FMI GWMT1 User manual

FMI
Brand
FMI
Model
GWMT1
Type
User manual

FMI GWMT1 is a wall-mounted thermostat kit designed for use with DESA International remote-ready log sets, fireplace systems, or stoves. It allows users to remotely control the temperature of their fireplace or stove from a convenient location. The thermostat features an adjustable temperature setting and an auto mode for maintaining a consistent temperature. Installation is straightforward and requires connecting the thermostat to the fireplace or stove's control valve using the included 25 ft. wire.

FMI GWMT1 is a wall-mounted thermostat kit designed for use with DESA International remote-ready log sets, fireplace systems, or stoves. It allows users to remotely control the temperature of their fireplace or stove from a convenient location. The thermostat features an adjustable temperature setting and an auto mode for maintaining a consistent temperature. Installation is straightforward and requires connecting the thermostat to the fireplace or stove's control valve using the included 25 ft. wire.

AUTO
OFF
ON
GWMT1 Wall Mounted Thermostat Kit
For Use With DESA International Remote-Ready Log Sets, Fireplace Systems, or Stoves
READ AND FOLLOW INSTALLATION INSTRUCTIONS !
INSTALLATION SHOULD BE DONE BY A QUALIFIED INSTALLER
FAMILIAR WITH LOW-VOLTAGE WIRING PROCEDURES.
WARNING: Do not connect this thermostat or log set to any electrical source!
Electrical shock and/or fire hazard will occur.
Contents Of Kit
• Thermostat Assembly
• 25 Ft. Wire
• Mounting Screws (2)
Installation and connection:
1. Connect one terminal of 25 ft. wire to bottom contact of selector switch located on heater front control
panel (see Figure 1).
2. Connect remaining wire terminal to the “TH” terminal on the control valve (see Figure 1).
3. Route the 25 ft. wire to a convenient location.
IMPORTANT:
The wire may be shortened but must not
be lengthened.
The thermostat should be mounted 54” above the floor in a location where there is good air circulation.
Avoid heat sources such as lamps, direct sunlight, fireplace, or heat and air conditioning ducts.
4. Gently remove the cover of the thermostat from the base. Grasp the sides of the cover and separate
from the base.
5. Feed the electrical wires through the base through the holes on each side of the lower mounting
screw.
WARNING: Do not connect the thermostat to a power
source. Electrical shock and/or fire hazard will occur.
6. Connect one bare wire end to each terminal (“W” and “R”) of the thermostat base.
7. Install the base onto the wall with the provided screws.
8. Move the temperature adjustment back and forth to insure the bi-metal is free from restrictions.
9. Replace the cover onto the base. (Upon installation, the thermostat must be allowed to stabilize at
room temperature for a minimum of 30 minutes for proper operation).
Operation
1. Set selector switch to AUTO.
2. Set the temperature adjustment to the desired setting. This thermostat has been electronically cali-
brated at the factory. No adjustment or leveling is necessary.
Selector Switch
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
107235-01
Rev. A
02/00
INTERNATIONAL
Figure 1 - Connecting Wire Terminals
One terminal
of 25 ft. wire
To Wall
Thermostat
To Wall
Thermostat
107235 01
NOT A UPC
  • Page 1 1

FMI GWMT1 User manual

FMI
Brand
FMI
Model
GWMT1
Type
User manual

FMI GWMT1 is a wall-mounted thermostat kit designed for use with DESA International remote-ready log sets, fireplace systems, or stoves. It allows users to remotely control the temperature of their fireplace or stove from a convenient location. The thermostat features an adjustable temperature setting and an auto mode for maintaining a consistent temperature. Installation is straightforward and requires connecting the thermostat to the fireplace or stove's control valve using the included 25 ft. wire.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents