Medeli M211K Owner's manual

Brand: Medeli

Model: M211K

Type: Owner's manual

ELECTRONIC

KEYBOARD

DEMO

VOLUME

START/

STOP

SYNC

START

INTRO/

ENDING FILL A FILL B MIXER FUNCTIONPIANO METROLOWER SUS TAINDUAL

M2M1 M3 M4

O.T.S.

1 2 3

4 5 6

7 8 9

TEMPO

LESSON L / R FADE

CHORD DICT.

TRANSPOSE

CHORD

PLAY

ARP.

BANK

RECORD

INFORMATION FOR YOUR SAFETY!

THE FCC REGULATION WARNING (for USA)

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

for help.

Unauthorized changes or modification to this system can

void the user's authority to operate this equipment.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe place for future reference.

Power Supply

Please connect the designated DC adaptor to an AC outlet

of the correct voltage.

Do not connect it to an AC outlet of voltage other than that

for which your instrument is intended.

Unplug the DC power adaptor when not using the instru-

ment, or during electrical storms.

Connections

Before connecting the instrument to other devices, turn off

the power to all units. This will help prevent malfunction and

/ or damage to other devices.

Location

Do not expose the instrument to the following conditions to

avoid deformation, discoloration, or more serious damage:

Direct sunlight

Extreme temperature or humidity

Excessive dusty or dirty location

Strong vibrations or shocks

Close to magnetic fields

Interference with other electrical devices

Radios and televisions placed nearby may experience

reception interference. Operate this unit at a suitable

distance from radios and televisions.

Cleaning

Clean only with a soft, dry cloth.

Do not use paint thinners, solvents, cleaning fluids, or

chemical-impregnated wiping cloths.

Handling

Do not apply excessive force to the switches or controls.

Do not let paper, metallic, or other objects into the instru-

ment. If this happens, remove the electric plug from the

outlet. Then have the instrument inspected by qualified

service personnel.

Disconnect all cables before moving the instrument.

CAUTION

The normal function of the product may be disturbed

by Strong Electro Magnetic Interference. If so, simply

reset the product to resume normal operation by

following the owner's manual. In case the function

could not resume, please use the product in other

location.

Contents

Panel & Display Description

Front Panel..................................................................4

Rear Panel...................................................................5

Display.........................................................................5

Setup

Power Supply...............................................................6

Connections

Connecting an MP3/CD Player....................................7

Connecting an Audio Equipment.................................7

Connecting a pair of Headphones...............................7

Connecting a Microphone............................................7

Connecting a Sustain Pedal........................................7

Connecting a Computer...............................................7

Power Switch and Master Volume...........................8

Playing the Demos....................................................8

Playing the Voices

Playing a Voice............................................................9

Playing Two Voice Simultaneously-DUAL...................9

Playing Different Voices with Both hands-LOWER.......9

Touch...........................................................................9

Sustain.......................................................................10

DSP Effect.................................................................10

Transpose..................................................................10

Octave.......................................................................10

Piano Mode...............................................................10

Auto Accompaniment

Selecting a Style........................................................11

Playing a Fill..............................................................11

Intro/Ending...............................................................11

Sync Start..................................................................12

Fade In/Out................................................................12

Accompaniment Volume............................................12

Tempo........................................................................12

Auto Bass Chord.......................................................13

Chord Basics.............................................................13

One Touch Setting.....................................................14

Metronome

Turning on the Metronome........................................14

Selecting the Beat.....................................................14

Arpeggiator..............................................................15

Mixer.........................................................................15

Function Menu

Tune...........................................................................16

Octave.......................................................................16

Split Point...................................................................16

Beat Type...................................................................17

Touch.........................................................................17

Modulation.................................................................17

DSP............................................................................17

Reverb Type..............................................................17

Reverb Level.............................................................17

Chorus Type..............................................................18

Chorus Level.............................................................18

Auto Power Off..........................................................18

Selecting a Registration Bank....................................19

Chord Dictionary.....................................................19

Playing the Songs

Listening to the Songs...............................................20

Lesson Mode.............................................................20

Recording and Playback.........................................21

MIDI Function

What’s MIDI?.............................................................21

MIDI Connection........................................................21

Trouble Shooting.....................................................22

Specifications..........................................................22

Appendices

Voice List...................................................................23

Style List....................................................................28

Song List....................................................................30

MIDI Implementation Chart........................................32

DEMO

VOLUME

START/

STOP

SYNC

START

INTRO/

ENDING FILL A FILL B MIXER FUNCTIONPIANO METROLOWER SUS TAINDUAL

M2M1 M3 M4

O.T.S.

