King Canada KDCF-8500HEPA User manual

Brand: King Canada

Model: KDCF-8500HEPA

Type: User manual

INSTRUCTION MANUAL

MODEL: KDCF-8500HEPA

HEPA CANISTER FILTER

FOR 5 HP CYCLONE DUST COLLECTOR

DESIGNED TO FIT

5 HP CYCLONE

DUST COLLECTOR

MODEL KC-8500C

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

CANISTER FILTER

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

INTENDED FOR COMMERCIAL USE

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this product are available at our authorized King Canada service centres across Canada. Please use the 10 digit

part numbers listed in this manual for all part orders where applicable.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence

or accidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be

liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purchase to an

authorized King Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our

authorized service centres. In cooperation with our authorized serviced centre, King Canada will either repair or replace the product if

any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the

warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

ASSEMBLY

DISASSEMBLING & INSTALLING NEW CANISTER FILTER

Unbolting used canister filter

1. From inside the isolation panel, remove the 10 flange head hex. bolts (B) Fig.1

to detach canister filter (A) from the Cyclone Dust Collector housing.

Installing canister filter to Cyclone Dust Collector housing

1. Remove the canister filter shaft (A & C) Fig.2 assembly from the old canister

filter and reinstall it on the new canister filter. Tighten cap screws (B). Make

sure one cap screw is tightened against the flat of the canister filter shaft.

Tighten cap screw (D). Make sure cap screw is tightened against the flat of the

auto-clean shaft.

2. The KC-8500C Cyclone Dust Collector comes with an auto-clean motor

(shown uninstalled in Fig.3) which automatically turns the canister filter

paddles to dislodge dust. Before attempting to install the canister filter, it is

extremely important that the auto-clean shaft (C) Fig.2 gets positioned in

between the fork assembly (A) Fig.3. With the help of another person, position

the canister filter (A) Fig.1 under the main impeller housing and the isolation

panel, line up the auto-clean shaft and the fork assembly and raise the

canister filter up against the main impellor housing. Secure canister filter using

10 flange head hex. bolts (B) Fig.1.

3. Secure the canister filter dust bag to the bottom of the canister filter using the

retaining strap supplied with the Cyclone Dust Collector.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts

diagram and parts list.

FIGURE1

FIGURE2

FIGURE3

King Canada KDCF-8500HEPA User manual

King Canada KDCF-8500HEPA User manual

King Canada KDCF-8500HEPA User manual

Related papers

Other documents