Biostar NF61V Micro AM2 SE User manual

Category
Motherboards
Type
User manual

This manual is also suitable for

NF61V Micro AM2 SE/NF61S Micro AM2 SE
Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable pro tec tion against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not ins talled and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference wil l not occur in a particula r ins talla tion.
The ve ndo r makes no represe nta tio ns or wa rranties with respec t to the
contents here and specially disclaims any implied warranties of merchantability
o r fi tn es s fo r a ny p u rp os e . F urt he r t he ve nd o r res e rves t he ri g ht to r ev is e t h is
publication and to make changes to the contents here without obligation to
notify any party beforehand.
D uplica tion of this publicatio n, in pa rt or in whole , is not al lowed wit hout fi rst
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be res ponsible for any mis takes found in this users manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction .............................................1
1.1 Before You Start................................................................... 1
1.2 Package Checklist................................................................1
1.3 Motherboard Features.......................................................... 2
1.4 Rear Panel Connectors (Ver 6.x)............................................ 4
1.5 Rear Panel Connectors (Ver 5.x)............................................ 4
1.6 Motherboard Layout (Ver 6.x)............................................... 5
1.7 Motherboard Layout (Ver 5.x)............................................... 6
Chapter 2: Hardware Installation ..............................7
2.1 Installing Central Processing Unit (CPU)................................ 7
2.2 FAN Headers........................................................................ 9
2.3 Installing System Memory.....................................................10
2.4 Connectors and Slots............................................................12
Chapter 3: Headers & Jumpers Setup......................14
3.1 How to Setup Jumpers..........................................................14
3.2 Detail Settings.....................................................................14
Chapter 4: RAID Functions.......................................22
4.1 Operation System................................................................22
4.2 Raid Arrays.........................................................................22
4.3 How RAID Works.................................................................22
Chapter 5: Useful Help ..............................................24
5.1 Driver Installation Note .......................................................24
5.2 Award BIOS Beep Code........................................................25
5.3 Extra Information................................................................25
5.4 Troubleshooting...................................................................27
Chapter 6: WarpSpeeder .......................................28
6.1 Introduction........................................................................28
6.2 System Requirement............................................................28
6.3 Installation.........................................................................29
6.4 WarpSpeeder™....................................................................30
Appendencies: SPEC In Other Language ................36
German................................................................................................36
France..................................................................................................38
Italian..................................................................................................40
Spanish................................................................................................42
Portuguese...........................................................................................44
Polish...................................................................................................46
Russian................................................................................................48
Arabic..................................................................................................50
Japanese..............................................................................................52
NF61V Micro AM2 SE/NF61S Micro AM2 SE
1
CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU START
Tha nk yo u fo r choo sing our pro duct. Be fore yo u s ta rt installing the
mo the rboa rd , plea se make sure you fo llo w the ins tru ctio ns be low:
Prepare a dry and stable working environment with
s uf ficie nt ligh ting .
Always disconnect the computer from power outlet
be fo re ope ra tion .
Befo re you take the mo the rboa rd ou t f rom a n ti -s ta ti c
bag, ground yourself properly by touching any safely
grounde d appliance, o r use gro unded wrist strap to
remove the static charge.
Avo id tou ch ing the compone nts o n m o the rboa rd o r the
rear side of the boa rd unles s ne cessa ry. Hold the bo a rd
on the edge , do not try to be nd or flex the boa rd.
Do no t lea ve any unfastene d sma ll pa rts inside the
case after installation. Loose parts will cause short
circuits which ma y damage the equipment.
Keep the computer from dangerous area, such as heat
so urce , humid a ir and wa te r.
1.2 PACKAGE CHECKLIST
FDD Cable X 1
HDD Cable X 1
Use r’s Manua l X 1
Fully Setup Driver CD X 1
Rear I/O Panel for ATX Case X 1
Se ria l ATA Cab le X 1 ( op tiona l)
USB 2.0 Cable X1 (optional)
S/PDIF Cable X 1 (optional)
Se ria l ATA Po we r Switch Cab le X 1 (op tiona l)
Printe r Po rt Cable X 1 (optional)
Motherboard Manual
2
1.3 MOTHERBOARD FEATURES
NF61V Micro AM2 SE NF61S Micro AM2 SE
CPU
Socket AM2
AMD Sempron / Athlon 64 / Athlon 64 FX /
Althlon 64 X2 processors
Supports Hyper Transport and Cool=n=Quiet
Socket AM2
AMD Sempron / Athlon 64 / Athlon 64 FX /
Althlon 64 X2 processors
Supports Hyper Transport and Cool=n=Quiet
FSB Supports up to 1GHz Bandwidth Supports up to 1GHz Bandwidth
Chips et MCP61V ( GeForce 61 00- 40 0) MCP61S ( GeForc e 61 00- 40 5)
Super I/O
ITE 8716F
Provides the most commonl
y
us e d l e
g
ac
y
Su
p
e
r
I/O functionality.
