Kenmore 385.19365 User manual

SEWmNG MACHINE

Owner's Manual

NIAQUINA DE COSER

Manual de lnstrucciones

f

MACHINE A COUDRE

Manuel d'instructions

Model, Modelo, Modele 385.19365 __o

#842-800-208 SEARS CANADA INC,, TRONT_ ONT., M5B 2B8 www.searscorn

ilVIPORTANT SAFETY iNSTRUCTIONS

Your sewing machine is designed and constructed only for HOUSEHOLD use°

Read all instructions before using this sewing machine,,

DAN G E R -- To reduce the risk of electric shock:

1, This sewing machine should never be left unattended when plugged inoAlways unplug this sewing machine from the

electric outlet immediately after using and before cleaning,

2. Always unplug before replacing a sewing machine bulb, Replace bulb with same type rated 3 Watts.,

3. Do not reach for a sewing machine that has fallen into water. Unplug immediately,,

4, Do not place or store this sewing machine where it can fall or be pulled into a tub or sink,. Do not place or drop it into water

or other liquid.

WARNJNG- To reduce the risk of burns, fire, electric shock, or injury to persons:

1 Do not allow this sewing machine to be used as a toy..Close attention is necessary when this sewing machine is used by

or near children.

2. Use this sewing machine only for its intended use as described in this owneCs manual.

Use only attachments recommended by the manufacturer as contained in this owner's manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped

or damaged, or dropped into water.

Return this sewing machine to the nearest Sears store or service center for examination, repair, electrical or mechanical

adjustment,.

4. Never operate this sewing machine with any air opening blocked. Keep ventilation openings of this sewing machine and

foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8° To disconnect, turn all controls to the off ("0") position, then remove plug from out_et.

9. Do not unplug by pulling on cord.To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.

t 1_Always use the proper needle plate..The wrong plate can cause the needle to break.

12. Do not use bent needles

13. Do not pull or push fabric while stitching. It may deflect the needEecausing it to break.

'14.Switch this sewing machine off ("O") when making any adjustment in the needle area, such as threading the needle,

changing the needle, threading the bobbin or changing the presser foot, and the like.

15 Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making any

other adjustments mentioned in this owner's manual

SAVE THESE INSTRUCT ONS

When using your sewing machine for the first few times, place a waste fabric under the presser foot and run

the machine without thread for a few minutes. Wipe away any oil which may appear,

]

Page is loading ...

WARRANTY

FULL 25 YEAR WARRANTY ON DEFECT IN MATERIAL OR WORKMANSHIP

For 25 years from the date of purchase, Sears will, free of charge, repair defects in material or workmanship which

appear in the internal mechanical part of the sewing machine.

FULLTWO YEAR WARRANTY ON ELECTRICAL EQUIPMENT OF SEWING MACHINE

For two years from the date of purchase, Sears will, free of charge, repair defects in material or workmanship which

appear in the electrical and electronic equipment of the sewing machine, including motor, wiring, electronic components,

switch and speed control.

FULL 90-DAY WARRANTY ON ALL PARTS AND MECHANICAL ADJUSTMENTS

For 90 days from the date of purchase, Sears will, free of charge, replace any parts and provide mechanical service

necessary for proper operation of the sewing machine, except for normal maintenance. Warranty service is available by

returning the sewing machine to the nearest Sears Service Center in the United States.

IFTHIS MACHINE IS USED FOR COMMERCIAL OR RENTAL PURPOSES, THE ABOVE WARRANTY

COVERAGES APPLY FOR ONLY 90 DAYS FROMTHE DATE OF PURCHASE

This warranty gives you specific legal rights, and you may also have other rights which vary from province to province

SEARS CANADA INC._ TORONTO, ONT., M5B 2B8

GARANTIA

GARANTIA COMPLETA POR 25 AI_IOS EN LA CABEZA DE LA MAQUINA DE COSER

Durante 25 afios desde la fecha de la cornpra, Sears ofrece, libre de costo, reparar los defectos en material o de manufactura que

puedan presentarse en los componentes rnec_nicos de la eabeza de la rn_quina de coser

