King Canada KDCF-8200 User manual

Brand: King Canada

Model: KDCF-8200

Type: User manual

This manual is also suitable for

KDCF-8300

King Canada KDCF-8200 is a micron canister filter designed to fit 1.5 HP & 2 HP Cyclone Dust Collectors and 3 HP Cyclone Dust Collector, helping to keep your workspace clean and free of dust particles. With its easy-to-use top handle, you can dislodge dust buildup and maintain long-term efficiency. Periodically cleaning the filter with compressed air is also recommended.

INSTRUCTION MANUAL

MODEL: KDCF-8200

1 MICRON CANISTER FILTERS

MODEL: KDCF-8200

DESIGNED TO FIT

1.5 HP & 2 HP CYCLONE

DUST COLLECTORS

MODELS KC-8150C AND KC-8200C

MODEL: KDCF-8300

DESIGNED TO FIT

3 HP CYCLONE

DUST COLLECTOR

MODEL KC-8300C

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

CANISTER FILTER

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY

INTENDED FOR COMMERCIAL USE

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this product are available at our authorized King Canada service centres across Canada. Please use the 10 digit

part numbers listed in this manual for all part orders where applicable.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence

or accidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be

liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.

To take advantage of this limited warranty, return the product at your expense together with your dated proof of purchase to an

authorized King Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our

authorized service centres. In cooperation with our authorized serviced centre, King Canada will either repair or replace the product if

any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the

warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

ASSEMBLY, USAGE & MAINTENANCE

DISASSEMBLING & INSTALLING NEW CANISTER FILTER

Remove top handle & top plate

1. The top handle (A) Fig.1 must be removed, loosen hex. bolt (B) and slide the

top handle off the shaft.

2. The top plate (C) Fig.1 must be removed, remove the 6 hex. bolts (D) that

secure it to the Cyclone Dust Collector. Slide top plate off the shaft.

Unbolting used canister filter

1. From inside the upper housing, remove the 6 hex. bolts (A) Fig.2 to detach

canister filter from the Cyclone Dust Collector housing.

Removing handle shaft

1. The handle shaft (A) Fig.3 must be removed from the canister filter. Loosen

cap screws (B) and remove handle shaft.

Installing canister filter to Cyclone Dust Collector housing

1. Install handle shaft (A) Fig. 3 on new canister filter shaft, tighten cap screws

(B). Make sure one cap screw is tightened against the flat of the canister filter

shaft.

2. Position the new canister filter under the housing and secure it using the 6 hex.

bolts (A) Fig.2 removed previously. Obtaining help from a second person is

recommended.

3. Reinstall the top plate (C) Fig.1 using the 6 hex. bolts (D).

4. Reinstall the top handle (A) Fig.1, and tighten hex. bolt (B) on the flat portion

of the shaft.

5. Secure the canister filter dust bag to the bottom of the canister filter using the

retaining strap supplied with the Cyclone Dust Collector.

USAGE/MAINTENANCE

After considerable use, there will be dust build-up in the filter which will reduce

long term efficiency. The top handle (A) Fig.1 is used to dislodge dust build-up in

the filter. Turning the top handle rotates rubber flaps which disloge dust and

increase long term efficiency. Periodically clean the filter with compressed air.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

FIGURE1

FIGURE2

FIGURE3

King Canada KDCF-8200 User manual

Brand: King Canada

Model: KDCF-8200

Type: User manual

This manual is also suitable for

KDCF-8300

Download PDF

report

King Canada KDCF-8200 User manual

This manual is also suitable for

King Canada KDCF-8200 User manual

Related papers

Other documents