Low Pin Count Interface
ITE 8716F
Provides the most commonly used legacy Super
I/O functionality.
Low Pin Count Interface
Main
Memory
DIMM Slots x 2
Eac h DIMM s upports 256/512MB & 1GB DDR2
Max Memory Capicity 2GB
Dual Channel Mode DDR2 memory module
Supports DDR2 400 / 533 / 667 / 800
DIMM Slots x 2
Eac h DIMM s upports 256/512MB & 1GB DDR2
Max Memory Capicity 2GB
Dual Channel Mode DDR2 memory module
Supports DDR2 400 / 533 / 667 / 800
Graphics
Integrated in MCP61V Chipset
Max Shared Video Memory is 256MB
Integrated in MCP61S Chipset
Max Shared Video Memory is 256MB
IDE
Integrated IDE Controller
Ultra DMA 33 / 66 / 100 / 133 Bus Mas ter Mode
supports PIO Mode 0~4
Integrated IDE Controller
Ultra DMA 33 / 66 / 100 / 133 Bus Mas ter Mode
supports PIO Mode 0~4
SA TA II
Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
SATA Version 2.0 specification compliant.
Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
SATA Version 2.0 specification compliant.
LAN
Realtek 8201CL PHY
10 / 100 Mb/s Auto-Negotiation
Realtek 8201CL PHY
10 / 100 Mb/s Auto-Negotiation
Sound
ALC861VD(Ver 6.x) / ALC888(Ver 5.x)
5. 1 channels audio out (Ver 6. x)
7. 1 channels audio out (Ver 5. x)
Intel High-Definition Audio support
ALC861VD(Ver 6.x) / ALC888(Ver 5.x)
5. 1 channels audio out (Ver 6. x)
7. 1 channels audio out (Ver 5. x)
Intel High-Definition Audio support
PCI slot x2 PCI slot x2
PCI Express x16 slot (x1 Speed) x1 PCI Express x 16 slot (x8 Speed) x1
Slots
PCI Express x 1 slot x1 PCI Express x 1 slot x1
NF61V Micro AM2 SE/NF61S Micro AM2 SE
3
NF61V Micro AM2 SE NF61S Micro AM2 SE
Floppy c onnector x1 Floppy c onnector x1
IDE Connector x1 IDE Connector x1
SA TA 2 C onnect or x2 SATA 2 C onnect or x2
Front Panel Connector x1 Front Panel Connector x1
Front Audio Connector x1 Front Audio Connector x1
CD-i n Connec tor x1 CD-in Connec tor x1
S/PDIF out connector x1 S/PDIF out connector x1
S/PDIF in connector(O ptional) x1 S/PDIF in c onnector(O ptional) x1
CPU Fan header x1 CPU Fan header x1
Sys tem Fan header x1 S ys tem Fan header x1
CMOS clear header x1 CMOS clear header x1
USB connector x2 USB connector x2
Printer Port Connector x1 Printer Port Connector x1
Chassis open header(O ptional ) x1 Chassis open header(O ptional ) x1
Power Connector (24pin) x1 Power Connector (24pin) x1
On Board
Connector
Power Connector (4pin) x1 Power Connector (4pin) x1
Back Panel
I/O
PS/2 Keyboard x1
PS/2 Mouse x1
S e ri a l Po rt x 1
VGA port x1
LAN port x1
USB Port x4
Audio Jack (Ver 6.x) x3
Audio Jack (Ver 5.x) x6
PS/2 Keyboard x1
PS/2 Mouse x1
S e ri a l Po rt x 1
VGA port x1
LAN port x1
USB Port x4
Audio Jack (Ver 6.x) x3
Audio Jack (Ver 5.x) x6
Board S iz e 207 x 244 (mm) Mic ro A TX Siz e B oard 207 x 244 (mm) Mic ro A TX Siz e B oard
Special
Features
NVIDIA nTunes
RAID 0 / 1 s upport
NVIDIA nTunes
RAID 0 / 1 s upport
OS Support
Windows 2000 / XP / VIS TA
Biostar Reserves the right to add or remove
support for any OS With or without notice.
