Centrometal CAS-S-B-BS-vinyl Mounting instructions

Brand: Centrometal

Model: CAS-S-B-BS-vinyl

Type: Mounting instructions

HEATING TECHNIQUE

TUMCAS1-04/2010-eng

CAS; -S; -B; -BS

Centrometal d.o.o. - Glavna 12, 40306 Macinec, Croatia, tel: +385 40 372 600, fax: +385 40 372 611

for installation of thermal insulation and

jacket for accumulation tank

TECHNICAL MANUAL

Install the accumulation tank on the horizontal surface and insert the temperature sensors in

the tube on the tank (picture 1.)

2Mounting of the thermal insulation CAS, CAS-B, CAS-S i CAS-BS

picture 1.

picture 2.

direction

junction

Mounting of the thermal insulation and jacket on the CAS, CAS-B, CAS-S

and CAS-BS tanks

Procedure for the assembling of the thermal insulation of the accumulation tank CAS, CAS-B, CAS-

S and CAS-BS is described in the extension of this manual. On the picture is shown CAS-S tank:

tube 3/8''

temp. sensor

tube for the

temp. sensor

possible opening for

temp. sensor

sponge with the

artificial leather

possible opening for heat exchanger

connection is used for accumulation tank

CAS-S i CAS-BS

opening for

thermometers

tube for

thermometer 1/2''

In case of afterwards mounting of the sensors it is not necessary to remove the sponge then

with the knife cut the jacket on the necessary places for the temp. sensors.

When You unpacked the sponge with the artificial leather, with the zipper connect the two part

of sponge (it is connected from top to bottom) (picture 2).

picture 4.picture 3. lid made

of sponge

On the connections placed the rosette and on the plastic lid glue the stickers on the opening for

the connections (picture 6. and picture 7.)

On the top, over the connections of the tank, put the lid made of sponge (picture 4.)

Tehničko uputstvo CentroMini 3

thermometer

picture 5. picture 6.

picture 7.

Mounting of the thermal insulation CAS, CAS-B, CAS-S i CAS-BS

Mounting of the thermal insulation and jacket on the CAS, CAS-B, CAS-S

and CAS-BS tanks

Afterwards adjust the sponge on connection (6/4"), then wrap the sponge around the tank,

push the sponge with the hand to fit the tank and connect with the zipper (it is connected from

top to bottom) (picture 3.)

On the top of the tank, over the connections and edges of the sponge, adjust the plastic lid of

the tank and screw the thermometers in the tube for thermometer(picture 4. and picture 7.)

plastic lid

of the tank

red

rosette

black

rosette

red

rosette

black

rosette

black

rosette

blue

rosette

black

rosette

introducer

connection

(red rosette)

connection

(red rosette)

knife

introducer

hot sanitary water

(red sticker)

recirculation

(red sticker)

cold sanitary

water (blue sticker)

lid for CAS and CAS-S lid for CAS-B and CAS-BS

blue

rosette

If the jacket is in cold room, it is necessary to keep the jacket on room temperature for 24

hours to be prepared for mounting.

By lower room temperature the material of the jacket changes his properties, so jacket

must be mounted on room temperature. It is recommended to mount the jacket on ca.

20°C, if not, the mounting will be hard.

The jacket is delivered bended, so it can have some anomaly in looks. These anomalies will

disappear in 48 hours from mounting.

The tank is ready for the installation on the central heating system (CAS, CAS-S, CAS-B i CAS-

BS) (CAS-B i CAS-BS) and sanitary water circuit .

HEATING TECHNIQUE

www.centrometal.hr

e-mail: [email protected]

Centrometal d.o.o. Glavna 12, 40306 Macinec, Croatia

central tel: +385 40 372 600, fax: +385 40 372 611

service tel: +385 40 372 622, fax: +385 40 372 621

IMPORTANT!

Centrometal d.o.o. shall not be responsible for possible incorrect data caused by printing errors or error made in transcription and all

figures and diagrams are for explanatory purposes only and relevant adjustment have to be made at the spot. In any case, it

reserves the right to modify its products as deemed to be required and useful without any prior notification.

Centrometal CAS-S-B-BS-vinyl Mounting instructions

Centrometal CAS-S-B-BS-vinyl Mounting instructions

Centrometal CAS-S-B-BS-vinyl Mounting instructions

Related papers

Other documents