1 2 3

4 5 6

7 8 9

TEMPO

LESSON L / R FADE

CHORD DICT.

TRANSPOSE

CHORD

PLAY

ARP.

BANK

RECORD

DEMO

VO LUME

START/

STOP

SYNC

START

INTRO /

ENDIN G FILL A FILL B MIXE R FUNCTIONPIANO METROLOWER SUSTAI NDUAL

M2M1 M3 M4

O. T.S.

1 2 3

4 5 6

7 8 9

TEMPO

LESSO N L / R FADE

CHORD DI CT.

TRANSPOSE

CHOR D

PLAY

AR P.

BANK

RECORD

Panel & Display Description

Front Panel

1. [VOLUME] Knob

Adjust the master volume.

2. [ ] Button

Turn the power on or off.

3. [LESSON] Button

Enter the lesson mode.

4. [L/R] Button

Choose to practice the left hand

or right hand part.

[CHORD DICT.] Button

Turn the chord dictionary function

on or off.

5. [FADE] Button

Turn the Fade In/Out function on

or off.

6. [TEMPO +/-] Buttons

Adjust the current tempo value.

7. [CHORD] Button

Enter the Chord Mode.

8. [INTRO/ENDING] Button

Play the Intro or Ending pattern.

9. [FILL A] Button

Play the fill-in pattern A.

10. [FILL B] Button

Play the fill-in pattern B.

11. [SYNC START] Button

Turn the Sync Start function on

or off.

12. [START/STOP] Button

Start or stop playing the style or

song.

13. [BANK] Button

Switch between memory banks.

[STORE] Button

14. [M1]~[M4] Buttons

Recall the registered panel settings.

15. [O.T.S.] Button

Turn the One Touch Setting

function on or off.

16. [RECORD] Button

Enter the Record Mode.

[PLAY] Button

Play back the recording.

17. [DUAL] Button

Turn the dual function on or off.

18. [LOWER] Button

Turn the lower function on or off.

19. [SUSTAIN] Button

Turn the sustain function on or off.

20. [VOICE] Button

Switch to Voice Mode.

Press [VOICE] and [STYLE] at the

same time to enter Demo Mode.

21. [STYLE] Button

Switch to Style Mode.

Press [VOICE] and [STYLE] at the

same time to enter Demo Mode.

22. [SONG] Button

Switch to Song Mode.

[ARP.] Button

Turn the Arpeggiator function on

or off.

23. [PIANO] Button

Turn the Piano Mode on or off.

24. [METRO] Button

Turn the metronome on or off.

25. [TRANSPOSE] Button

Adjust the Transpose value.

26. [MIXER] Button

Enter the Mixer menu.

27. [FUNCTION] Button

Enter the function menu.

28. [+]/[-] and Number Buttons

Set parameters value or select

the number.

29. LCD Display

Display all parameters and values

related to the current operation.

2012

13 15

16 17 18 19

6 7

8 9 10

21 22 24 272623 25

Panel & Display Description

Rear Panel

1. RECORD/PLAY/MODULATION

2. NUMBER

3. VOICE/STYLE/DEMO/SONG

4. CHARACTER

5. ARP/ TOUCH/SUSTAIN

6. RECORD

7. TREBLE CLEF

8. BASS CLEF

9. MEASURE

10. BEAT

11. TEMPO

12. CHORD

13. MEMORY/O.T.S.

14. A.B.C./FULL RANGE/FADE/A/B

15. NOTE INDICATION

16. LESSON

17. DUAL/LOWER/DSP

30. USB Jack

Connect to a computer.

31. SUSTAIN Jack

Connect a sustain pedal.

32. PHONES/OUTPUT Jack

Connect a pair of headphones or an

audio equipment.

33. AUX IN Jack

Connect an external audio source,

such as MP3 or CD player.

34. MIC Jack

Connect a microphone.

35. DC IN Jack

Connect the DC 12V power adapter.

Display

HARMONY

ARP.