Windows 2000 / XP / VIS TA
Biostar Reserves the right to add or remove
support for any OS With or without notice.
Motherboard Manual
4
1.4 REAR PANEL CONNECTORS (VER 6.X)
PS/2
Mouse
PS/2
Keyboard
USBX2USBX2
LAN
COM1 VGA
Line In/
Surround
Line Out
Mic In 1/
Bass/ Center
1.5 REAR PANEL CONNECTORS (VER 5.X)
PS/2
Mouse
PS/2
Keyboard
USBX2USBX2
LAN
COM1 VGA
Line In
Line Out
Mic In
Center
Rear
Side
NF61V Micro AM2 SE/NF61S Micro AM2 SE
5
1.6 MOTHERBOARD LAYOUT (VER 6.X)
JKBMS1
JCOM1
JVGA1
JUSB1
JUSBLAN1
JAUDIO1
LAN
Code c
JC DIN 1 J SPDI F_OU T1 JPRNT1
FDD1
Super I/O
BI OS
JPANEL1
JSFAN 1
JUSB3
JUSB2
JCMOS1
J USB V2
SATA 2 SATA 1
IDE1
DI MM A 1
DI MM B 1
JDDRII_22V1
Socket A M2
JATXPWR2
JUSBV1
JATXPWR1
JNFAN1(Optional)
PEX1_1
PCI1
PCI2
BAT1
JAUDIOF1
JCI1(Optional)
JCFAN1
PEX16_1
MCP61V
or
MCP61S
JSPDIF_IN1(Optional)
No te: represents the 1
st
pin.
Motherboard Manual
6
1.7 MOTHERBOARD LAYOUT (VER 5.X)
JKBMS1
JCOM1
JVGA1
JUSB1
JUSBLAN1
JAUDIO1
LAN
Code c
JC DIN 1 J SPDI F_OU T1 JPRNT1
FDD1
Super I/O
BI OS
JPANEL1
JSFAN 1
JUSB3
JUSB2
JCMOS1
J USB V2
SATA 2 SATA 1
IDE1
DI MM A 1
DI MM B 1
JDDRII_22V1
Socket A M2
JATXPWR2
JUSBV1
JATXPWR1
JNFAN1(Optional)
PEX1_1
PCI1
PCI2
BAT1
JAUDIOF1
JCI1(Optional)
JCFAN1
PEX16_1
MCP61V
or
MCP61S
JSPDIF_IN1(Optional)
No te: represents the 1
st
pin.
NF61V Micro AM2 SE/NF61S Micro AM2 SE
7
CHAPTER 2: HARDWARE INSTALLATION
2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Remove the socket protection cap.
Step 2: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 3: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
Motherboard Manual
8
Step 4: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the JCFAN1. This completes the installation.
NF61V Micro AM2 SE/NF61S Micro AM2 SE
9
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header
Pin
Assignment
1 Ground
2 +12V
3
FAN RPM rate
sense
14
JCFAN1
4 Smart Fan
Control (By Fan)
JSFAN1: System Fan Header
JNFAN1: North Bridge Fan Header (Optional)
Pin Assignment
1 Ground
2 +12V
13
1
3
JNFAN1
(Optional)
JSFAN1
3
FAN RPM rate
sense
Note:
The JCFAN1JSFAN1 and JNFAN1 support 4-pi n and 3-pin head connector. When
connecting with wires onto connectors, please note that the red wire is the positi ve and
shoul d be connected to pi n#2, and the bl ack wire is Ground and should be connected to
GND.
Motherboard Manual
10
2.3 INSTALLING SYSTEM MEMORY
A. Memory Modules
DIMMA
1
DIM MB
1
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
NF61V Micro AM2 SE/NF61S Micro AM2 SE
11
B. Memory Capacity
DIMM Socket
Location
DDR Module Total Memory Size
DIMMA1 256MB/512MB/1024MB *1
DIMMB1 256MB/512MB/1024MB *1
Max memory 2GB.
C. Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pair, shown in the following table.
Dual Channel Status
DIMMA1
DIMMB1
Disabled O X
Disabled X O
Enabled O O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
Motherboard Manual
12
2.4 CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
133
2
34
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode
0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.
1
39
2
40
NF61V Micro AM2 SE/NF61S Micro AM2 SE
13
PEX1_1: PCI-Express x1 Slot
- PCI-Express 1.0a compliant.
- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.
- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
- 2X bandwidth over the traditional PCI architecture.
PEX16_1: PCI-Express x16 Slot (x1 Speed)
(for NF61V Micro AM2 SE)
- PCI-Express 1.0a compliant.
- Maximum theoretical realized bandwidth of 250MB/s simultaneously per
direction, for an aggregate of 500MB/s totally.
PEX16_1: PCI-Express x16 Slot (x8 Speed)
(for NF61S Micro AM2 SE)
- PCI-Express 1.0a compliant.
- Maximum theoretical realized bandwidth of 2GB/s simultaneously per
direction, for an aggregate of 4GB/s totally.
PEX1_1
PEX16_1
PCI1~PCI2: Peripheral Component Interconnect Slots
This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
Motherboard Manual
14
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 HOW TO SET UP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper isclose”, if not, that means the jumper is
open”.
Pin opened Pin closed Pin1-2 closed
3.2 DETAIL SET T ING S
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep
button and speaker connection. It allows user to connect the PC case’s front
panel switch functions.
S
L
P
P
W
R
_
L
E
D
O
n
/
O
f
f
R
S
T
H
L
E
D
S
P
K
+
+
+
-
-
1
9
16
8
Pin Assignment Function Pin Assignment Function
1 +5V 9 Sleep control
2 N/A 10 Ground
Sleep button
3 N/A 11 N/A N/A
4 Speaker
Speaker
Connector
12 Power LED (+)
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
Hard drive
LED
14 Power LED (-)
Power LED
7 Ground 15 Power button
8 Reset control
Reset button
16 Ground
Power-on button
NF61V Micro AM2 SE/NF61S Micro AM2 SE
15
JATXPWR1: ATX Power Source Conne ctor
This connector allows user to connect 24-pin power connector on the ATX
power supply.
1
12
13
24
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
JATXPWR2: ATX Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
Pin
Assignment
1 +12V
2 +12V
3 Ground
12
34
4
Ground
Motherboard Manual
16
JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
8 Ground
9 Key
1
9
210
JUSB2
JUSB3
10 NC
JUSBV1/JUSBV2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at JUSBLAN1.
JUSBV2: +5V for USB ports at front panel (JUSB2/JUSB3).
Pin 2-3 Close:
JUSBV1: USB ports at JUSBLAN1 are powered by +5V standby voltage.
JUSBV2: USB ports at front panel (JUSB2/JUSB3) are powered by +5V
standby v oltage.
13
1
3
Pin 1-2 close
13
1
3
JUSBV2
JUSBV1
13
1
3
Pin 2-3 close
Note:
In order to support this function “Power-On system vi a USB device,”JUSBV1/ JUSBV2”
jumper cap should be placed on Pin 2-3 indi viduall y.
NF61V Micro AM2 SE/NF61S Micro AM2 SE
17
JAUDIOF1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. It will disable the output on back panel audio connectors.
Pin Assignment
1 Mic in
2 Ground
3 Mic power
4 Audio power
5 Right line
out
6 Ground
7 Reserved
8 Key
9 Left line out
10 Ground
1
9
2
10
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.
Pin
Assignment
1 Left Channel
Input
2 Ground
3 Ground
14
4 Right Channel
Input
Motherboard Manual
18
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
13
Pin 1-2 Close:
Normal Operation
(default).
1
3
13
Pin 2-3 Close:
Clear CMOS
data.
Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper toPin 2-3 close.
3. Wait for five seconds.
4. Set the jumper toPin 1-2 close.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
JCI1: Chassis O pen Header (Optional)
This connector allows system to monitor PC case open status. If the signal has
been triggered, it will record to the CMOS and show the message on next
boot-up.
Pin
Assignment
1 Case open
signal
1
2
2 Ground
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91

Biostar NF61V Micro AM2 SE User manual

Category
Motherboards
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages