1
HOBIE CAT 16
HOBIE CAT EUROPE
ZI Toulon Est, BP 250
83078 Toulon cedex 9, France
Tel : +33 (0)494 08 78 78 - Fax : +33 (0)494 08 13 99
Email : [email protected] - http://www.hobie-cat.net
Photo Pierrick Contin Last Update : January 2008
ASSEMBLY MANUAL
HOBIE CAT 16
Easy, Classic, Club & Race
2
HOBIE CAT 16
TABLE OF CONTENT
Part description....................................2-3
Hull assembly .........................................4
Trampoline..............................................5
Rudder assembly....................................6
Tiller crossbar & extension .....................6
Gudgeon bushings..................................7
Mast preparation.....................................8
Stepping the mast...................................9
Shrouds & trapeze................................10
Mainsail traveller...................................11
Mainsail.................................................12
Gooseneck & boom (except Race).......13
Boom & cunningham (Race only).........14
Mainsheet system.................................15
Jib....................................................16-17
Race jib halyard / Righting....................18
Jib furling assembly (option).................19
Spinnaker kit classic.............................20
Spinnaker kit trumpet soft.....................21
Before sailing........................................22
Safety advices ......................................23
Tools required
• One pair of pliers
• One rubber mallet
• 1 flat screwdriver
• 2 wrenches #17 and #10
•
1 driller with a #10 auger
It is recommended to be two people to assemble
your Hobie Cat.
Liste des Pièces
PART DESCRIPTION
Hulls (2)
Front crossbar
Rear crossbar
Side bars (2)
Mast (with mast step link)
Boom (except HC16 Easy)
Trampoline
Wire bag
Rig bag
Rope bag
Rudder assemblies (2)
Tiller crossbar
Tiller extension
Mainsail + battens (7)
Jib
Spinnaker kit (option)
CAUTION—DANGER
ALUMINIUM MAST - WATCH FOR
OVERHEAD ELECTRIC WIRES
Part description
3
HOBIE CAT 16
Part description
HC16 Ropes
1. Main halyard rope
2. Jib sheet
3. Righting line
4. Jib halyard rope
5. Tack line
6. Trampoline side line
7. Trampoline rear line
Wires and rig (photo1)
1. 2 Stay adjusters + toggles
2. Stay adjuster + 2 shackles
3. Additional stay adjuster (for 16 Race)
4. 4 Pylon screws + 4 Pylon nuts
5. Tiller connection kit (except 16 Race)
6. 2 Pins
7. 2 jib sheet blocks + shackle
8. Teflon washer
9. 4 Cutter pins
10. 2 Plugs + washers
11. Gooseneck
12. CCT LE Traveller (SSI for 16 Race)
13. Mainsheet system (mounted)
Trapeze (Photo 2)
1. 4 Trapeze handles (2 for Easy & Classic models)
2. 4 adjusting rope locks (2 for Easy & Classic models)
3. 2 shackles
4. 2 Trapeze shock cords (1 for Easy & Classic models)
5. 2 trapeze lines
Wires (Photo 3)
1. Big jib halyard blocks
2. Small jib halyard block
3. 2 sets of trapeze (1 for Easy & Classic models)
4. 2 shrouds
5. Forestay + pigtail + 8 mm shackle
1
3
2
4
HOBIE CAT 16
Insert the sidebars in their slots on the front crossbar. The flared portion
of the sidebar track must be forward and facing inward. Fit in the rear
crossbar onto the rear of the hulls and on the other end of each sidebar.
Hull assembly
Position the hulls parallel (2 meters apart) and check the left from the right hull (anti-skid on the deck
towards the outside). Start each corner casting onto the pylon just to get them together. Use the soft mallet.
1
2
Once the frame is assembled and fitted onto the hulls, drive each corner
casting down onto the pylon until the bolt holes line up. Strike the casting
directly over the pylon only. Use the soft mallet only.
3
Once the frame is definitely adjusted, we strongly recommend to redrill
each bolt passage with an auger of 10 in order to ease the fitting of the
bolts (drill alternatively each side of the pylon).
4
Install the four pylon bolts and nuts, with the nuts inboard.Tighten
securely, but do not over-torque.
TIP : do not hesitate to file off the top of the pylons. This willavoid
gripping and jamming when you fit the frame.