SUSTAIN

31 32 33 34 35

Setup

This section contains information about setting up your instrument

and preparing to play. Please go through this section carefully

before turning the power on.

Power Supply

You can power the instrument either by batteries or by power adaptor.

Follow the instructions described below.

Using Batteries

The instrument needs 6 pieces of AA (NO.5) or equivalent alkaline

batteries for power supply.

1. Open the battery cabinet cover located on the bottom of the

instrument.

2. Insert the batteries, carefully following the polarity markings on the

cabinet.

3. Replace the cabinet cover. Make sure it locks firmly in place.

Notes:

1. Do not mix using any used and new batteries.

2. Always use the same types of batteries.

3. Remove the batteries when the instrument is not in use for a long

period of time.

Using Power Adaptor

1. Turn down the volume before connecting to power supply.

2. Connect the adaptor to the DC IN jack of the instrument.

3. Plug the adaptor into an AC outlet. This will automatically cut off

the battery power supply.

Notes:

1. In order to save energy, the instrument will automatically shut down

after 30 minutes if it is not used. (Please refer to Auto Power Off).

2. For your safety, please unplug the instrument when it is not in use

or during a thunderstorm.

Connecting an MP3/CD Player

The rear-panel AUX IN jack receives audio signals from an external

audio source such as an MP3 or a CD player.

Use an audio cable to connect the AUX IN jack of the instrument to

the OUTPUT jack of the MP3/CD player. The instrument’s speakers

will play the music transmitted from the external player, and you can

play along.

Connecting an Audio Equipment

The rear-panel PHONES/OUTPUT jack delivers the output of the

instrument to an external audio equipment such as a keyboard

amplifier, a stereo sound system, a mixing console, or a recorder.

Use an audio cable to connect the PHONES/OUTPUT jack of the

instrument to the INPUT jack of the external audio equipment.

Notes:

1. Turn off the power to all units before connecting or disconnecting

the external equipment.

2. To avoid damaging the speakers, please set the master volume

to minimum level before turning on the power.

Connecting a pair of Headphones

A standard pair of stereo headphones can be connected to the

PHONES/OUTPUT jack for private practice or late-night playing.

The internal stereo speaker system is automatically shut off when a

pair of head phones is plugged into this jack.

Note:

Do not listen with the headphones at high volume for long periods

of time. Doing so may cause hearing loss.

Connecting a Microphone

You can plug a microphone to the MIC jack to sing along with your

keyboard performance or song playback.

1. Set the master volume to minimum level before connecting or

disconnecting a microphone.

2. Plug a microphone into the MIC jack.

3. Adjust the master volume to an appropriate level.

Connecting a Sustain Pedal

An optional footswitch can be plugged into the sustain jack and be

used to switch sustain on or off. Simply by pressing the pedal, you

will have a natural sustain as you play.

Connecting a Computer

Use a standard USB cable to connect the USB jack of the instru-

ment to the USB port of a computer. You can transmit MIDI

messages between the instrument and the computer.

Notes:

1. Do not set the USB device to be input and output simultaneously

when setting the software on the computer. Otherwise, the sound

will be overlapped when playing the keyboard.

2. We recommend using a USB2.0 interface to connect the

instrument to computer.

Connections

Power Switch

Before you switch your instrument on, please turn down the volume

of instrument and the connected audio equipment first.

1. Make sure the instrument is properly connected to power supply.

2. Press POWER SWITCH, the LCD screen is lit, and displays

“Loading!”, indicating the instrument is powered on.

Master Volume

Rotate the [VOLUME] knob clockwise to increase the master

volume or counter-clockwise to decrease it. You can use the knob

to set the desired volume level.

Note:

If the speakers do not produce sound, please check if the master

volume is set too low or if headphones are plugged into the

PHONES jack.

Power Switch and Master Volume

The instrument features a variety of demo songs.

1. Press the [STYLE] and [VOICE] buttons simultaneously to start

playing all demo songs in a loop. The LCD will display the current

demo number and name.

2. Select a demo song.

Use the number keys, the [+]/[-] buttons to select the desired

demo song.

3. Press the [STYLE] and [VOICE] buttons simultaneously again or

press the [START/STOP] button to stop playing and exit the demo

mode.

Note:

During demo playback, only the following buttons will work:

[START/STOP], [TEMPO -]/[TEMPO +], [+]/[-], the Number buttons,

[VOLUME] and [POWER].

