Eurotech DuraVIS 3010 Owner's manual

Rev. 1.3 - May 2009 - 07-0094UM0001D

DIGITAL TECHNOLOGIES FOR A BETTER WORLD

www.eurotech.com

DURAVIS 3010

6.4’ Rugged Display

USER’S MANUAL

Note: The information in this document is subject to change without notice and should not be construed as a commitment by any EUROTECH

company. While reasonable precautions have been taken, EUROTECH assumes no responsibility for any error that may appear in this document.

All trademarks or registered trademarks remain the property of EUROTECH.

DURAVIS 3010 – User’s Manual

3

Introduction

Manual Conventions

The following conventions are used throughout this manual.

The “Mode” of the register:

Symbol / Text Definition

RW

Readable and Writable register

RO

Read only register

W

Meaning of the register when written

R

Meaning of the register when read

Hexadecimal numbering:

Hexadecimal numbers are indicated with an “h” suffix (for example: 11Ch)

Symbols and Text used in Pin-out tables:

Symbol / Text Definition

◄

Input

►

Output

◄►

Bi-Directional

▬

Passive

Module specific

Dependent on module installed

NC

Not Connected

Reserved

Use reserved to Eurotech, must remain unconnected

#

Active low signal

Warnings and Important Notices:

Within this manual you will find the following tables, please ensure that you read and understand these

as they are intended to highlight potential risks or precautions that should be taken.

Warnings:

Information to alert you to potential hazards:

Potential personal injury or damage to a system, device, or program.

Information notes:

Indicates important features or instructions that should be observed

DURAVIS 3010 – User’s Manual

4

Eurotech would like to point out that, although all the information contained herein has been carefully

verified, Eurotech does not assume any responsibility for errors that might appear in this document, or

for damage to property or persons resulting from an improper use of this manual and of the related

software. Eurotech reserves the right to change the contents and form of this document, as well as the

features and specifications of its products at any time, without notice, particularly because of

continuous upgrades.

Eurotech informs you that the information contained in this manual is continuously being updated in

line with the technical alterations and improvements made by Eurotech to the products and thus this

manual only reflects the technical status of the products at the time of printing.

Updated versions are available on the Eurotech websites: www.eurotech.com and

www.eurotechfrance.fr.

For further information, please contact:

Eurotech France

Phone: +33 (0)4 72 89 00 90

Fax: +33 (0)4 78 70 08 24

Email: sales@eurotechfrance.fr

This manual is protected by copyright.

Trademarks and registered trademarks appearing in this document are the property of their respective

owners.

Copies of all or part of this manual or translations into a different language may only be made with the

prior written consent of Eurotech.

Printing and duplication is only permissible with the express approval of

Eurotech France S.A.S.

Parc Club du Moulin à Vent

33 Avenue du Docteur Georges Levy – Bât. 33.1

69693 VENISSIEUX Cedex

FRANCE

DURAVIS 3010 – User’s Manual

5

Table of Contents

Introduction 3

Table of contents 5

Important Instructions 6

Safety Instructions 7

Chapter 1 Product Overview 9

Chapter 2 Interfaces 12

Chapter 3 Troubleshooting 15

Appendix 16

DURAVIS 3010 – User’s Manual

6

Important Instructions

We recommend that you observe the instructions contained throughout this manual when using your

CPU ATLAS Module, they are intended to give users important guidelines to lower the risk of

personal injury, electric shock, fire or damage to equipment.

Exclusion of Accident Liability Obligation

Eurotech Spa shall be exempted from the statutory accident liability obligation if the user fails to

observe the safety instructions.

Liability Limitation / Exemption from the Warranty Obligation

In the event of damage to the device caused by failure to observe the instructions in this manual and

eventually on the device (especially the safety instructions), Eurotech Spa shall not be required to

honour the warranty even during the warranty period and shall be exempted from the statutory

accident liability obligation.

DURAVIS 3010 – User’s Manual

7

Safety Instructions

Retain and follow all the operating instructions, warnings and information herein.

Observe any warning notices on the product.

In order to lower the risk of personal injury, electric shock, fire or equipment damage,

users should observe the following precautions:

General precautions

 Take notice of the indications on the labels / silk-screen images on the product

 Except where expressly specified in the documentation, users should not attempt to

repair Eurotech products.

 Do Not Expose to Direct Heat Sources: keep the product away from heat sources,

for example heaters, radiators, engine casing, etc.

 Do Not Insert Foreign Objects Into Product: never insert objects in any slot (if

present).

o Ventilation slots should remain unblocked to insure correct cooling.

o Inserting foreign objects into a card slot may result in system failure

 Installation: Always insure that the apparatus is installed using adequate supports.

When installing the product, follow the manufacturer’s instructions and use the

recommended mounting accessories.

 Ensure proper ventilation. Observe any instructions regarding air circulation

Power Cables and Accessories Safety Guidelines

 Always Use Appropriate Power Supply: only start the product using a power supply

that meets the specifications as stated on the voltage label and within the user

manual. In case of uncertainty about the required power supply, please contact the

Eurotech technical support team.

 Use Certified Power Cables.

 Position Cables With Care: avoid positioning cables where they may be crushed.

 Cleaning: before cleaning the product, disconnect it form the main power supply.

• Do not use spray detergents.

• Only use a damp cloth.

• DO NOT attempt to clean exposed electronic components (in this case only

use a air duster)

 Damage Requiring Assistance: disconnect the product from the main power supply

point and contact Eurotech technical support team whenever the following conditions

occur:

• The product suffered any form of damage.

• There is evidence of overheating.

• The product does not work normally when operating instructions are carried

out.

DURAVIS 3010 – User’s Manual

8

WEEE

The information below is issued in compliance with the regulations as set out by the 2002/96/CE

directive, subsequently superseded by 2003/108/CE, and refers electrical and electronic equipment

and the management of their waste (WEEE)

When disposing of a device, including all of its components, subassemblies and materials that are

an integral part of the product, you should consider the WEEE directive.

This symbol has been attached to the equipment or, in the case that this is not possible,

on the packaging, instruction literature and/or the guarantee sheet. By using this symbol, it

states that the device has been marketed after August 13th 2005, and implies that you

must separate all of its components when possible, and dispose of them in accordance with

local waste disposal legislations.

Because of the substances present in the equipment, an improper use or disposal of the refuse can cause damage

to human health and to the environment.

With reference to WEEE, it is compulsory not dispose of the equipment with normal urban refuse, arrangements

should be instigated for separate collection and disposal.

For more detailed information about recycling of WEEE, please contact your local waste collection

body.

In case of illicit disposal, sanctions will be levied on transgressors.

RoHS

This device, including all it components, subassemblies and the consumable materials that are an

integral part of the product, has been manufactured in compliance with the European directive

2002/95/EC known as the RoHS directive (Restrictions on the use of certain Hazardous Substances).

This directive targets the reduction of certain hazardous substances previously used in electrical and

electronic equipment (EEE).

DURAVIS 3010 – User’s Manual

9

Chapter 1 Product Overview

In the following paragraphs you will find a general description of the Eurotech Military Rugged Display

DuraVIS 3010.

For a complete list of our products please go to our web site:

www.eurotech.com

www.eurotechfrance.fr

DURAVIS 3010 – User’s Manual

10

Product definition

The Eurotech DuraVIS 3010 is a rugged flat panel 6.4 inches TFT Liquid Crystal Display. This

hardened military/avionics-grade monitor features daylight readability, lightweight aluminum chassis,

and anti-glare protective covers for impact protection and explosive decompression. Designed to meet

military GAM EG13 environmental standards (French equivalent to MIL STD), this rugged Commercial

Off the Shelf (COTS) flat panel incorporates a hardened mechanical design well suited for avionics,

vehicular, and other high reliability applications.

Specifications

Liquid Crystal

• 6.4” a-SI TFT LCD with LED Backlight

Luminance

• 850 cd/m² (nit) typical

Video Input

• VGA Video Input (Option for LVDS input on request)

Resolution

• VGA Resolution – 640 x 480 pixels

Touchscreen

• Resistive Film Analog Controller, RS-422 Interface

• WinCE / WinXP / Linux / DOS drivers

• The driver of the touchscreen panel is available on the website of DMNC Co. Ltd:

http://www.dmccoltd.com/english/download/index.asp

Buttons

• 6 Pushbuttons for Brightness adjustment, ON/OFF Backlight, colour adjustment or Key functions

Viewing angle

• -50~50° (H), -35~45° (V) at contrast ratio 10:1

Protective windows / Coatings

• Anti-reflective, ITO (optional) Hard Coatings

Backlight LED Life (MTBF):

• 50,000 Hours

Weight

• Approx. 1.36 kg (3.0 lbs)

DURAVIS 3010 – User’s Manual

11

EMI / EMC and environmental compliance

• Designed to meet GAM EG13 and MIL-STD 810 standards

Power Input

• 18 to 36 Vdc

Operating temperature

• -20°C to +60°C

Finish

• Black Anodized Finish

Cooling

• Not required (natural convection)

Physical dimensions

• 192.5 mm (W) x 136 mm (H) x 44 mm (D)

DURAVIS 3010 – User’s Manual

12

Chapter 2 Interfaces

In the following paragraphs you will find a detailed description of the interfaces of the display.

Description of the interfaces

Buttons

All buttons are managed by the CPU, using digital I/Os.

ON / OFF

BRIGHTNESS +

BRIGHTNESS

–

NOT USED

OSD

MODE

NOT USED

RIGHT

EXIT

LEFT

BACKLIGHT MODE

MENU

Backlight mode

OSD

mode

Fonction Mode

K1

K3

K5

K2

K4

K6

DURAVIS 3010 – User’s Manual

13

Modes Management

Standard mode is Backlight mode, you can enter OSD mode by using the OSD MODE button, and the

display will automatically leave this mode 10s after the last use of a button.

Function mode is only engaged by the ASCII command “A” through the RS485 link.

After that it will stay in this mode until it received “Z” through the RS485, of power off

The “S” command can check active mode, answer is “F” for function mode “N” for normal mode.

In function mode each push on button generates a character:

K1 = “1”

K2 = “2”

K3 = “3”

K4 = “4”

K5 = “5”

K6 = “6”

Serial link RS 485 parameters are

19200, parity even, 1 bit stop.

Video Input (Sub D Version)

This port is a VGA input. The connector is a standard high density 15-pins female subD type

connector.

Pin # Signal

1 RED

6 GND

11 NC

2 GREEN

7 GND

12 NC

3 BLUE

8 GND

13 HSYNC

4 NC

9 NC

14 VSYNC

5 GND

10 GND

15 NC

Power supply and Touchscreen panel (Sub D version)

This port is used to provide power supply and touchscreen panel signals.

The connector is a standard 9-pins female subD type connector.

Pin # Signal

1 RX+

4 NC

7 TX-

2 TX+

5 0V (28V)

8 RS485 B

3 RS485 A

6 RX-

9 +28V

DURAVIS 3010 – User’s Manual

14

HE308 Connector Version

This port is a rugged 22-pins HE308 type connector. It provides signals for the video input, the power

supply, the touchscreen panel and the buttons controls.

Pin # Signal

1 Vbat+

9 RED

17 N.C.

2 Vbat-

10 GREEN

18 GND

3 RS422 RX+

11 GND

19 GND

4 RS422 TX+

12 BLUE

20 RS485 A

5 RS422 TX-

13 HSYNC

21 RS485 B

6 GND

14 VSYNC

22 N.C.

7 RS422 RX-

15 N.C.

8 GND

16 N.C.

HE308 connector

DURAVIS 3010 – User’s Manual

15

Chapter 3 Troubleshooting

Technical & Sales Assistance

 If you have a technical question or if you cannot isolate a problem with your display, please

call or e-mail the Eurotech Technical Support:

email: support@eurotechfrance.fr

Phone: +33 (0)4 72 89 00 90

Fax: +33 (0)4 78 70 08 24

 If you have a sales question, please contact your local Eurotech Sales Representative or the

Regional Sales Office for your area.

