Metal Garden Shed
OWNER'S MANUAL
Instructions for Assembly
Requires two people and takes
1-1.5 hours for lnstallation.
Quick & Easy Assembly
Ridge Reinforced Walls
Wood Storage
9820005
at least
Overall Size: L270 x W105 x H130/158 cm
Overall Size: L8.8 x W3.4 x H4.3/5.2 Feet
BEFORE YOU START
Owner's Manual
Prior to installation, it is important that you contact your local government authority to
determine if building approval is required. Study and understand this owner's manual.
Important information and helpful tips will make your construction easier and more
enjoyable.
Assembly instructions
Instructions are supplied in this manual and contain all appropriate information for your
building model. Review all instructions before you begin. During assembly, follow the
step sequence carefully for correct results .Please be aware: this unit takes two people
about one full day to complete.
Parts
Check to be sure that you have all the necessary parts for the building.
Separate contents of the carton by the part number while reviewing parts list.
Familiarize
yourself
with
the
hardware
and
fasteners
for
easier
use
during
construction. These are packaged within the carton. Note that extra fasteners have been
supplied for your convenience.
TOOLS MAY REQUIRED
Use heavy duty gloves when handling steel sheets and flashing
PLAN AHEAD
Watch the weather:
Please be sure the day you select for installation is dry and calm.
DO NOT attempt to assemble your shed in windy weather
because of risk of damage to panels, or personal injury. Be careful
of wet or muddy ground.
Teamwork:
Whenever possible, two or more people should work together to
assemble the building. One person can position parts or panels
while the other is able to handle the fasteners and the tools.
3M
1/10"
1/5"
5/16"
PLAN AHEAD
Site Selection
l Avoid overhanging trees as much as possible as leaves will make regular cleaning
necessary and broken branches are a potential hazard.
l Small trees,bushes or fences nearby can be helpful,acting as a wind break.
Site Preparation
The site must be prepared so that the base of the shed is level all round and checking
with a spirit level is required.
The base can be constructed by treated timber or concrete,in order to stop the moisture
getting into the shed.The shed is not designed to be built onto lawn directly.Also the
ground will get muddy during rainy days.
If a concrete pad is made,it is important that this slopes towards the edges to prevent
water ingress.
Time must be allowed for any concrete or cement to dry before building the shed on top.
Bases can also be constructed from bricks,blocks,or mounted on a concrete pad.
The bricks or blocks should be cemented onto firm and level concrete footings and the
greenhouse frame drilled and screwed to the base.
IMPORTANT NOTES:
l Find someone to help you:it is much easier with someone to hold parts,pass tools
ect.Also some steps require two people to lift structures together.This is not very
heavy work so would suit most able-bodied people.
l Allow plenty of time:rushing often causes errors and the re-doing of incorrect
assemblies.If you have never built a shed before,it can take most of a day to carefully
complete the construction.
l Have the right tools to hand.
l Safety clothing as recommended in the 'Tools' section.
l Ideally lat out the parts and check that all are present before commencing
construction.Lay on cloths or plastic sheets if there is any risk of scratching the parts.
l Tighten all nuts carefully,being sure not to miss any.Check the frame is square and
using a spirit level to check that it is upright.
sharp edges
when assembling or performing.
wear work gloves, long sleeves and eye glasses,
Pay attention to the sharp edges. Please
PART
NO.
Qty.
PART
NO.
Qty.
P1
P3
4
1
1275mm/50.19"
1035mm/40.74"
1L 1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
944mm/37.16"
1620mm/63.78"
516mm/20.31"
1R
3
4L
4R
8
9
10
11
13
14
15
1390mm/54.72"
1540mm/60.62"
876mm/34.48"
448mm/17.63"
1615mm/63.58"
1621mm/63.81"
19
20
21L
21R
22L
22R
25
26
592mm/23.3"
1623mm/63.89"
462mm/18.18"
27
28
2
1
1088mm/42.83"
1035mm/40.74"
29
1
1
C
3R
1
1
1
12
939mm/36.96"
1
1
10L
10R
1528mm/60.15"
1
1623mm/63.89"
30
5L
5R
1
1
2
31
799mm/31.45"
1
33
1
34
1264mm/49.76"
P2
1
1390mm/54.72"
P8
2
1528mm/60.15"
1308mm/51.49"
944mm/37.16"
944mm/37.16"
944mm/37.16"
516mm/20.31"
1308mm/51.49"
1528mm/60.15"
939mm/36.96"
1264mm/49.76"
PART
NO.
Qty.