5
5
HOBIE CAT 16
Trampoline
Tie each aft lacing line to the aft corner casting as follows : Startwith
an 8 knot at one end of the line which you will block into the inferior
hole of the rear casting (behind the crossbar fitting). Then, pass the line
through the grommet on the side of the trampoline (from underneath),
then in the rear trampoline strip (from above). After 3 or 4 laces,
temporarily tie it at the aft end. Repeat the same operation on the other
side. NB : Make sure you passe the line above the crossbar binding nut to
avoid friction during sailing.
Insert trampoline half into the flared sidebar track so that the
grommets are running down the center and across the back. Posi-
tion the forward edge even with the forward crossbar. Insert the forward
edge of the trampoline into the front cross bar track adjacent to the
corner casting and slide it all the way to the center. Repeat this
operation for the opposite side. Install the aft lacing strip by feeding the
larger bead into the track in the aft crossbar. Make sure it is centered.
NB : The hiking straps should be on top.
1
2
Tie the center lacing line. Start with a bowline knot. Lace the line back
and forth taking up slack as you go. When lacing go through the
grommets over/under.
3
Stop the central lacing by a triangle. Use the central grommet on the
rear trampoline stripe. Make a key at the end. 4
Temporarily tie off the line at the aft end, then remove slack again by
working it out front to back. Lace the two aft lines simultaneously in
the same manner.
5
NB : As the boat is used, it will be necessary to
periodically retighten the lines.
6
HOBIE CAT 16 Rudder Assembly
RUDDER ASSEMBLY
Identify the right rudder assembly (green sticker)
and the left one (red sticker). They must not be
reversed. Slip the rudder pin down through the
casting and gudgeons. Insert the split pin in the
hole of the rudder pin so that it prevents it from
falling down. Do the same thing on the opposite
side.Make sure that the plastic cam has the nose
up as indicated on the drawing.
TILLER SYSTEM
Attach the tiller crossbar (1) to
the Rudder arm (2). Pay attention
to the left and right side. Insert
the screw as shown on the photo.
Repeat the same operation on
the opposite side.
1
Tiller crossbar and extension (Easy, Classic & Club models)
2
1
2
7
HOBIE CAT 16
Rudder Assembly
Attach the stick by slipping the
pinthrough the violin screw in
themiddle of the tiller crossbar.
The two rudder blades must be parallel or
slightly turned inside (3-4 mm). To do this it is
necessary to adjust the length of the tiller
crossbar. The screw under the tiller crossbar
allows for this adjustment. Unscrew it and you
can move the bar inside or outside. Once the
rudder blades are well trimmed, do not forget to
retighten the screw.
3
4
Tiller crossbar (Race model)
Tiller crossbar
Rudder arm
Tiller extension (all models)
8
HOBIE CAT 16
Attach the main halyard rope to the black cleat and then thread it through
the shackle of the halyard cable and secure it back to the black cleat.
Take the wire sets and install them along the
mast as shown on the drawing below :
- helm's trapeze (2)
- crew's trapeze (3)
- shroud (4)
- forestay + pigtail (5)
- shroud
- crew's trapeze
- helm's trapeze
Use the schackle to fix the wires to the mast
tang (1) insuring that :
- the forestay is between the two shrouds
- and that the trapezes are slipped around the
shackle pin apart from the mast tang.
Attach the main halyard rope to the main
halyard wire (falling from the mast head) with a bowline
knot. Set the halyard wire and rope alongside the mast.
Préparation of the mast
Attach the big block to
the pigtail with a shackle.
Hook the halyard to the
small block with a
bowline block. Slip it into
the lower sheave of the
big block then back to
the sheave of the samll
block and then in the
upper heave of the big
block. (see the drawing).
WIRES
1
2
Take the small block down to the bottom of the
mast. Thread the jib halyard around the cheek
block at the base of the mast, through the jib
downhaul block and around the cleat as shown.
3
4
5
9
HOBIE CAT 16
Place the mast pivot bearing in
the mast step cup. Install the
mast step link following the
instructions supplied with the kit.
Stepping the mast
ATTENTION - DANGER ALUMINIUM MAST -
When stepping the mast or launching the boat watch for overhead electric wires.
Shock or even death could result if the mast comes
in contact with overhead electric wires.
Take the briddle wires and
attach the opposite ends to the
shackle on the bottom of the
forestay adjuster.
1 2
3
4
Check that the bolts of the shroud anchor bars are well tightened.
Attach the shroud stay adjuster to the anchor bolts on each hull
with the clevis pins and lock rings provided.
lay the mast on top of the frame with the
mast head aft. Position the mast foot in
front of the step link body in order to insert
the pin through.
