Label Picture Description QTY
A Side Panel 2
B Back Support Bar 1
C
Seat
(Labeled with face and
bottom)
1
Label Picture Description QTY
D Bolt:M6*20MM 10
Caution: You must read this before you proceed
Single Chair
E Allen Key 1
F Seat Cushion 1
G Back Cushion 1
Before Beginning Assembly:
Step 1
Take out the silders in the four ends of the Seatboard(C ) using Allen Key(E ).
Step 3
Step 2
Insert the Seat(C) onto the Side Panel(A), as shown in the picture.
Attach Seat(C) and Side Panel(A) using Bolt(D) with Allen Key(E) as shown in the picture.
Loosely tighten the Bolts.
Step 4
Attach Back Support Bar(B) to Side Panel(A) using Bolt(D ) with Allen Key(E).
Loosely tighten the Bolts.
Stand the Chair up.
Put Back Cushion(G) and Seat Cushion(F) on the Chair, and stick the vercro.
Your Single Chair is ready for use.
Step 5
Repeat Step1 to Step 3 to attach the second Side Panel(A).
Place chair upright and test for stability.
Then in a sequential manner, proceed to fully tighten all Bolts at all joints.
Step 6
Label Picture Description QTY
A Left Leg 1
B Right Leg 1
C
Table Top Frame (with
Suction Cups)
1
D Glass Top 1
Label Picture Description QTY
E Bolt:M6*20MM 9
F Allen Key 1
Caution: You must read this before you proceed
Table
Before Beginning Assembly:
Step 1
Take out the silders in the four ends of Table Top Frame(C ) using Allen Key(F).
Step 3
Attach the Table Top Frame(C) to the Right Leg(A) using Bolt(E) and Allen Key(F) as
shown in the picture.
Loosely tighten the Bolts.
Caution: The Table and its Parts are Heavy. Two adults are required for lifting and
moving them.
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
Attach the Table Top Frame(C) to the Left Leg(A) using Bolt(E) and Allen Key(F) as
shown in the picture.
Loosely tighten the Bolts.
Caution: The Table and its Parts are Heavy. Two adults are required for lifting and
moving them.
Step 5
Place the Glass Top(D) on the assembled Table Frame.
Caution: The Table and its Parts are Heavy. Two adults are required for lifting and
moving them.
Your Table is ready for use.
Step 6
Step 4
Stand up the table, check stability and then tighten the bolts.
Note DO NOT fully tighten a BOLT in one go and then move on to the next. Rather,
In a sequential manner, gradually tighten each Bolt until all bolts are evenly
secured. This methodology will ensure maximum evenness once all Bolts are fully
tightened.
Label Picture Description QTY
A
Side Panel
1
B
Back Support Bar
1
Caution : You must read this before you proceed
Left Sofa
Page -4105 OF 10
C
Seat Panel
(Labeled with 'face' and
'bottom')
1
D
Leg Support Bar
1
E
Seat Cushion
2
F
Back Cushion
2
Label Picture Description QTY
①
Bolt (M6*20MM)
11
②
Allen Key
1
Before
Beginning
Assembly:
Page -4104 OF 10
Overview
This Sofa has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Sofa parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.
Before
Beginning
Assembly:
FRONT FACING
Leg Support Bar（D）
Side Panel（A）
Back Support Bar（B)
Seat Panel（C）
Seat Cushion（E）
Back Cushion（F）
Page -4103 OF 10
Step 1
Step 2
Place the Side Panel(A) with its inside facing up.
Insert Seat Panel(C) into the Side Panel(A).
Open the carton and place all the parts onto a clean, non-marring surface.
Remove the plastic plugs in the four ends of the Seat Board(C) using Allen Key(②) as shown
above.
Page -4102 OF 10
Step 3
Step 4
3.1) Attach the Seat Panel(C) to Side Panel(A) using Bolts(①) with Allen Key(②) as shown
above.
3.2) Attach the Seat Panel(C) to Side Panel(A) using Bolts(①) with Allen Key(②) as shown
above.
Do not fully tighten Bolts.
Page -4101 OF 10
Step 5
Attach the Back Support Bar(B) to the Side Panel(A) using Bolt(①) with Allen Key(②).
Do not fully tighten Bolt.
Insert the Back Support Bar(B) into the Side Panel(A).
Page -4100 OF 10
Step 6
Insert the Leg Support Bar(D) into the Back Support Bar(B) and Seat Panel(C) as shown above.
Page -4099 OF 10
Step 7
7.1) Attach the Leg Support Bar(D) to Back Support Bar(B) and Seat Panel(C) using Bolts(①) with
Allen Key(②) as shown above.
7.2) Attach the Leg Support Bar(D) to Seat Panel(C) using Bolt(①) with Allen Key(②) as shown
above.
Do not fully tighten Bolts.
Page -4098 OF 10
Step 8
Stand the Sofa up.
Place the Sofa on a LEVEL SURFACE.
Inspect it and make sure all parts are adequately connected.
Gently and carefully, sit onto to the Sofa.
This will help to align all parts at all the joints.
Then get off the Sofa, and in a sequential manner, proceed to tighten all Bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there are still wobbles, loosen the Bolts and execute the same process.
If the Sofa is not stable it could lead to damage to the product.
Note: This step is done best with the assistance of a second adult.
Page -4097 OF 10
Step 9
Put Seat Cushions(E) and Back Cushions(F) on the Sofa, and stick the vercro.
Your Left Sofa is ready for use.
Page -4096 OF 10
/
