Weston 16-0501-W User guide

Category
Slicers
Type
User guide
MANDOLINE SLICER
16-0501-W
DUE TO CONSTANT FACTORY IMPROVEMENTS, THE PRODUCT PICTURED MIGHT DIFFER
SLIGHTLY FROM THE PRODUCT IN THIS BOX. 071015
1. KEEP FINGERS CLEAR of the Blade at all times. NEVER push the
product with your hands in line of the Blade when slicing. ALWAYS use the
Food Pusher.
2. NEVER use ngers to scrape food away from the Blade. SEVERE INJURY
MAY RESULT.
3. NEVER LEAVE THE SLICER UNATTENDED. Close supervision is necessary
when used near children. The Slicer is NOT to be used by children. The Slicer is
NOT a toy.
4. CHECK FOR DAMAGED PARTS. Before using the Slicer, check that all
parts are operating properly and perform the intended functions.
5. The manufacturer declines any responsibility in the case of improper use of
this unit.
6. NEVER use any accessories or parts from other manufacturers. Doing so will
VOID YOUR WARRANTY and may cause injury.
7. Be sure the Mandoline Slicer is stable during use. Both Front and Rear
Stand should be securely on the work surface.
8. DO NOT use this Slicer for frozen foods or anything other than food stuffs.
9. Remove the Blade after each use to clean. Clean with hot soapy water.
Dry thoroughly. Protective/cut-resistant gloves are recommended whenever
handling the Blades.
10. DO NOT use the Slicer while under the inuence of drugs or alcohol.
GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS AND WARNINGS
PRIOR TO USING THIS UNIT. YOUR SAFETY IS MOST IMPORTANT!
FAILURE TO COMPLY WITH PROCEDURES AND SAFE GUARDS MAY
RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. REMEMBER:
YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY!
SAVE THESE INSTRUCTIONS
3
ENGLISH INSTRUCTIONS
ENGLISH INSTRUCTIONS
4
COMPONENT LIST
DIAGRAM NUMBER PART DESCRIPTION PART NUMBER
1 SLICER BODY N/A
2 BLADE COVER N/A
3 BLADES & BLADE BOX (3B) 16-0503
COARSE GRATER
FINE GRATER
MEDIUM GRATER
FLAT SLICER BLADE
WAVY SLICER BLADE
4 FOOD PUSHER N/A
If any components of this unit are broken, the unit does not operate properly or you
need a replacement instruction manual, visit us on the web at
WestonProducts.com
Or call Weston Brands LLC Toll Free at 1-800-814-4895
Monday thru Friday 8:00am-5:00pm ET. Outside the U.S. call 001-440-638-3131
Depth
Adjustment
Knob
Rear
Stand
Bottom
View of
Food
Pusher
1
4
Spikes
Julienne
Blade
Knob
Grater
Blade (7mm)
Fine
Shredder
Blade
(2.5mm)
Coarse
Shredder
Blade (6mm)
Flat
Slicer
Blade
Wavy
Slicer
Blade
Julienne
Blades
2
(Underneath)
3
Blade
Assortment
Shown Below
Depth
Plate
3B
5
ENGLISH INSTRUCTIONS
ASSEMBLY & USE INSTRUCTIONS
It is recommended that the
Slicer be thoroughly cleaned
prior to use! Refer to Cleaning
Instructions in this booklet.
1. Make certain the Julienne
Blades are locked down
inside the Slicer by pulling out
on the Julienne Blade Knob
and turning it. Check that
the Blade Cover is securely
closed. FIGURE A & B
2. Make certain the Depth
Plate is in the highest position
by pulling out on the Depth
Adjustment Knob and turning
it counter-clockwise until it is
fully raised. FIGURE A & B
3. Using a at and sturdy work
surface, unfold the Rear Stand
of the Slicer Body. Position
the Slicer with the Rear Stand
furthest from you.
4. To insert your Blade of
choice, carefully remove the
Blade from Blade Box, holding
it by the plastic portion, away
from the sharp blade.
5. Insert the posts of the Blade
into the notches on the Slicer
Body. FIGURE D1 & D
6. Push down on the plastic
portion of the Blade to snap
into place.
FIGURE A
FIGURE B
UNDERSIDE OF SLICER
FIGURE D1
FIGURE D
Julienne
Blade Knob
Depth
Adjustment Knob
Blade Cover
Julienne Blades
Blade
Thumbslot
FIGURE C
Rear Stand
Julienne
Blades
Depth
Plate
CAUTION SHARP!
CAUTION SHARP!
Posts
of Blade
WARNING
SHARP BLADES
KEEP FINGERS CLEAR OF BLADE
AREA! Protective/cut-resistant gloves
recommended whenever handling the
Blades!
WARNING
SHARP BLADES
KEEP FINGERS CLEAR OF BLADE
AREA! Protective/cut-resistant gloves
recommended whenever handling the
Blades!
6
ENGLISH INSTRUCTIONS
7. Stab the food to be sliced onto the
spikes of the Food Pusher. FIGURE E
ALWAYS use the Food Pusher!
NEVER use your ngers, hands or
other objects to push the food on the
Slicer! The Food Pusher is designed
so that it will not touch the Blades as
you slide it up and down the face of the
Slicer.
NOTE: A small at edge may need
to be sliced on the top of the food so
there is a stable area for the Food
Pusher to hold on to.
8. To adjust the thickness of the slices,
pull out and turn the Depth Adjustment
Knob and turn it clockwise. This will
lower the Depth Plate, making thicker
slices. Turning the Depth Adjustment
Knob counter-clockwise will raise the
Depth Plate, making thinner slices
FIGURE F
9. Hold onto the handle on the Rear
Stand and using the Food Pusher with
the food attached. Slide the Food
Pusher downward to slice.
FIGURE F & G
10. Maintain constant pressure so that
the spikes of the Food Pusher continue
to hold the vegetable/fruit.
11. As an alternative, fold the Rear
Stand up and place the Slicer on top of
a bowl. Be certain that the bowl edges
align with the notches on the Slicer,
both front and back, so that the Slicer
remains stable while slicing. FIGURE H
12. For julienne slicing, pull out and
turn the Julienne Blade Knob to expose
either the 1/4” (0.64 cm) or the 3/8”
(0.375 cm) Julienne Blades. FIGURE I
FIGURE G
FIGURE E
FIGURE H
FIGURE I
Spikes
Rear Stand
Rear Stand
Handle
FIGURE F
Depth
Plate
Depth
Adjustment Knob
Notches
on Slicer
Julienne
Blade Knob
Julienne
Blades
Food
Pusher
7
ENGLISH INSTRUCTIONS
CLEANING INSTRUCTIONS
Clean the Mandoline Slicer immediately
after use to prevent food from drying on
the parts. Wash the Mandoline Slicer
Base and the Food Pusher by hand in hot
soapy water, rinse with clean water, then
dry immediately.
The Blades and the Food Pusher can be
washed in the top rack of a dishwasher.
Carefully position these pieces where they
won’t cut or damage other utensils.
1. When nished slicing, remove any
remaining food debris from the Food
Pusher and all Blades with a brush.
CAUTION! KEEP FINGERS CLEAR of
the Blade at all times. NEVER remove
debris from the Blade with your hands
2. Pull out and turn the Depth Adjustment Knob counter-clockwise to raise the
Depth Plate completely up.
3. Pull out and turn the Julienne Blade Knob to lower the Julienne Blades to the
position under the Slicer Base.
4. Remove the Slicing Blade pulling up and out on the Blade from the thumb slot.
Grasp only the plastic portion of the Blade.
CAUTION: Once the Blades are removed, DO NOT immerse them in water!
Blades should be washed either in a top rack of the dishwasher or by holding onto
the plastic portion of the Blade. With a soapy towel, wipe AWAY from the Blade
edges. To rinse Blade, hold by the Handle and wipe with a clean, damp towel, or
hold under running water. Dry thoroughly.