Attach the shrouds to the top holes of the
adjusters. Make sure that the shrouds are not
crossed at the mast tang. Put the shroud
covers over the adjusters. The mast is ready
for stepping.
5
10
HOBIE CAT 16 Stepping the mast
Shrouds
We recommend that you have
someone assist you. As you begin
to raise the mast the link will
rotate upward. Stand on the rear
crossbar and raise the mast to
your shoulder. At this point,
insure that the shrouds are clear
of the rudders and rear corner
castings. An assistant is
recommended. Walk forward
raising the mast as you go. At the
full upright position, lean the mast
forward against the shrouds and
have an assistant attach the
forestay (upper hole).
NB : Later adjustment may be
necessary.
Once the mast is upright, take the
pin off the mast step link. Attach
one of the shroud to the four or fifth hole of the stay adjuster. Have someone pulling down on the
trapeze in order to relieve the shroud. Do the same operation on the opposite side. Caution : it is
necessary to have the same tension on both sides. Then put the shrouds covers completely over the
stay adjusters.
Trapeze
Assemble the trapeze adjustment components as shown
in the illustration. The shock cord should passe beneath
the trampoline frame from the port trapeze line to the
starboard line
1
2
11
HOBIE CAT 16
Main traveller car
Take the traveller car CCT and
dismount it out by removing the pin
and the split ring. Slide the bearing
cylinger out by pressing the end of
the plastic part.
Take the cylinder out of the upper
part.
Split the plastic slide in two parts
and insert each one in the track of
the rear crossbar.Slide them one
over the other until they fit
together.
Reassemble the traveller car in a
reverse manner, i.e. : fit in the
upper part, slide the cylinder and
place the pin and the split ring.
1
CCT traveller (modèles Classic, Easy et Club)
SSI Traveller (Race model)
An SSI main traveller is mounted on the rear
crossbar of the Hobie Cat 16 Race.
To replace this traveller, take the inox plate off. This
will allow the traveller car to get out of the crossbar.
5
1 2
3 4
5
Easy model mounted Classic/Club model mounted
12
HOBIE CAT 16 Main Sail
Unfold the mainsail on the trampoline and insert the battens starting from the top of the sail.
1
How to fix the « Race » batten end caps
Insert the batten tie in one of the hole of the batten end cap, feed it into the opposite
grommet of the batten pocket, then into the second hole of the batten end cap, then
back in the first grommet and secure it with a knot into the V groove. Batten tension
can be varied to suit personal preference or sailing conditions.
2
How to fix the standard batten end caps (Classic, Club & Easy models)
3
The battens should be stiff. It may be necessary to make
adjustements an re-tighten them periodically after sailing
Before hoisting the sail, place your Hobie Cat directly into the wind
Take the halyard rope and the halyard wire which are attached
together on the mast and pull them apart. Pull on the halyard rope to
hoist a bit the halyard wire
4
Feed the luff into the opening in
the mast track and attach the
halyard shackle to head of the
sail. Continue pulling the halyard
and feeding the sail until it
reaches the top. When the sail is
all the way up, pull the halyard
forward sufficient for the stop
sleeve to clear the halyard hook.
5
Once the sleeve is past the hook position, pull
the halyard so that the sleeve will engage
the hook when you release tension.
6
13
HOBIE CAT 16
Hobie Cat Classic & Club—Installation of the boom
Take the boom Feed the foot of the sail into the track opening in
the forward end of the boom. Fix the boom to the gooseneck. Lead
the outhaul (already tied to the mainsail clew) around the boome
cap, through the block hanger and through the outhaul jam cleat.
Tie a figure eight knot in the end of the line.
Gooseneck and boom (Easy, Classic & Club models)
Hobie Cat 16 Easy—fixation of the tack point
This model has no boom. To fix the tack point attach the supplied tack line in the grommet at the tack point of
the main sail using a bow line knot, lead the line down to and around the black cleat , then up through the
grommet and down again around the cleat. Secure the line around the cleat.
1
Hobie Cat Classic & Club—installation of the gooseneck
Take the gooseneck and fix it to the groomet of the sail (at the clew). The sheave is facing down. Feed
the gooseneck slider in the opening of the mast and pull it down in the gorge.
NB : in order to check that it is secured, untie the halyard rope and pull the sail somewhat down. In
order to avoid crossing the halyard rope with the wires, it is recommended to route the halyard from the
front to the starboard side and around behind the starboard shroud and trapeze wires. Secure it to the
white mast cleat at the bottom of the mast and stow the excess line.