P6
3
592mm/23.3"
P7
1
B6
H1&J5
F1
F2
S3
1
180
1580mm/62.2"
W1
GC
GA
2
1
1
5
230
30
L1
L2
2
2
P4
1
1035mm/40.74"
P5
1
D1
1
1263mm/49.72"
B5
1
S4
120
F3
8
1035mm/40.74"
592mm/23.3"
#8AB-18x2/13
#8-32x2/13
#8-32x2/13
3
3
W1
4R
4L
8
9
9
8
P2
20
19
21L
21R
11
11
15
14
30
26
25
P7
P6
P6
P6
GC
GC
GA
GC
GC
GC
P3
P5
P4
27
28
28
29
22L
22R
12
13
10
10
10L
10R
P8
P8
P1
P1
1L
3R
C
1R
P1
P1
5R
5L
31
31
34
33
L1
L2
D1
L2
L1
B6
B6
H1
J5
B5
Door Post of Tool Shed Installation
Base of Tool Shed Assembly
When diagonal measurements are
F1
F1
PART
NO.
Qty.
1、
equal,the frame is square.
2、The Floor Frame must be
BOTH square AND level or the
holes will not line up properly.
-7-
PART
NO.
Qty.
1L 1
1
1R
1
1
C
3R
1L
3R
C
1R
5L
5R
1
1
F1
S3
F1
F1
F1
S3
C
5L
5R
F1 8
F1
8
S3
6
Inspection
Right Side Wall Panels Installation
Corner Post 10L
P1
2
F1
S3
-8-
PART
NO.
Qty.
F1
S3
F1
S3
P8
10R
P1
F2
S3
P1
P1
PART
NO.
Qty.
1
10R
P8
2
F1
S3
F2
S3
PART
NO.
Qty.
1
10L
P1
2
F1
S3
F2
S3
F1
S3
F1
S3
P1
10L
P8
P1
P1
10R
P8
P8
10L
F1
8
S3
10
F2
2
F1
9
S3
12
F2
3
F1
10
S3
14
F2
4
Wall Panels Installation
inside
Corner Post 10R
inside
Left Side Panels Installation
Right Triangle Panel Installation
Right Side Upper Beam Installation
-9-
PART
NO.
Qty.
1
12
12
F1
S3
PART
NO.
Qty.
1
22L
1
10
22L
10
22L
10
PART
NO.
Qty.
1
22L
1
10
PART
NO.
Qty.
1
22R
1
10
F1
S3
10
22R
F1
S3
10
22R
F1
9
S3
9
F1
12
S3
12
F1
12
S3
12
Left Side Upper Beam Installation
Left Triangle Panel Installation
(Wood Storage Cabinet)
-10-
PART
NO.
Qty.
13
1
F1
S3
F1
S3
13
PART
NO.
Qty.
4L 1
1
4R
1
W1
2
3
F1
3
3
W1
4R
4L
PART
NO.
Qty.
1
1
8
9
P2
1
S3
F1
F2
S3
8
9
P2
8
9
F1
6
S3
6
F1
8
F1
6
S3
8
F2
2
Front Upper Beam
Installation
Base of Wood Storage
Cabinet Installation
Side Wall Panel Installation
Corner Post Installation
-11-
PART
NO.
Qty.
1
1
8
9
8
9
S3
F1
PART
NO.
Qty.
1
1
21L
21R
1
1
21L
21R
2
11
S3
F1
21L
11
11
21R
1
14
14
PART
NO.
Qty.
1
15
15
S3
F1
F1
4
S3
4
F1
14
S3
14
F1
4
S3
4
Right Corner Posts Installation
Front Beam,Frame and
Triangle Panels Installation
(Wood Storage Cabinet)
Triangle Panels
Fixation
-12-
PART
NO.
Qty.
PART
NO.
Qty.
1
19
1
20
F1
F1
19
20
PART
NO.
Qty.
P6
3
P7
1
P6
P6
P6
P7
S3
F1
F1
4
F1
4
F1
16
S3
16
Connection Between Tool
Shed and Wood Storage Cabinet
Connection Between Tool
Shed and Wood Storage Cabinet
Roof Panels Installation
Eaves and Plastic Ends Installation
-13-
GA
PART
NO.
Qty.
P3
1
P4
1
P5
1
P4
P3
P5
S3
F1
PART
NO.
Qty.
25&26&27
29&30
1
GC
GA
1
5
GC
GC
GC
GC
GC
27
26
28
29
28
30
25
2
28
GA
GC
S3
F1
F1
F1
PART
NO.
Qty.
2
L1
2
L2
2
31
L1
L2
31
x2
F1
F1
21
S3
21
F1
10
S3
4
F1 8
Roof Panels Installation
(Tool Storage)
Corner Connector Installation
-14-
PART
NO.
Qty.
1
33
1
34
D1
1
D1
33
34
34
33
D1
S3
F2
S3
F1
PART
NO.
Qty.
F3
34
S3
F2
33
2
B6
F1
S3
2
F2
2
PART
NO.
Qty.
F1
12
S3
14
F2
2
F3
F1
4
4
Door Panel and Door Frame Assembly
Door Assembly
Door Assembly and Fixation
Turn Opposite
-15-
PART
NO.
Qty.
H1&J5
1
B5
1
F2
B5
J5
H1
F3
PART
NO.
Qty.
F3
4
F2
2
Door of Tool shed Installation
Doorknob and Bolt Installation
Finishing
/
