X-Micro mini DisGo User manual

Page is loading ...

1

INFORMATION TO USER

Product Name: X-Micro mini DisGo

Model Name: XST-HU5X / XST-HU2X / XST-HU3X / XST-HU4X

This product is in compliance with the essential

requirements and other relevant provisions of the

FCC (Federal Communications Commission)

Authorized nuder Declaration of Conformity

according to 47 CFR, Part2 , Part15 and CISPR

PUB.22 of the FCC Rules.

This equipment has been tested and found to comply with the limits for a

class B HDD device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of

the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

2

---Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

European COUNCIL DIRECTIVE 89/336/EEC

Low-voltage Directive (73/23/EEC)

This device complies with the specifications listed below:

European Standard EN 55022:1998/A1: 2000 Class B,

EN 61000-3-2:2000

EN 61000-3-3:1995 and EN 55024:1998/A1: 2001 (IEC 61000-4-2:1995,

IEC 61000-4-3:1995, IEC 61000-4-4:1995, IEC 61000-4-5:1995,

IEC 61000-4-6:1996, IEC 61000-4-8:1993, IEC 61000-4-11:1994).

3

Copyright

of this publication may be reproduced, transmitted, transcribed, stored in

a retrieval system, or translated into any language or computer language,

in any form or by any means, electronic, mechanical, magnetic, optical,

chemical, manual or otherwise, without the prior written permission of

X-Micro Technology Corp.

Disclaimer

X-Micro Technology Corp. makes no representations or warranties, either

expressed or implied, with respect to the contents hereof and specifically

disclaims any warranties, merchantability or fitness for any particular

purpose. Any software described in this manual is sold or licensed "as is".

Should the programs prove defective following their purchase, the buyer

(and not this company, its distributor, or its dealer) assumes the entire

cost of all necessary servicing, repair, and any incidental or consequential

damages resulting from any defect in the software. Further, X-Micro

Technology Corp., reserves the right to revise this publication and to

make changes from time to time in the contents hereof without obligation

to notify any person of such revision or change.

All brand and product names mentioned in this manual are trademarks

and/or registered trademarks of their respective holders.

Page is loading ...

5

Specification

Product name X-Micro mini DisGo

Capacity 5/20/30/40GB

HDD Toshiba 1.8inch

Bus interface USB 2.0

Transfer rate 480 Mbps

Spin 4200rpm

Power USB self-powered

LED Green for power, Orange for data transfer

Dimension 7 x 60 x 100 mm

Weight 85 g

Electrical +5V, 500mA Max.

OS support Windows ME/2000/ XP

Operating

requirements

Temperature from 0˚C to 50˚C

Relative humidity 5 - 90%

(Non-condensing)

6

Hardware Installation

In order to get the USB 2.0 performance, make sure to properly install the

USB 2.0 driver to your desktop computer or USB 2.0 driver to your

notebook.

Step 1. Connect the USB 2.0 cable connector

to your desktop computer or notebook.

Step 2. Connect the USB 2.0 cable mini

connector to EX HDD housing.

The LED will light after the above steps are

properly installed. Now you can check your file

manager for new external hard disk.

Important Notice

Warranty will overdue if the housing has been opened.

Shock and vibration will damage HDD, try to avoid it!

Page is loading ...

www.x-micro.com

X-Micro mini DisGo User manual

X-Micro mini DisGo User manual

in other languages

Related papers

Other documents