Nature Power 24208 Operating instructions

Brand: Nature Power

Model: 24208

Type: Operating instructions

Nature Power 24208 is a ventilation fan powered by a high efficiency polycrystalline solar panel, designed to be installed into any building that requires ventilation, with no running costs or pollution. With a 9V 10W polycrystalline solar panel, 18-inch fan blade, brushless motor, and adjustable mounting brackets, it can deliver an airflow of 950CFM at a speed of 1500RPM. The fan is suitable for various locations, including basements or gables, and can be installed in wooden or concrete walls.

SAVE THESE INSTRUCTIONS

WARNING: ead and understand all instructions, warnings, and cautions before using this

product. Failure to follow the instructions, warnings, and cautions ay result in serious personal inury

andor property daage.

Item # 220

Page 1 of 8





V1.

Thank you for purchasing a Nature Power product!

Please read this manual thoroughly and keep the manual and your purchase receipt in

a safe place for future reference.

Failure to follow the safety rules and other basic safety precautions may result in

serious personal injury.

If you are missing any parts, or receive damaged parts please call Customer Service at

1-800-588-0590.

Intended se

Technical Specifications

Property Specification

Speed

150P

Fan Sie 1 1   910 in

Solar Panel Type

 Polycrystalline

Fan lade 1 in

Weight N

15.8 lbs

ir Flow

95C150CF

Fan otor

rushless C

Page  of 8

The able ount Fan is designed to be installed into any building that requires

ventilation. Powered by high efficiency polycrystalline solar panel, no running costs,

no pollution.

Important Safety Information

The warnings, cautions, and instructions in this manual cannot cover all possible conditions or

situations that could occur. ercise common sense and caution when using this product.

lways be aware of the environment and ensure that the product is used in a safe and

responsible manner.

o NT use to ehaust haardous material, dust, or combustible vapors.

uring installation, always wear appropriate safety glasses, gloves, hard hats, restraints, and

other safety euipment to avoid injury. arning lways wear durable work gloves while

handling the unit.

bserve all applicable building and electrical codes

Inspect for hidden utilities before cutting or drilling. o NT damage electrical wiring or other

hidden utilities when cutting or drilling.

ead and understand all instructions. Failure to follow all instructions may result in serious

injury or property damage.

o not allow persons to use the product until they have read this manual and have developed a

thorough understanding of how it works.

o not modify this product in any way. nauthoried modification may impair the function and

or safety and could affect the life of the product. There are specific applications for which the

product was designed.

se the right tool for the job.  NT attempt to force small euipment to do the work of larger

industrial euipment. There are certain applications for which this product was designed. It will

do the job better and more safely at the capacity for which it was intended.  NT use this

product for a purpose for which it was not intended.

Industrial or commercial applications must follow S reuirements.

Page  of 8

Assembly

Fan be installed

in the wooden

frame

The fans mounting brackets on sliding rails are adjustable, oosen screws to set the needed position

of brackets, Fi them with 8bolts. Carefully adjust the brackets to the desired position and affi to

frame. It may be necessary to build additional supports to fit the fan into the desired position.

Part 1 Fiing the Fan

Typical installations include placement in a basement or gable. Instructions are shown below for these

two sample installations. s the fan may be installed in any number of locations, these instructions are

provided as a general guide. If you are unsure of how to install in your particular location, consult with

a skilled handyman or contractor.

Safety precautions should be taken at all times.

Choose a location for installing the fan.

Place the fan behind an eisting gable wall louver or install a new louver and intake. The fan should

be approimately   mm to  10 mm away from the eterior louver.

Page  of 8

Two kinds of bolts are provided in pacakage

For concrete wall

For wooden wall

Part  ounting the Solar Panel

Choose the optimal location for the solar panel.

The fan is powered

by the solar panel and will run only when the solar panel is receiving adeuate

sunlight. For this reason, the optimal location for the solar panel will be where it can receive the

maimum amount of sunlight during the day, with the little or no shade.

The solar panel is secured with all four  screws in the package. pen the solar panel by loosening

the screws on one side, to remove the brackets concealed inside

nce the solar panel is installed, run the cable inside through the louvre. Ensure there is a dip in the

wire on the outside as shown below. This will allow any condensation and rain to drip off the wire

and not enter the structure.

Page 5 of 8

Part  onnecting Solar Panel to the Fan

onnect the solar panel cable to the fan connection cable. Expose the solar panel to sunlight. se a

ultieter to verify and ar the positive and negative wires.

olar panels angle braces

For concrete wall

For wooden wall

IN II S PN

0W Panels Solar Fan Connection iagram

Page  of 8

ote isconnect

the solar panel fro the fan connection cable.

pen the blac connection box located on the fan by reoving the nut. dentify the positive and

negative terinals

 egative

 Positive ive

onnect the ared wires of the disconnected fan connection cable to the appropriate terinals in

the connection box. Positive to positive, negative to negative.

Ensure tight connections, then replace

the cover on the connection box.

onnect the solar panel cable to the fan connection cable.



Maintenance

The solar panel reuires no maintenance ecept occasional cleaning and replacement of damaged or

worn parts. Solar panel may be cleaned by wiping with a clean damp cloth. o not use soap or

solvents. se only identical replacement components. Components that may be suitable for one device

may create a risk of injury when used with another device.

Parts Lists

Item No. Description Qty

 Polycrystalline Solar Panel with Connecting cable

entilation Fan

Solar Panel ount racket

nstallation cessories pac



ser anual



Replacement Parts

• For replacement parts and technical uestions, please call Customer Service at

1-800-588-0590.

• Not all product components are available for replacement. The illustrations provided are a

convenient reference to the location and position of parts in the assembly seuence.

• hen ordering parts, the following will be reuired model number, and description.

• The distributor reserves the rights to make design changes and or improvements to product

lines and manuals without notice.

Page  of 8

entilation Fan onnecting cable





Please contact Nature Power Products to acuire

more information

1-800-588-0590

infonaturepowerproducts.com

www.naturepowerproducts.com

ade in China

V

Limited Warranty

Nature Power warrants our products to the original purchaser that this product is free from defects in

materials and workmanship for the period of one year from date of purchase. In addition, The solar

panel is warranted to generate up to 80 of rated power for a period of five years from date of

purchase. In the case of product defect, contact Nature Power customer service to receive

troubleshooting. If defective part or unit should be returned, a return uthoriation Number must be

issued by Nature Power and the defective part or unit should be returned to the authoried location

at the purchasers epense.  dated proof of purchase is reuired to receive warranty service. nce

received at authoried location and defect proves to be the result of defective material and

workmanship, the defective part or unit will be replaced at warrantors option and returned to the

original purchaser at warrantors epense. No refunds will be granted by the warrantor, in the event

of buyers remorse please contact your point of purchase within and in adherence to their return

policy. efunds are granted at the retailers discretions.

ated Proof of Purchase is reuired.

imitations on the arranty

This limited warranty does not cover a normal wear and tear b damage through abuse, neglect, misuse, or as

a result of any accident or in any other manner c damage from misapplication, overloading, or improper

installation d improper maintenance and repair e product alteration in any manner, and f broken glass.

Page 8 of 8

Nature Power 24208 Operating instructions

Brand: Nature Power

Model: 24208

Type: Operating instructions

Download PDF

report

Nature Power 24208 Operating instructions

Nature Power 24208 Operating instructions

Related papers

Other documents