Biostar A740G M2+ User manual

A740G M2+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protec tion against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particula r ins talla tion.

The vendor makes no representatio ns o r warranties with respec t to the

contents here and specially disclaims any implied warranties of merchantability

o r fi tnes s fo r a ny p u rpose . F urt he r t he ve nd or rese rves t he ri g ht to rev ise t his

publication and to make changes to the contents here without obligation to

notify any party beforehand.

D uplication of this publication, in part or in whole , is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be res ponsible for any mis takes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction.....................................................1

1.1 Before You Start................................................................... 1

1.2 Package Checklist................................................................1

1.3 Motherboard Features..........................................................2

1.4 Rear Panel Connectors.......................................................... 3

1.5 Motherboard Layout............................................................4

Chapter 2: Hardware Installation........................................5

2.1 Installing Central Processing Unit (CPU)................................5

2.2 FAN Headers........................................................................7

2.3 Installing System Memory......................................................8

2.4 Connectors and Slots............................................................10

Chapter 3: Headers & Jumpers Setup..............................12

3.1 How to Setup Jumpers..........................................................12

3.2 Detail Settings.....................................................................12

Chapter 4: RAID Functions...............................................19

4.1 Operation System................................................................19

4.2 Raid Arrays.........................................................................19

4.3 How RAID Works.................................................................19

Chapter 5: Useful Help.....................................................22

5.1 Driver Installation Note .......................................................22

5.2 Software .............................................................................23

5.3 Extra Information................................................................27

5.4 Troubleshooting...................................................................29

Appendencies: SPEC In Other Language.............................30

German................................................................................................30

France..................................................................................................32

Italian..................................................................................................34

Spanish................................................................................................36

Portuguese...........................................................................................38

Polish...................................................................................................40

Russian................................................................................................42

Arabic..................................................................................................44

Japanese..............................................................................................46

A740G M2+

1

CHAPTER 1: INTRODUCTION

1.1 BEFORE YOU START

Tha nk yo u for choosing our product. Be fore you start installing the

mo the rboa rd, plea se make sure you fo llow the instructions be low:

 Prepare a dry and stable working environment with

s ufficie nt ligh ting .

 Always disconnect the computer from power outlet

before ope ra tion .

 Befo re you take the mo the rboa rd ou t from a n ti -s ta ti c

bag, ground yourself properly by touching any safely

grounded appliance, or use gro unded wrist strap to

remove the static charge.

 Avo id tou ch ing the com pone nts o n mo the rboa rd o r the

rear side of the board unless necessary. Hold the boa rd

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source , humid air and wa ter.

1.2 PACKAGE CHECKLIST

HDD Cable X 1

Se ria l ATA Cab le X 1

Rear I/O Panel for ATX Case X 1

I ns talla tion Guide X 1

Fu lly Se tup Drive r C D X 1 (fu ll ve rs ion manua l files ins ide )

FDD Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

S/P DI F ou t Ca ble X 1 (op tiona l)

Se ria l ATA Po we r Cab le X 1 (o ptio nal)

Note: The package contents may differ by area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

S oc ket AM2+ / AM2

AMD Athlon 64 / A thlon 64 FX

/

Athlon 64 x

2

/ Sempron / Phenom processors

AMD 64 Architecture enables 32 and 64 bit

computing

Supports Hyper Transport 2.0 and Cool=n=Quiet

FSB

Support HyperTransport 2.0

Supports up to 2.0 GT/s Bandwidth

Chipset

AMD 740G

AMD SB700

Super I/O

ITE 8718F

Provides the most commonly used legacy

Super I/O functionality

Low Pin Count Interface

Environment Control initiatives

H/W Monitor

ITE's "Smart Guardian" function

Main

Memory

DDR2 DIMM Slots x 4

Max Memory Capacity 8GB

Eac h DIMM supports 256/512MB/1GB/2GB

DDR2

Dual Channel Mode DDR2 memory module

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (for AM2+ CPU only)

Registered DIMM and ECC DIMM is not supported

Graphics Integrated in AMD 740G Chipset

Max Shared Video Memory is 512MB

HDCP s upport

IDE Integrated IDE Controller

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

SA TA II I nt e gr at ed S eri al ATA C ont rol l er

Data transfer rates up to 3 Gb/s

SATA Version 2.0 specification compliant

LAN Realtek RTL 8101E

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Sound ALC662

5.1 channels audio out

High Definition Audio

PCI Express x16 slot x1 Supports PCI-E x16 expansion cards

PCI Express x1 slot x1 Supports PCI-E x1 expansion cards

Slots

PCI slot x2 Supports PCI expansion cards

Floppy connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each connector supports 2 IDE device

SATA Connector x6 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilities

On Board

Connector

Front Audio Connector x1 Supports front panel audio function

A740G M2+

3

SPEC

CD-in Connector x1 Supports CD audio-in function

S/PDIF out connector x1 Supports digital audio out function

CPU Fan header x1 CPU Fan power supply (with Smart Fan function)

System Fan header x1 System Fan Power supply

CMOS clear header x1 Restore CMOS data to factory default

USB connector x3 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Serial port Connector x1 Connects to RS-232 Port

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

DVI port x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connec t to DV I-D monitor

Connect to D-SUB monitor

Connect to RJ-45 ethernet cable

Connect to USB devices

Provide Audio-In/O ut and microphone connection

Board Size

215 mm(W) x 244 mm(L)

Special

Features

RAID 0 / 1 / 1+0 support

OS S u

pp

or

t

Windows XP / VISTA

Biostar Reserves the right to add or remove support

for any OS With or without notice.