4. Store the Blades in the accompanying Blade Box. Return the Slicer and all
parts to the original box. Store in a cool, dry area. BE SURE TO STORE OUT OF
REACH OF CHILDREN!
Blade
Thumbslot
Depth
Adjustment
Knob
Julienne
Blade
Knob
Julienne
Blades
Depth
Plate
WARNING
SHARP BLADES
KEEP FINGERS CLEAR OF BLADE AREA!
Protective/cut-resistant gloves recommended whenever
handling the Blades!
8
ENGLISH INSTRUCTIONS
TYPES OF SLICES
Julienne Blades
There are 2 Julienne Blade Sets, 1/4” (0.64
cm) (14 Blades) or 3/8” (0.375 cm) (10
Blades).The more teeth on the Blade result in
thinner sticks/slices. Fewer teeth on the Blade
result in thicker sticks/slices.
For julienne slicing, pull out and turn the
Julienne Blade Knob to expose either the
Julienne Blades. FIGURE J & K
Use the Julienne Blades in conjunction
with the Flat Slicer Blade.
• Cut the food in sections corresponding
to the desired length of the julienne
strips (approximately 3”-6”
(7.6 - 15.2 cm) long). Food Pusher Spikes.
To dice: Make a pass over the julienne & at
blade combination. Next, rotate the food 90
degrees and make a second pass over the
blade to complete the cut.
Flat Slicer Blade FIGURE L
This is the Slicer’s main Blade and features
a straight edge for basic slicing. The straight
edge is ideal for slicing a variety of foods from
carrots and cabbage to lemons and potatoes.
Wavy/Wafe Slicer Blade FIGURE M
The Wavy/Wafe Slicer Blade creates crinkle
and wafe cuts. A wavy cut requires only one
pass over the Blade.
For a wafe cut, adjust the height of the Depth
Adjustment Plate so that the slices are only
slightly thicker than the serrated edge of the
Wavy/Wafe Slicer Blade.
• Use the Food Pusher to make a pass over
the Wavy/Wafe Slicer Blade.
• Next, rotate the food 90
o
and make a
second pass over the Blade to complete the
cut.
Grater Blade FIGURE N
The Grater Blade is great for grating hard
cheeses, chocolate & ginger.
Fine & Coarse Shredder Blades
FIGURE O & P
The Fine & Coarse Shredder Blades are used
for shredding cheeses, fruits and vegetables.
FIGURE J
FIGURE K
FIGURE L
FIGURE M
FIGURE N
FIGURE O
FIGURE P
Julienne
Blade Knob
Julienne
Blades
10
ENGLISH INSTRUCTIONS
There are basic rules to follow when handling food.
They are COOK, SEPARATE, CLEAN, and CHILL.
COOK
It’s crucial to cook food to a safe internal temperature to destroy bacteria that is present.
The safety of hamburgers and other foods made with ground meat has been receiving a lot
of attention lately, and with good reason. When meat is ground, the bacteria present on the
surface is mixed throughout the ground mixture. If this ground meat is not cooked to at least
160
o
F to 165
o
F (71
o
C to 74
o
C), bacteria will not be destroyed and there’s a good chance you
will get sick.
Solid pieces of meat like steaks and chops don’t have dangerous bacteria like E. coli on the
inside, so they can be served more rare. Still, any beef cut should be cooked to an internal
temperature of at least 145
o
F (63
o
C) (medium rare). The safe temperature for poultry is 165
o
F
(75
o
C) and solid cuts of pork should be cooked to 145
o
F (63
o
C).
SEPARATE
Foods that will be eaten uncooked and foods that will be cooked before eating MUST
ALWAYS be separated. Cross-contamination occurs when raw meats or eggs come in
contact with foods that will be eaten uncooked. This is a major source of food poisoning.
Always double-wrap raw meats and place them on the lowest shelf in the refrigerator so
there is no way juices can drip onto fresh produce. Then use the raw meats within 1-2 days
of purchase, or freeze for longer storage. Defrost frozen meats in the refrigerator, not on the
counter.
When grilling or cooking raw meats or sh, make sure to place the cooked meat on a clean
platter. Don’t use the same platter you used to carry the food out to the grill. Wash the utensils
used in grilling after the food is turned for the last time on the grill, as well as spatulas and
spoons used for stir-frying or turning meat as it cooks.
Make sure to wash your hands after handling raw meats or raw eggs. Washing hands with
soap and water, or using a pre-moistened antibacterial towelette is absolutely necessary after
you have touched raw meat or raw eggs. Not washing hands and surfaces while cooking is a
major cause of cross-contamination.
CLEAN
Wash your hands and work surfaces frequently when you are cooking. Washing with soap
and warm water for at least 15 seconds, then dry with a paper towel.
CHILL
Chilling food is very important. The danger zone where bacteria multiply is between 40
o
F and
140
o
F (4
o
C and 6
o
C). Your refrigerator should be set to 40
o
F (4
o
C) or below; your freezer should
be 0
o
F (-17
o
C) or below. Simple rule: serve hot foods hot, cold foods cold. Use chang dishes
or hot plates to keep food hot while serving. Use ice water baths to keep cold foods cold. Never
let any food sit at room temperature for more than 2 hours - 1 hour if the ambient temperature
is 90
o
F (32
o
C) or above. When packing for a picnic, make sure the foods are already chilled
when they go into the insulated hamper. The hamper won’t chill food - it just keeps food cold
when properly packed with ice. Hot cooked foods should be placed in shallow containers and
immediately refrigerated so they cool rapidly. Make sure to cover foods after they are cool.
NOTE: Special considerations must be made when using venison or other wild game, since it
can become heavily contaminated during eld dressing. Venison is often held at temperatures
that could potentially allow bacteria to grow, such as when it is being transported. Refer to
the USDA Meat and Poultry Department for further questions or information on meat and
food safety.
FOOD SAFETY
Weston Brands LLC warrants to the ORIGINAL RETAIL PURCHASER of this product that if operated in accordance
with the printed instruction accompanying it, then for a period of 1 year from the date of purchase, the product shall be free
from defects in material and workmanship.
The Warranty Card, along with a copy of the original receipt, must be received by Weston Brands LLC within 30 days
from purchase date for the warranty to apply. Failure to send the completely lled out Warranty Card, along with a copy of
the original receipt, will void the warranty.
The product must be delivered to or shipped freight prepaid to Weston Brands LLC for warranty services, in either
its original packaging or similar packaging affording an equal degree of protection. Damage due to shipping is not the
responsibility of the company. Weston Brands LLC charges a $35.00 per hour bench charge. NOTE: No repairs will
be started without the authorization of the customer. The return shipping cost to the customer will be added to the repair
invoice.
Prior to returning the product for Warranty Repair, the product must be thoroughly cleaned and free from any food
particles or other debris. Failure of the purchaser to comply with this standard will result in the unit being returned without
repair. In some cases, a $50 cleaning surcharge may apply.
Weston Brands LLC will repair (or at its discretion, replace) the product free of charge, if in the judgment of the
company, it has been proven to be defective as to seller’s labor and material, within the warranty period.
New or rebuilt replacements for factory defective parts will be supplied for one (1) year from the date of purchase.
Replacement parts are warranted for the remainder of the original warranty period.
For non-warranty repairs, contact Weston Brands LLC’s Customer Service at 1-800-814-4895 M-F 8am-5pm ET
(outside of the United States 001-440-638-3131) to obtain a Return Merchandise Authorization Number (RMA Number).
Weston Brands LLC will refuse all returns that do not contain this number. DO NOT RETURN THE UNIT WITHOUT
PROPER AUTHORIZATION FROM WESTON BRANDS LLC.
LIMITATIONS: The warranty is void if the product is used for any purpose other than that for which it is designed.
The product must not have been previously altered, repaired, or serviced by anyone else other than Weston Brands
LLC. If applicable, the serial number must not have been altered or removed. The product must not have been subjected
to accident in transit or while in the customer’s possession, misused, abused, or operated contrary to the instructions
contained in the instruction manual. This includes failure caused by neglect of reasonable and necessary maintenance,
improper line voltage and acts of nature. This warranty is not transferable and applies only to U.S. and Canadian sales.
