800-07760 10/10 Rev. A
Connecting LYNX Series Controls to the GSMX, GSMV or
7845GSMR Communications Device
For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/
Refer to the GSMX and LYNX PLUS, LYNXR-2 or LYNXR-I Installation Instructions for additional information
and procedures. If you are installing the Communications Device with a LYNX PLUS control, ensure that the
LYNXGSMEXTCB Cable Assembly is properly routed. If used, interconnecting wiring between the cable and
the communications device must not exceed 20ft in length.
Connecting the GSMX
1. Splice the stripped end of two LYNXGSMEXTCB Cable Assemblies (P/N 600-00151) to each other as shown in
Figure 1 and Table 1.
It is essential that the wires are spliced exactly as shown on Figure 1. If used, interconnecting wiring between
the two LYNXGSMEXTCB Cable Assemblies must not exceed 20ft in length.
2. Connect one end of the spliced LYNXGSMEXTCB Cable Assembly (P/N 600-00151) to the receptacle on GSMX as
shown in Figure 1.
3. Connect the other end of the spliced LYNXGSMEXTCB Cable Assembly (P/N 600-00151) to the communications
port on the LYNX PLUS, LYNXR-I or LYNXR-2 as shown in Figure 1. For the LYNX PLUS, ensure that the cable
is properly routed as shown on Figure 2.
Table 1 - Cable Assembly LYNXGSMEXTCB Splice Configuration
LYNX Series GSMX
Yellow Green
Red Black
Black Red
Green Yellow
BLACK
GREEN
RED
YELLOW
BLACK
GREEN
RED
YELLOW
SPLICE
1110
LYNX PLUS
Power Line
Carrier
Connector
Battery
Connectors
GSM/GSML
Port
Standard
RED
GREEN
YELLOW
BLACK
RED
GREEN
YELLOW
BLACK
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
Super Hi
LYNXGSMEXTCB-001-V0
GSMX
SALCLASSIC
Test
Button
LYNXR-I /
LYNXR-2
SERIES
GSM/GSML
Port
2 3 41
OR
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
Figure 1. GSMX Connections
TIE-WRAP
POINT
WIRE
ROUTING
TUNNELS
TIE WRAP
NOTE
ENSURE ALL WIRING
IS ROUTED THROUGH
WIRE STRAIN
RELIEF CLIP
WIRE STRAIN
RELIEF CLIP
TIE WRAP
MOUNT
OR
LYNXGSMEXTCB-005-V0
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
Figure 2. LYNX PLUS Cable Routing
Connecting the GSMV and 7845GSMR
Power for the GSMV or 7845GSMR is provided by the LYNX Series Control. Do not install the battery in the
GSMV or 7845GSMR. Connecting the battery will significantly decrease the backup battery life of the LYNX
Series controls.
1. Connect the connector of the LYNXGSMEXTCB Cable Assembly (P/N 600-00151) to the communications port on
the LYNX PLUS, LYNXR-I or LYNXR-2 as in Figure 3. For the LYNX PLUS ensure that the cable is properly
routed as shown on Figure 2.
2. Connect the four stripped wires from the LYNXGSMEXTCB Cable Assembly (P/N 600-00151) to the GSMV or
7845GSMR as shown in Figure 3.
3. Connect a jumper wire between Terminal 2 and 3 on the GSMV or 7845GSMR as shown in Figure 3.
LYNXR-I /
LYNXR-2
SERIES
7845GSMR
OR
GSMV
GSM/GSML
Port
LYNXGSMEXTCB-006-V0
TB 1
8765 111094321
BLACK
GREEN
RED
YELLOW
BLACK
GREEN
RED
YELLOW
Jumper
Wire
Yellow
Red
Green
2 3 41
1110
LYNX PLUS
Power Line
Carrier
Connector
Battery
Connectors
GSM/GSML
Port
Standard
Super Hi
SALCLASSIC
BLACK
GREEN
RED
YELLOW
ECP +
ECP In
GND
ECP Out
OR
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
CABLE ASSEMBLY
LYNXGSMEXTCB
(P/N 600-00151)
Figure 3. 7845GSMR or GSMV Connections
Ê800-07760@Š
800-07760 10/10 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2010 Honeywell International Inc.
www.honeywell.com/security
-
1
-
2
Honeywell 7845GSMR User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
ADEMCO LYNX-AVM Installation And Setup Manual
-
-
-
-
ADT Enterpreneur 3000EN Installation And Setup Manual
-
-
-
Lynx Dollhouse 1000-300-011-V0 User manual
-
-