1.4 R

EAR PANEL CONNECTORS

PS/2

Mouse

PS/2

Keyboard

USBX2USBX2

LAN

VGA

Line In/

Surround

Line Out

Mi c In 1/

Bass/ Center

DVI-D

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

JKBMS1

JUSB1

JUSBLAN1

JAUDIOF1

Codec

JCDIN1

Sup e r I/ O

JCOM1

JUSB4

JUSB3 JUSB2

JSFAN1

J PANE L1

SATA3

SATA 4

SATA2

SATA1

FDD1

IDE 1

JATXPWR1

JCFAN1

Socket AM2+

AMD

740G

LAN

PCI1

PCI2

PEX1_1

PEX16_1

JSPD IF_ O U T1

AMD

SB700

JC MO S1

JATXPWR2

VGA

DI MMA1

DI MMB1

BI OS

DVI

JAUDIO1

JPRNT1

JU SBV 2

JU S BV1

SATA5 SATA6

BAT TE RY

DI MMA2

DI MMB2

Not e: represents the 1■

st

pin.

A740G M2+

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only

in the correct orientation.

Motherboard Manual

6

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN1. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU

transition, you may encounter the situation that the new system fail ed to boot while using new

AM2+ CPUs. In this case, please i nstall one standar d AM2 CPU to boot your system, and

update the latest BIOS from our website for AM2+ CPUs support.

A740G M2+

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

JCFAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3

FAN RPM rate

sense

1

4

4 Smart Fan

Control (By Fan)

JSFAN1: System Fan Header

Assignment

1 Ground

2 +12V

13

3 FAN RPM rate

sense

Note:

The JCFAN1 supports 4-pin head connector. The JSFAN1 supports 3-pin head

connector. When connecti ng with wires onto connectors, please note that the r ed wire is

the positi ve and should be connected to pin#2, and the black wire is Ground and should

be connected to GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMMB1

DIMMA1

DIMMB2

DIMMA2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

A740G M2+

9

B. Memory Capacity

DIMM Socket

Location

DDR2 Module

To tal Memo r y

Size

DIMMA1 256MB/512MB/1GB/2GB

DIMMB1 256MB/512MB/1GB/2GB

DIMMA2 256MB/512MB/1GB/2GB

DIMMB2 256MB/512MB/1GB/2GB

Max is 8GB.

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module

must meet the following requirements:

Install memory module of the same density in pairs, shown in the following

table.

Dual Channel Status

DIMMA1

DIMMB1

DIMMA2

DIMMB2

Enabled O O X X

Enabled X X O O

Enabled O O O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or

x16)

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Di sk C onnector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cable.

133

234

ID E1: Hard Disk C onne ctor

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connectors can connect a master and a slave drive, so you can

connect up to two hard disk drives.

21

3940

A740G M2+

11

PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

PEX1_1: PCI-Express x1 Slot

- PCI-Express 1.0a compliant.

- Data transfer bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5GB/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX1_1

PEX16_1

PCI1~PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

Motherboard Manual

12

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 HOW TO SET UP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SET T ING S

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and

speaker connection. It allows user to connect the PC case’s front panel switch

functions.

1

8

16

PWR_LED

On/Off

RST

HLED

SPK

++

+

9

-

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

A740G M2+

13

J ATXPW R1 : ATX P o we r S ou rce C onne ct o r

This connector allows user to connect 24-pin power connector on the ATX

power supply.

1

12

13

24

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

J ATXPW R2 : ATX P o we r S ou rce C onne ct o r

By connecting this connector, it will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

12

34

4 Ground

Motherboard Manual

14

JUSB2/JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 NC

19

210

JUSB4

JUSB3 JUSB2

10 Key

SATA1~SATA6: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface,

it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

147

SATA5 SATA6

SATA3 SATA4

SATA1 SATA2

7 Ground

A740G M2+

15

JSPDIF_O UT1: Digi tal Au di o-ou t C onne ctor

This connector allows user to connect the PCI bracket SPDIF output header.

Assignment

1 +5V

2 SPDIF_OUT

13

3 Ground

JAUDIO F1: Front Panel Audio Heade r

This header allows user to connect the front audio output cable with the PC front

panel. This header allows only HD audio front panel connector; AC’97 connector

is not acceptable.

Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

1

9

2

10

10 Jack Sense

Motherboard Manual

16

JCDIN1: CD-RO M Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,

like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment

1 Left Channel

Input

2 Ground

3 Ground

1

4

4 Right Channel

Input

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting

and the CMOS data, please carefully follow the procedures to avoid damaging

the motherboard.

13

Pin 1-2 Close:

Normal Operation

(default).

13

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

A740G M2+

17

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

125

2

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6

3 Data 0 16 Ground

4 -Error 17 Data 7

5 Data 1 18 Ground

6 -Init 19 -ACK

7 Data 2 20 Ground

8 -Scltin 21 Busy

9 Data 3 22 Ground

10 Ground 23 PE

11 Data 4 24 Ground

12 Ground 25 SCLT

13 Data 5 26 Key

JCO M1: Se rial port C onnector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Assignment

1 Carrier detect

2 Received data

3 Transmitted data

4 Data terminal ready

5 Signal ground

6 Data set ready

7 Request to send

8 Clear to send

9 Ring indicator

19

210

10 NC

Motherboard Manual

18

J USB V1 /J USB V 2: Po we r So urce Hea de rs f o r USB P o r ts

Pin 1-2 Close:

JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.

JUSBV2: +5V for USB ports at front panel (JUSB2/JUSB3/JUSB4).

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at JUSB1/JUSBLAN1.

JUSBV2: +5V STB for USB ports at front panel (JUSB2/JUSB3/JUSB4).

13

1

3

Pin 1-2 close

13

1

3

JUSBV2

JUSBV1

13

1

3

Pin 2-3 close

Page is loading ...

Biostar A740G M2+ User manual

Biostar A740G M2+ User manual

Related papers

Other documents