Except to the extent prohibited by applicable law, no other warranties whether expressed or implied, including
warranty merchantability and tness for a particular purpose, shall apply to this product. Under no circumstances shall
Weston Brands LLC be liable for consequential damages sustained in connection with said product and Weston Brands
LLC neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than
such as is expressly set forth herein. Any applicable implied warranties are also limited to the one (1) year period of the
limited warranty.
This warranty covers only the product and its specic parts, not the food or other products processed in it. Weston is
not responsible for missing or damaged parts on discounted/clearance, resale or nal sale items where the seller may not
be able to guarantee full functionality or completeness of the unit.
CUT ALONG THE DOTTED LINE AND SEND THE WARRANTY CARD ALONG WITH A COPY OF YOUR
ORIGINAL PURCHASE RECEIPT TO:
Weston Brands LLC / WARRANTY
20365 Progress Drive, Strongsville, OH 44149 USA
Customer Name:
Address:
City/State/Zip/Country:
Telephone Number:
E-Mail Address:
Original Date of Purchase:
Product Model #:
Serial # (if applicable):
I have read the warranty information. Initial here:
WESTON WARRANTY INFORMATION
SAVE THIS WARRANTY INFORMATION FOR YOUR RECORDS!
WESTON WARRANTY CARD
SEND THIS CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT TO:
WESTON BRANDS LLC / WARRANTY, 20365 PROGRESS DRIVE, STRONGSVILLE, OH 44149 USA
Copy of Receipt
Included
15
INSTRUCCIONES EN ESPAÑOLINSTRUCCIONES EN ESPAÑOL
LISTA DE COMPONENTES
NÚMERO DE DIAGRAMA DESCRIPCIÓN DE LA PIEZA NÚMERO DE PIEZA
1 CUERPO DEL REBANADOR N/A
2 TAPA PROTECTORA DE LA HOJA N/A
3 HOJAS Y CAJA PARA HOJA (3B) 16-0503
HOJA RALLADOR CURSO
HOJA RALLADOR FINO
HOJA RALLADOR MEDIO
HOJA REBANADORA PLANA
HOJA REBANADORA ONDULADA/REJILLA
4 EMPUJADOR DE ALIMENTOS N/A
Si cualquier componente de esta unidad está roto, si no funciona debidamente, o si necesita un
instructivo de repuesto, visítenos en la Web en
WestonProducts.com
O llame a Weston Brands LLC larga distancia sin costo 1-800-814-4895
De lunes a viernes, de 8:00 am a 5:00 pm tiempo del ET. Fuera de Estados Unidos llame
al 001-440-638-3131
Ajuste de
profundidad
Soporte
posterior
Vista
inferior del
accesorio
de empuje
1
4
Clavos
Perilla Juliana
Navaja párrafo
Cuchilla
ralladora
(7mm)
Cuchilla de
rallado no
(2.5mm)
Cuchilla de
rallado grueso
(6mm)
Cuchilla
rebanadora
plana
Hoja
rebanadora
ondulada
Navaja
para
julianas
2
(Debajo)
3
Variedad de hojas,
se muestran a
continuación
Placa de
profundidad
3B
INSTRUCTIONS EN FRANÇAIS
25
DESCRIPTION DE LA PIÈCE
NUMÉRO DE SCHÉMA DESCRIPTION DE LA PIÉCE NUMÉRO DE LA PIÉCE
1 CORPS DE LA TRANCHEUSE N/A
2 COUVERCLE DE LAMES N/A
3 LAMES ET ÉTUI À LAMES (3B) 16-0503
BIEN SÛR RÂPE LAME
AMENDE LAME DE RÂPE
LAME DE RÂPE MOYENNE
LAME DE COUPE PLATE
LAME À COUPE ONDULÉE/GAUFRÉE
4 POUSSOIR N/A
N’hésitez pas à visiter notre site Web WestonProduct.com/support si un composant est cassé, l’outil
fonctionne mal, ou pour commander un nouveau mode d’emploi.