 Additional and latest information is available at Eurotech website, located at:

http://www.eurotechfrance.fr/

Returning For Service

Before returning any of Eurotech's products, you must contact the Eurotech Technical Support

sending an e-mail (support@eurotechfrance.fr) with the model number, serial number, short fault

description and contact details to obtain a Returned Material Authorization (RMA) number.

Note. You must have the RMA number in order to return any product for any reason!

Pack the system in anti-static material and ship it in a sturdy container with enough packing material to

adequately cushion it.

Warning! Any product returned to Eurotech improperly packed will immediately void the

warranty for that particular product!

Technical & Sales Assistance

If you have a technical question, please contact the Eurotech Customer Support Service

support@eurotechfrance.fr

If you have a sales question, please contact your local Eurotech Sales Representative or the Regional

Sales Office for your area.

Additional and latest information is available at Eurotech website at:

www.eurotechfrance.fr

DURAVIS 3010 – User’s Manual

16

Appendix

Electrical and Environmental Specifications

The following section provides tables showing the electrical, mechanical and environmental

specifications for the 6.5’ rugged display.

Operating Characteristics

Electrical Operating Characteristics

The board is powered via 9-pins suB female connectors.

• Vin = +18 to +36V dc

Operating Temperature Range

 Operating temperature: -20°C to +60°C

 Relative humidity: 5 to 90 % without condensation.

Mechanical Dimensions

Physical dimensions

• 192.5 mm (W) x 136 mm (H) x 44 mm (D)

Weight

• Approx. 1.44 kg

AMERICAS

North America

EUROTECH USA

US toll free +1 800.541.2003

tel. +1 301.490.4007

fax +1 301.490.4582

e-mail: sales-us@eurotech.com

e-mail: support-us@eurotech.com

www.eurotech-inc.com

PARVUS CORPORATION

US toll-free +1 800.483.3152

tel. +1 801.483.1533

fax +1 801.483.1523

e-mail: sales@parvus.com

e-mail: tsupport@parvus.com

www.parvus.com

EUROPE

Central & Southern Europe

EUROTECH Italy

tel. +39 0433.485.411

fax +39 0433.485.499

e-mail: sales-it@eurotech.com

e-mail: support-it@eurotech.com

www.eurotech.com

Western Europe

EUROTECH UK

tel. +44 (0) 1223.403410

fax +44 (0) 1223.410457

e-mail: sales-uk@eurotech.com

e-mail: support-uk@eurotech.com

www.eurotech.com

EUROTECH France

tel. +33 04.72.89.00.90

fax +33 04.78.70.08.24

e-mail: sales-f[email protected]om

e-mail: support-fr@eurotech.com

www.eurotech.com

Northern & Eastern Europe

EUROTECH Finland

tel. +358 9.477.888.0

fax +358 9.477.888.99

e-mail: sales-fi@eurotech.com

e-mail: support-fi@eurotech.com

www.eurotech.com

ASIA

Japan

ADVANET

tel. +81 86.245.2861

fax +81 86.245.2860

e-mail: sales@advanet.co.jp

www.advanet.co.jp

China

VANTRON

tel. + 86 28.85.12.39.30

fax +86 28.85.12.39.35

e-mail: sales@vantrontech.com.cn

e-mail: support-cn@eurotech.com

www.vantrontech.com .cn

Eurotech Group Worldwide Presence

www.eurotech.com

Eurotech DuraVIS 3010 Owner's manual

Eurotech DuraVIS 3010 Owner's manual

Related papers

Other documents