2
3
Hobie Cat Classic & Club—Installation of the downhall line
Tie the downhaul line onto the cleat with a palstek (check that the
cleat is well fixed) lead it into the gooseneck sheave, down to the
cleat and fix it. This allows to tension the luff of the sail.
4
14
HOBIE CAT 16 Boom & Cunningham (Race)
Hobie Cat 16 Race boom
Install the gooseneck and the boom in the same way as for Classic et Club models. The difference is that the
« race » gooseneck has no sheave. The boom is specially equipped with a cleat and pulley.
Cunningham
Fix the upper triple block to the lowest gooseneck thimble using the supplied 4 mm shackle.The cunningham
line is threaded in the same way as the mainheet system (6:1 purchase). No other system is authorized by the
Hobie Cat class rules.
1
2
15
HOBIE CAT 16
Mainsheet system
The mainsheet system is already mounted when delivered with
your boat.
We indicate hereunder the way to thread it, in case that you need
to change the line.
Shackle the boom block to the boom block hanger. Shackle the
ratchet block to the traveller car (the jam cleat facing inboard).
• Tie a eight figure knot at the end of the mainsheet and feed
it through the upper strap of the ratchet block and then,
• up into the first sheave of the boom block from front to rear
• down into the first sheave of the ratchet block from front to
rear
• up into the second sheave of the boom block from rear to
front
• down into the second sheave of the ratchet block from front
to rear
• up into the third sheave of the boom block from rear to front
• down into the third sheave of the ratchet block from rear to front
Feed it then into the lower strap of the cam cleat of
the ratchet block. Run the free end of the
mainsheet through the cam cleat of the aft
crossbar, through the traveller car from inside to
outside, and the dead eye behind the cam cleat. Tie
a figure eight knot to secure the line.
Sheet in and out to see if all is well mounted.
1
2
16
HOBIE CAT 16
Lead the jib sheet to one of the
clew blocks and back through
the second hole of the Trentec
traveller car, then back to the
jib block on the front crossbar,
leading it first through the
sheaves and then under the
strap of the cam cleat. Repeat
the operation on the
opposite side in a reverse
manner : feed the jib sheet
under the strap
of the opposite jib block on the front crossbar, then between the
sheaves, then through the 2nd hole of the Trentec traveller car
(the one towards the inside) from outside to inside, and then back to the
first hole of the traveller from inside to outside. Secure the end of the
line with a knot.
NB : to lead the jib sheet from one jib block to the other, be careful to
stay inside of the boat. Never lead the rope behind the mast.
Jib assembly
Unfold the jib on the trampoline and inser’t the battens in their pockets following the instructions below :
1
1 2 3
4 5 6
1. Make sure the line is correctly inserted in the hole of the strap.
2. Insert the batten in its pocket
3. Bend the strap in half and insert the end in the batten pocket.
4. Introduce the batten pusher in the batten pocket, making sure the line is positioned in the « V » of the
batten pusher.
5. Push the batten pusher in the batten pocket until the desired tension is obtained.
6. Simply pull on the line to take the batten out of its pocket.
Take the jib sheet. Thread one
end in the external hole of the
jib traveler car and secure it
with a knot. The knot is outside
the frame.
2 3
17
HOBIE CAT 16
Jib Assembly
Shackle the jib tack
to the 4th or 5th hole
of the forestay adjuster
(depending on the sailing
conditions).
4
Take the jib block at
the bottom of the mast
and fix it to the head of the
jib. The small line on the
jib is a further security.
Secure the plastic hank to the
forestay by twisting it 90° onto
the wire and hoist the jib. Secure
the jib halyard on the cleat at the
bottom of the mast and stow the
excess line on the trampoline
pocket.
5
6
Shackle the small jib blocks to the jib clew plate. Check that the ropes
do not cross each other. First, fix the shackle in the middle hole of the
jib clew plate. This can be changed according to sailing conditions.
7
Without furler
With furler (option)
18
HOBIE CAT 16
The Jib halyard adjustment system is installed as serial
equipment on the Hobie Cat 16 Race.
Just thread the jib halyard rope as indicated on the picture
and stop it into the white cleat.
Race jib halyard / Righting line
RIGHTING LINE
Attach the righting line to one of the front pylon with a figure eight knot. Tie the other end to the opposite pylon.
The line should be lead under the trampoline through the center lacing.
2
1
19
HOBIE CAT 16
Classic spinnaker kit (option)
20
HOBIE CAT 16 Trumpet spinnaker kit (option)
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