Playing the Demos

DEMO

1 2 3

4 5 6

7 8 9

DUAL

The instrument features a variety of exceptionally realistic voices. Please

refer to Voice List.

Playing a Voice

1. Press the [VOICE] button.

Enter the VOICE mode. LCD shows “VOICE R1”, the voice number and

the voice name.

2. Select a voice.

Use the number keys, the [+]/[-] buttons to select the voice you want to

play.

3. Play the voice.

Play the keyboard and enjoy the beautiful voice.

Note:

When the DUAL and LOWER function is on, you can press [VOICE] button

repeatedly to choose the voice source. The corresponding LCD indicator

will highlight between R1, R2, and L.

Playing Two Voice Simultaneously-DUAL

1. Press the [DUAL] button to turn on the dual function. LCD shows

“VOICE R2”, the dual voice number and name.

2. Use the number keys, the [+]/[-] buttons to select a voice for VOICE R2.

3. Play the keyboard, you will hear two different voices layered together,

just like two different instruments being played at the same time.

4. Press the [DUAL] button again to turn off the dual function.

Playing Different Voices with Both hands-

LOWER

The Lower function splits the keyboard into two areas so as to create

different voices for each of your hands. The left hand voice is the lower

voice “L” .

1. In idle mode, press the [LOWER] button to turn the lower function on.

The LCD displays the left hand voice name and number, and the

indicator “VOICE L” and “LOWER”.

2. Use the number keys, the [+]/[-] buttons to select a voice for VOICE L.

3. Play the keyboard with both hands, and you will hear two different

voices.

4. Press the [LOWER] button again to turn off the lower function.

Split Point

The key on the keyboard that separates voice L and voice R1/R2 is called

the “split point”. The default split point is at F#3 (19) , however you can

assign it to any other key. Refer to the Function Menu.

Touch

The keyboard is equipped with a touch response feature that lets you

dynamically and expressively controls the level of the voice with your

playing strength – just as on an acoustic instrument. Please refer to the

function menu to adjust the touch level.

Playing the Voices

1 2 3

4 5 6

7 8 9

LOWER

Sustain

When the Sustain feature is ON, all notes played on the keyboard will

have a longer sustain. Press the [SUSTAIN] button to turn sustain on or

off.

Note:

When using a sustain pedal, you can produce a much stronger and more

natural sustain effect than by using the [SUSTAIN] button.

DSP Effect

The DSP simulates sounds in real environment. With the DSP effects,

you can add ambiance and depth to your performance in a variety of

ways.

The function is turned on by default. You can refer to the function menu

to turn the DSP effect on or off.

Transpose

Transpose function allows the overall pitch of the instrument to be

transposed up or down by one octave in semitone steps.

1. the [TRANSPOSE] button to enter transpose menu. The LCD shows

the current transpose value.

2. Use [+]/ [-] buttons to adjust the transpose value.

3. Press the [+] and [-] buttons simultaneously to reset the transposition

to 0.

Octave

The octave function will shift the pitch of the specified voice layer up or

down in the step of an octave.

You can refer to the function menu to adjust the octave value.

Note:

After adjusting the octave, notes in the highest and lowest keyboard

range may not sound normally.

Piano mode

This function is to set the voice of the entire keyboard to piano instantly.

1. Press [PIANO] button to enter or exit piano mode.

2. In piano mode, you can play the accompaniment as in the other

modes, but it plays only the rhythm part.

Note:

In piano mode, the A.B.C. is automatically turned off.

Playing Voices

TRANSPOSE

SUSTAIN

PIANO

SYNC

START

The auto accompaniment function puts a full backing band at your

fingertips. All you have to do is to play chords with your left hand, and

the accompaniment will automatically play along, instantly following the

chords you play. With auto accompaniment, even a solo performer can

enjoy playing with the backing of an entire band or orchestra.

The instrument features a variety of styles, please refer to the Style

List. Try selecting the different styles and enjoy the auto accompani-

ment.

Selecting a Style

1. Press the [STYLE] button.

Enter the STYLE mode. LCD shows “STYLE”, the style number and

the style name.

2. Use the number keys, the [+]/[-] buttons to select the style you want

to play.

3. Press the [START/STOP] button to start the rhythm tracks of the

auto accompaniment.

Sync Start

When style stops, press the [SYNC START] button to turn on the

function. The beats on LCD will flash along with the tempo.

1. In Sycn Start mode, if the A.B.C. function is turned off, you can press

a key on the keyboard to start playing auto accompaniment of the

rhythm track.

2. In Sycn Start mode, if the A.B.C. function is in use, you can press a

key on the chord range of the keyboard to start playing auto

accompaniment of all tracks.

Intro/Ending

The intro is an opening section of a song. When the intro pattern

finished, the system will automatically shift to the main section.

Ending is the ending section of a song. When the ending is finished,

accompaniment automatically stops.The length of the ending differs

depending on the selected style.

1. Press the [STYLE] button.

2. Select a style.

3. Turn the Chord Mode on.

4. Turn SYNC START on.

5. Press the [INTRO/ENDING], the “A” or “B” flashes on LCD, the style

is ready to play.

6. It will start the accompaniment as soon as you start playing in Chord

section. When the playback of the intro is finished, it automatically

switched to main A or B section.

7. Press the [INTRO/ENDING] again to play the ending section.

When the ending is finished, the auto accompaniment automatically

stops.

Note:

If you press [FILL A] or [FILL B] before the ending is finished, it will play

a fill-in then switch to the corresponding main section.

Auto Accompaniment

1 2 3

4 5 6

7 8 9

CHORD

START/

STOP

SYNC

START

INTRO/

ENDING

FILL A FILL B

TEMPO

Playing a Fill

Auto fill in function automatically adds a fill to your performance. When

the fill-in is finished,accompaniment shifts to the Main section (A,B).

Note:

If you keep pressing [FILL A]/[FILL B] buttons during style playback,

the fill-in pattern will repeat playing until the button is released.

Playback will then shift to the related MAIN section.

When style stops, press the [FILL A]/[FILL B] buttons to select a MAIN

section. “A or B” will highlight on LCD.

Fade In/Out

Fade In

Starting the style with fade in produces a smooth beginning, the

volume increases from low to high. Press the [FADE] button when

Style is stoppedLCD will show FADE. Press the [START/STOP]

button to start Style playing. LCD will showFADE.

The Accompaniment Volume will change from 0 to the set value in

about 8 seconds. The keyboard volume will change from 0 to default

value at the same time.

Fade Out

Stopping the style with fade out produces a smooth ending, the

volume decreases from high to low. Press the [FADE] button during

Style playing. LCD will show FADE.

The Accompaniment Volume will change from the set value to 0 in

about 8 seconds, and the style stops.

Accompaniment Volume

The function adjusts the accompaniment volume, so as to keep an

appropriate balance between the accompaniment volume and the

voice volume.

Press repeatedly the [MIXER] button to enter the mixer menu, and

when the LCD displays "Accomp", you can adjust the volume level

over the range of 0-32. LCD will show the current volume level.

Notes:

In the mixer menu, press both [-] and [+] buttons simultaneously to

mute the accompaniment part. LCD shows “OFF Accomp”. Press both

buttons again to unmute the accompaniment volume.

Tempo

Each style of the instrument has been programmed with a default

tempo; however, you can change it as needed.

1. Use the [TEMPO -]/[TEMPO +] buttons to change the tempo. The

value ranges from 30 to 280.

2. Hold down the [TEMPO -]/[TEMPO +] buttons to change the tempo

quickly.

3. Press the [TEMPO+] and [TEMPO-] buttons simultaneously to

restore the default tempo setting.

Auto Accompaniment

FILL A FILL B

FADE

MIXER

CHORD

Auto Bass Chord

1. Press the [CHORD] button, the LCD will display the “A.B.C.”

indicator. The left hand section of the keyboard is the chord section.

You can play different chords in the chord section.

Press [CHORD] button again to enter Full Range mode. The “FULL

RANGE” indicator will be lit. You can play chords over the entire

keyboard in multi-fingering.

2. Play chords in the chord section, and the LCD will display the

corresponding chord names.

3. Split Point Setting

Please refer to the function menu to set the split point. The split

point and the keys to its left all belong to the chord section.