WestonProducts.com
Veuillez appeler Weston Brands, LLC au numéro sans frais : 1-800-814-4895
Du lundi au vendredi: de 8h00 à 17h00 ET. En dehors des États-Unis, veuillez
appeler le 001-440-638-3131
Bouton de
réglage d’épaisseur
Support
arrière
Vue
inférieure
du
poussoir
1
4
Aiguilles
Bouton des
lames pour
julienne
RÂPE
(7mm)
Lame pour
râper finement
(2.5mm)
Lame
pour râper
grossiére-
ment (6mm)
Lame de
coupe
plate
Lame à
coupe
ondulée
2
(Dessous)
3
Assortiment de
lames illustré
ci-dessous
Plateau
de réglage
d’épaisseur
3B
ATTENTION!
PLEASE INSPECT THIS PACKAGE THOROUGHLY FOR MISSING PARTS OR ANY PRODUCT DAMAGE.
IF YOUR PRODUCT CONTAINS SHIPPING DAMAGE, PLEASE CONTACT RETAILER FOR ASSISTANCE.
For all other questions regarding product usage, missing parts, product damage, difculty or warranty activation,
please contact the Weston Products Customer Service Team:
8:00 am to 5:00 pm ET, Monday thru Friday
U.S. Residents Customer Service Line: 1-800-814-4895 (Outside U.S. Call: 001-440-638-3131)
Weston Products LLC, 20365 Progress Drive, Strongsville, Ohio 44149
WestonProducts.com
Please DO NOT return this item to the retailer before contacting
Weston Products Customer Service.
SAVE THESE INSTRUCTIONS!
Refer to them often and use them to instruct others.
ATTENTION!
VEUILLEZ INSPECTER CET EMBALLAGE AVEC SOIN POUR Y DÉTECTER
TOUTE PIÈCE MANQUANTE OU ENDOMMAGÉE.
SI DES PIÈCES ONT ÉTÉ ENDOMMAGÉES PENDANT LE TRANSPORT, VEUILLEZ
COMMUNIQUER AVEC LE DÉTAILLANT POUR OBTENIR DE L’AIDE.
Pour toutes les autres questions concernant l’utilisation du produit, les pièces manquantes, les problèmes ou
l’activation de la garantie, veuillez communiquer avec l’équipe du service clientèle des produits Weston:
de 8:00 à 17:00 HNE, du lundi au vendredi.
Numéro de téléphone du service clientèle pour les résidents des É.-U. : 1-440-638-3131
Numéro de téléphone à l’extérieur des É.-U. : 001-440-638-3131 Weston Products LLC,
20365 Progress Drive, Strongsville, Ohio 44149
WestonProducts.com
Veuillez communiquer avec le service clientèle des produits Weston AVANT de retourner cet appareil au détaillant.
CONSERVER CES DIRECTIVES!
Veuillez les consulter fréquemment et les utiliser pour la formation.
¡ATENCIÓN!
Revise completamente el envase y compruebe que no falten partes o que algún producto esté dañado.
si el producto está dañado por el transporte, solicite asistencia al distribuidor.
Para todas aquellas preguntas referentes al uso del producto, partes faltantes, daño del producto, dicultad
o activación de la garantía, comuníquese con el equipo de servicio al cliente de weston products:
desde las 8:00 am hasta las 5:00 pm ET, de lunes a viernes
Línea de Servicio al Cliente para Residentes de EE.UU.: 1.800.814.4895 (Fuera de EE.UU., llame al: 001-
1-440-638-3131) Weston Products LLC, 20365 Progress Drive, Strongsville, Ohio 44149
WestonProducts.com
NO devuelva este artículo al vendedor minorista antes de comunicarse con Servicio al Cliente de Weston
Products.
¡GUARDE ESTAS INSTRUCCIONES!
Consulte estas instrucciones y úselas para enseñar sobre el uso de este producto a otras personas.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Weston 16-0501-W User guide

Category
Slicers
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages