the room temperature is below that selected on the thermostat.

TO HEAT:

(i)2 switcheson heatercontrolling:

-ON/OFF switch(red illuminated)

-HI/LO switch(red) which selects oneor bothelements

(ii) Remote thermostat (wall mounted)

CONTROLS:

For satisfactory performance of your IXL electric space heater please read these instructions carefully.

To save on running costs you should insulate the ceilings of your home. This will help keep your home

warmin winterandcool insummer.

For additional assistance in the use of your heater contact your electrical authority showroom, the

manufactureror StateDistributor.

INTRODUCTION

Additional Warning

Before using your IXL space heater for the first time or if the heater has not been used

recently, the areawhere the heater is used MUST be well ventilatedfor atleast 2 hours.

As with any new heating appliance, certain effects such as faint odour may occur. These are

part ofthe NORMAL running-in process and will disappear.

FAX

The only moving part in your heater is the fan unit which is designed for long life. To maximize the life

of the heater we recommend that it be cleaned internally by a qualified electrician/service agent every

two years or as required.

: During maintenance and service ensure heater is electrically isolated.IMPORTANT

All external surfaces should be cleaned using warm water and mild detergent. Do not use abrasives as

scratchingwill occur.

CONGRATULATIONS ON PURCHASING OF BACKWELL IXL ELECTRIC SPACE HEATER

Owners Warranty and Service Record

Complete and keep the following information as it is vital for warranty claims and service calls.

Ensure you maintain proof of purchase including date.

Cat./Model Number ............................................ Serial Number ..........................................................

Date Purchased .......... /................ /............. Installed by ....................................................................

Please read these instructions completely before commencing installation

1. Inspect the heater for damage before proceeding with installation.

2. All models must be installed by a registered electrician.

3. Ensure an isolating switch is incorporated in supply wiring, and that this switch isolates all live

connections to the heater.

4. Unit must be installed in accordance with Wiring Rules AS/NZS 3000:2000.

Installation

Poor

Good

Locating the heater

Chose a location to give good distribution of warm air

through the room. Avoid corners to allow spread of warm

air (see Fig.1) Do not install close to or directly opposite

furniture,or nearcurtainsor drapes.

Electrical supply requirements:

Removetwo screwsinlowergrille.

Using screwdriver through slots in top of front panel,

remove jacknuts and discard angle from two screws

securingfront totopof heater.Check thatfan spinsfreely.

To remove front

Min.Distance betweenstuds393 mm(15 “)(see Fig.2).

Min. depth of stud plus one thickness of wall cladding 88

mm(3 ½").

Top ofskirting should beno lessthan 60 mm(2 ¼")and no

morethan 100mm(4")above floorcovering(see Fig.3).

Breakplasterboard awayfrombehind skirtingboard.

Fig. 3

Cavity preparation:

Installation in a stud wall

Clearance between underside of heater surround and top of floor covering must not be less than 65 mm

(2 “)- seeFig 3.½

Important

It is important that a clearance of at least 6

mm (¼") be maintained between the back, side

and top surfaces of the heater rear box ( and

back vent stub if fitted) and the wall cavity into

which it is fitted.

Stand -off spacers are incorporated in the design

to indicate the clearances required.

Clearances

Additionally 25mm (1") to be maintained

between these surfaces and any adjacent

material

415mm

393mm

Skirting board

625mm

Tongues

65 mm min

60 - 100 mm

Thermostat wires

Jacknuts

To set jacknut drill 9.5mm (3/8“) diameter hole in wall

cladding. Push jacknut into hole. Pass metal thread screw

through friction wrench and into jacknut. Hold friction

wrench against jacknut and tighten screw, remove screw,

jacknutremains captive(seeFig.4)

Tongues

Skirting board

Friction wrench

Jacknut in wall

Installation in brick chimney

Cut

832 mm max.

415mm apart

Dummy studs

if required

583 mm min

665 mm max

411 mm min.

If necessary, cut off

2 tabs as shown

Drill flanges and attach screws as required

External wiring:

Isolating switch to be installed in accordance

withclause 4.3.53 ofAS/NZS3000:2000.

A circuit breaker is accepted as an isolating

switch(see Fig.8).

Note: For 2 phase supply remove

bridge between A1 and A2

For thermostat location and installation please refer to thermostat Installation Instructions supplied

withthe thermostat.

For thermostat connection to the thermostat terminal block refer to Fig. 10 (for Models 10634, 10636,

1074and 1076)or toFig. 11forModel 10646. Recommendedwire 1.0mm T.P.S.

Thermostat location and installation

Please leave Operation Instructions and Warranty with heater or hand to householder.

Mr INSTALLER

To check operationset thermostat to asetting higher than roomtemperature and select "LO" and"ON".

Thefan onlowspeed andone heating element should operate.

Then select "HI", the second elementshould beenergized andfan willrun onhigh speed,giving fasterair

flowand higheroutlettemperature.

NOTE:When ON/OFFswitchisON, neonglowscontinuously oneitherLO orHI setting.

Check that unit functions

Fix front to heater through lower grille with 2 long

metal thread screws, using serrated lock washers.

Tightenall 4screws (seeFig. 12and13).

Discardplastic filmfrom decaland switches.

Hook front of heater over lip on upper edge of

heater, making sure switches and decal do not

catchon apertureedge.

Pushtop fullydown (seeFig. 12).

To fit front to heater

A1 9.5A

A2 9.5A

A1 12.5A

A2 12.5A

A1 19A

A1 25A

240/230 V 50 Hz

Two phase*

Single phase

The terminal block is completed with clamp plate. Please make

sure that wire enters terminal block above the clamp plate (see

Fig.9). Nocontact willbemade ifwire entersbelow clampplate.

Important

For additional information or name of your nearest agent please phone (03) 5222 2922

Electric cable

HotlineModel 10174and10176 only.

Cap off chimney to prevent rain entry. Allow some ventilation to prevent dampness. Fix to brick or

alternativelyprovide dummystuds.

Model No.s 10174 and 10634 4.5kW 19A

Model No.s 10176, 10636 & 10646 6kW 25A

*NOTE: For 2 phase supply remove bridge between A1 and A2 (see Fig. 8).

Fig. 2

Fig. 1

Fig.4

Fig. 5.

Fig. 7

Fig. 6

Lower flangeof heaterbehind skirting. Tongues rest ontop ofskirting board(see Fig.5). Make electrical

connectionsand tightenALLterminals.

Fixto wallas indicated,engaging two topscrews intojacknutsbut donotfully tightenat thisstage.

To attach heater’s body to wall

Fig. 9

Wallboard

Top edge

of heater

Heater

front

Fig. 12

Skirting board

Rubber

Retaining

Ring

Serratted washer

Tongues

Fig. 13

Connection of thermostat to heater

Model 10646 - Classic with timer

Fig. 11

From thermostat through

hole between relay and

switch bracket

with 2A fuse

Thermostat terminal block

NOTE: Thermostat circuit is protected by 2A fuse which is inserted into the thermostat terminal block fuse

holder.

White

Red

Blue

CLAMP PLATE

NA2A1

Earth

Isolating switch

Connection of power supply for single phase

Power terminal block

Bridge

Fig. 8

Power terminal block

Power supply

Connection of thermostat to heaters

Model No: 10174, 10634, 1063610176,

White

Red

Blue

Capacitor

From thermostat through

hole between relay and

switch bracket

Fig. 10

with 2A fuse

Thermostat terminal block

IXL 10646 classic with timer, 10634 classic, 10636 classic Installation & Operating Instructions

Related papers

Other documents