Auto Accompaniment

Chord Basics

A chord, in music, is any harmonic set of three or more notes that is

heard as if sounding simultaneously. The most frequently encountered

chords are triads. A triad is a set of three notes that can be stacked in

thirds. When stacked in thirds, the triad's members, from lowest

pitched tone to highest, are called: the Root, the Third, and the Fifth.

Triad Type

There are following basic triad types:

Chord Inversion

We define this chord its root is not in the bass (i.e., is not the lowest

note) as an inversion chord. When the root is in the bass, we call the

chord: root-position chord. If we put the Third and Fifth in the root

position, then it forms “Inversion”, we call this chord “Inversion Chord”.

See the following major triad and its inverted chord.

Chord Name

The chord name contains two parts content: Chord root and Chord type.

Single Finger

Single finger type not only can detect single finger but also can detect

multi finger. And the single finger makes it easily to play chords through

only one, two or three keys. Including major, minor, seventh, and minor

seventh chord. Refer to relevant picture on the right for details.

Major Triad

Minor Triad

Augmented

Triad

Diminished

Triad

A root with a major third added above and a perfect fifth

will consist as a “Major Triad”.

A root with a minor third added above and a perfect fifth

will consist as a “Minor Triad”.

A root with a major third added above and an

augmented fifth will consist as an “Augmented Triad”.

A root with a minor third added above and a diminished

fifth will consist as a “Diminished Triad”.

TEMPO

O.T.S.

Auto Accompaniment

Metronome

Multi-finger

Multi-finger allows you to play chords in normal fingering. Try playing

the 32 chord types in C scale as listed on the right.

Note:

In full range mode, the entire keyboard will only recognize chords

played in normal fingering.

One Touch Setting

When One Touch Setting is switched on, you can instantly recall all

auto accompaniment related settings including voices selection and

digital effects simply with a single touch of a button.

1. Press the [O.T.S.] button to turns on the One Touch Setting for

current style. LCD shows “O.T.S.”.

2. Press one of the [M1]-[M4] buttons, various panel settings (such as

voice, effect, etc.) that match the selected style can be instantly

recalled.

3. A.B.C. is automatically turned on during O.T.S. mode.

4. Press the [O.T.S.] button again to quit One Touch Setting mode,

the “O.T.S.” indicator will disappear.

Note:

In O.T.S. mode, the memory is not selectable.

Turning on the Metronome

Press the [METRO] button to turn on the metronome.

Press the [METRO] button again to turn off the metronome.

Press the [TEMPO+] / [TEMPO-] buttons to change the tempo of the

metronome.

Selecting the Beat

You can set the beat type in the function menu, please refer to the

function menu for details.

If you turn on the metronome during style playback, the metronome

sound will start from the next beat and its beat will match the current

style. When style stops, you can change the metronome beat as

desired.

The metronome is not usable in song mode.

METRO

The Mixer allows you to adjust separately the volume of different tracks.

1. Press the [MIXER] button to enter the mixer menu, the LCD displays

the current mixer track.

2. Repeatedly press the [MIXER] button to select the track you want.

Then use [+]/[-] buttons to change the parameters.

The option and parameters are as follows:

Note:

It will exit the mixer menu if there is no operation in 3 seconds. Pressing

[+] and [-] buttons at the same time will mute the selected track, the

LCD will display “OFF”. Press the two buttons at the same time again to

unmute the track.

Mixer

Arpeggiator

The arpeggiator function will automatically generate arpeggios. Simply

play a chord with your left hand, and the instrument will play a preset

arpeggio pattern to produce a beautiful melody.

Turn the Arpeggiator on or off

Press and hold the [ARP.] button for 2 seconds to turn on the function.

The corresponding indicator will be lit. Press and hold the [ARP.] button

for 2 seconds again to turn off the function. The corresponding indicator

will light off.

Note:

Each voice is matched with a preset arpeggio pattern, so when you

change the voice, the default arpeggio pattern will change as well.

The Split Point of Arpeggiator

When you turn on the arpeggiator, the keyboard will be split into two

areas. Play chords in the left hand area, and melody in the right hand

area. The default split point is the same as in the lower function: F#3

(19).

Options

Adjust the Accomp volume

Adjust the Rhythm track volume

Adjust the Bass track volume

Adjust the Chord 1 track volume

Adjust the Chord 2 track volume

Adjust the Chord 3 track volume

Adjust the Upper 1 track volume

Adjust the Upper 2 track volume

Adjust the Lower track volume

LCD Display

XXX Accomp

XXX Rhythm_m

XXX Bass

XXX Chord1

XXX Chord2

XXX Chord3

XXX Upper1

XXX Upper2

XXX Lower

Range

0-32

ARP.

MIXER

FUNCTION

Press the [FUNCTION] button to enter the function menu. The LCD

displays the current parameter item.

Press repeatedly the [FUNCTION] button to select an item, then use

the [+]/ [-] buttons to change the value of the selected item.

Parameter items and the value range in the function menu:

Note:

It will exit the function menu if there is no operation in 3 seconds.

Tune

The function adjusts the pitch of the entire keyboard in a 2-cent increment.

1. Repeatedly press the [FUNCTION] button to select the tune menu.

The LCD displays “Tune”.

Use the [+] / [-] buttons to change the value over the range of -50 - +50.

2. Pressing [+] and [-] buttons at the same time will reset the tune value

to default “000”.

The setting applies to both accompaniment and the voice.

Octave

1. Repeatedly press the [FUNCTION] button to select the octave menu.

The LCD displays “Octave”.

Use the [+] / [-] buttons to change the value over the range of -2 - +2.

2. Pressing [+] and [-] buttons at the same time will reset the octave value

to default “000”.

Split Point

The Point on the keyboard that separates voice L and voice R1/R2 is

called the "split point". Left hand section controls the auto bass chord

accompaniment when the A.B.C. function is on, or it plays the lower voices

when the A.B.C. function is off.

1. Repeatedly press the [FUNCTION] button to select split point menu.

The LCD displays “Split Pt”. Use [+] / [-] buttons to change Split Point.

The range of Split Point is: 1~61.

2. Press [+] / [-] buttons simultaneously will set the split point value to its

default setting: F#3 (19).

Parameter Item

Tune

Octave

Split Point

Beat Type

Touch

Modulation

DSP

Reverb Type

Reverb Level

Chorus Type

Chorus Level

Auto Power Off

LCD Display

XXX Tune

XXX Octave

XXX Split Pt

XXX Beat

XXX Touch

XXX Modul

XXX Dsp

XXX Rev Type

XXX Rev Lev

XXX Chr Type

XXX Chr Lev

XXX PowerOff

Range

-50 - +50

-2 - +2

1 - 61

0, 2 - 9

OFF, 1 - 3

On, OFF

1 - 10

0 - 32

1 - 8

0 - 32

OFF, 30, 60

Function Menu

Beat Type

1. Repeatedly press the [FUNCTION] button to select the beat menu.

The LCD displays “Beat”.

Use the [+ ]/ [-] buttons to change the beat type.

2. Pressing [+] and [-] buttons at the same time will reset the beat type

to default “004”.

Touch

1. Repeatedly press the [FUNCTION] button to select the touch menu.

The LCD displays “Touch”.

Use the [+ ]/ [-] buttons to change the touch level.

2. Pressing [+] and [-] buttons at the same time will reset the touch level

to default “002”.

Modulation

Repeatedly press the [FUNCTION] button to select the modulation menu.

The LCD displays “Modul”.

Use the [+] / [-] buttons to switch modulation on or off.

Note:

Modulation is not available for percussive voices.

DSP

Repeatedly press the [FUNCTION] button to select the DSP menu. The

LCD displays “Dsp”.

Use the [+] / [-] buttons to switch DSP on or off.

Reverb Type

1. Repeatedly press the [FUNCTION] button to select the reverb type

menu. The LCD displays “Rev Type”.

Use the [+]/ [-] button to change the type value.

2. Pressing [+] and [-] buttons at the same time will reset the reverb type

to default “004”.

Reverb Level

1. Repeatedly press the [FUNCTION] button to select the reverb level

menu. The LCD displays “Rev Lev”.

Use the [+]/ [-] button to adjust the level over the range of 0-32.

2. Pressing [+] and [-] buttons at the same time will reset the reverb level

to default.

Function Menu

Chorus Type

1. Repeatedly press the [FUNCTION] button to select the chorus type

menu. The LCD displays “Chr Type”.

Use the [+]/ [-] button to change the type value.

2. Pressing [+] and [-] buttons at the same time will reset the chorus type

to default “003”.

Chorus Level

1. Repeatedly press the [FUNCTION] button to select the chorus level

menu. The LCD displays “Chr Lev”.

Use the [+]/ [-] button to adjust the level over the range of 0-32.

2. Pressing [+] and [-] buttons at the same time will reset the chorus level

to default.

Auto Power Off

1. Repeatedly press the [FUNCTION] button to select the power off

menu. The LCD displays “PowerOff”.

Use the [+]/ [-] button to change the time setting.

2. Pressing [+] and [-] buttons at the same time will reset the setting to

default “030” (30 min).

Function Menu

L / R

CHORD DICT.

The Registration Memory feature allows you to save virtually all panel

settings to a registration memory, and you can instantly recall them by

pressing a single button.

The instrument has 8 memory banks, and each bank has 4 memories

(M1-M4).

1. Hold down [STORE] button , then press one of the memory buttons

[M1] - [M4] to save the panel settings. The LCD will display “Mem

Stor” and the new settings will replace the previous memory data.

2. Press one of the memory buttons [M1] - [M4] to recall the panel

settings saved to that memory.

3. You can save following parameters to the memory:

Voice Parameter: voice, dual, DSP, mixer.

Accompaniment Parameter: style, tempo, and chord no/off,

accompaniment sections.

Function Parameter: touch, some parameters in the function menu.

Note:

Registration memory cannot be recalled when the One Touch Setting

function is in use. The registration memory will reset to default settings

after power off.

Selecting a Registration Bank

1. Press the [BANK] button. The LCD will display the bank number.

2. Repeatedly press the [BANK] button to select a bank over the range

of 1-8.

If you know the name of a chord but don't know how to play it, you can

use the Chord Dictionary function.

1. Press and hold the [CHORD DICT.] button for 2 seconds to enter this

mode. The LCD displays the Chord Type and Chord Notes.

2. The keys above C4 (including C4) are used to assign the Chord Type,

and the keys above C6 (including C6) are used to assign the Chord

Root. When the Chord Type and Chord Root are confirmed, the LCD

will display the Chord and the staff notation.

3. When you play the correct chord on the chord range of the keyboard,

an applause sound will be heard.

4. Press and hold the [CHORD DICT.] button for 2 seconds again to exit

this mode.

Chord Dictionary

M2M1 M3 M4BANK

BANK

The instrument has a variety of songs (Please refer to the Song List).

Each song can be practiced in LESSON mode.

Listening to the Songs

1. Press the [SONG] button to enter the song mode. It will play all

songs circularly. Press the [SONG] button again, it will stop the song.

2. In song mode, use the number keys and [+]/[-] buttons to select a

song.

3. During song playback, you can press the [START/STOP] button to

stop the song, press it again to play the current song repeatedly.

4. Use the [TEMPO+]/[TEMPO-] buttons to change the tempo of the

current song.

5. When the song is stopped, press [STYLE], [VOICE], [DUAL],

[M1] - [M4] to exit the song mode.

Lesson Mode

The instrument presets 3 different ways to practice a song, as specified

in Lesson 1, Lesson 2 and Lesson3. The instrument will grade your

practice when you finish a lesson, helping you to keep track of your

progress.

1. When song playback is stopped, press the [LESSON] button to enter

the lesson mode or select a lesson to practice.

2. Press the [START/STOP] button to start the lesson. The LCD displays

the note that needs to be played.

3. Press the [START/STOP] button again to stop the lesson.

4. In lesson mode, press repeatedly the [L/R] button to select to practice

the left hand part, the right hand part, or both hands.

5. You can select to practice one of the three lessons. It will grade your

practice when you finish a lesson.

In lesson 1, you will learn to practice at the correct time value. It doesn't

matter even you play the wrong notes.

In lesson 2, you will learn to play the correct notes. The lesson will

continue only when you have played correctly the note displayed on

LCD.

In lesson 3, you will learn to play the correct notes at the correct time

value.

When you finish a lesson, the instrument will grade your practice by

telling you the level you get.

Level 1: OK.

Level 2: Good.

Level 3: Very Good.

Level 4: Excellent.

After grading, the song will play back again, and you can practice again.

Playing the Songs

L / R

CHORD DICT.

LESSON

Page is loading ...

Medeli M211K Owner's manual

Medeli M211K Owner's manual

Medeli M211K Owner's manual

Related papers

Other documents