GARANTIA COMPLETA POR 2 ANOS EN EQUIPO ELECTRICO DE LA MAQUINA DE COSER

Durante 2 aSos desde ta fecha de la compra, Sears ofrece, libre de costo, reparar los defectos en material o de rnanufactura que

puedan presentarse en el equipo el_ctrico de la m_quina de coser, incluyendo componentes el_ctricos, motor, conexiones el_ctricas,

interruptor y control de velocidad

GARANTIA COMPLETA POR 90 DIAS SOBRE TODAS LAS PARTES Y AJUSTES MECANICOS

Durante g0 dias desde ta fecha de ta compra, Sears ofrece, libre de costo, reernptazar cuatquiera parte y proveer el servicio rnecanico

necesario para ta apropiada operaci6n de la maquina de coser, excepto para mantenirniento normal.. Et servicio de garantia se puede

obtener enviando la rn&quina de coser al centro/departamento de Servicios Sears rnas cercano en los Estados Unidos..

SI ESTA M._QUINA DE COSER SE UTIL!ZA PARA PROPOStTOS COMERCIALES O DE ALQUILER, LA COBERTURA DE

GARANTI._ CtTADA M_,S ARRIBA ES V.&.LIDA UNICAMENTE DURANTE 90 DI'AS A PARTIR DE LA FECHA DE COMPRA

Esta garanti& le da a usted derechos legales especificos, pero usted puede tener tambi_n otros derechos los cuales var[an de

provincia a provincia

SEARS CANADA INC., TORONTO, ONT., M5B 2B8

GARANTIE

GARANTIETOTALE DE 25 ANS SUR LE MI_CANISME DE LA MACHINE

Pendant 25 ans,& partir de la date d'aehat, Sears r_parera gratuitement tout d6faut de mat_riau ou de fabrication qui apparaitra dans

te mecanisme de votre machine

GARANTIE TOTALE DE DEUX ANS SUR L'EQUIPEMENT I_LECTRIQUE

Pendant deux ans,& partir de la date d'achat, Sears reparera gratuitement tout d_faut de materiau ou de fabrication qui apparaitra

dans le rnoteur, le c&blage, I'interrupteur ou la comrnande de vitesse de marche, dans les circuits electriques ou _lectroniques.

GARANTIETOTALE DE 90 JOURS SURTOUTES LES PII_CES ET LA MISE AU POINT DU MECANtSME

Pendant 90 jours, a partir de la date d'achat, Sears effectuera gratuitement tout rernplacement de piece et r_glage n_cessaires

au bon fonctionnement de fa machine; l'entretien ordinaire _tant & lacharge de l'utilisateur. Pour b_n_ficier des avantages qu'offre la

garantie ci-dessus, adressez-vous a votre rnagasin habituet ou au service apr_s-vente Sears, partout aux Etats-Unis

SI CETTE MACHINE A COUDRE SERT A DES FINS COMMERCtALES OU DE LOCATION, LA GARANTIE Ct-DESSUS SE

LIMITE ._ 90 JOURS A COMPTER DE LA DATE D'ACHATo

Cette garantie vous donne des droits l_gaux precis, et _ventuellement d'autres droits, ceux-ci pouvant varlet d'une province & una

autre

SEARS CANADA 1NCo,TORONTO_ ONTo_1"7t5t32B8

IV

Machine Specifications

Item

Sewing speed (Maximum):

Stitch length:

Stitch width:

Stitch package (Stitch functions):

(Built-in stitches):

Buttonhole:

Machine dimensions:

Weight (Net):

ISpecification

820 r,p,m,

5 mm (Maximum)

7 mm (Maximum)

398

365

5 styles

W 410 mm (16,4") x D 180 mm (7 2") x H 295 mm (11 _8")

8,5kg (18,5 Ibs)

Especificaciones de la m_quina

Artfculo

Velocidad de costura (MAxima):

Longitud de puntada:

Ancho de puntada:

NLimero de puntadas (Funcionamiento de puntadas):

(Integradas):

Ojales:

Dimensiones de la mAquina:

Peso:

Especificaci6n

820 rp m

5 mm (MAxima)

7 mm (MAxima)

398

365

5 estilo

410 mm (!64") de ancho x 180 mm (72") de profundidad x 295 mm

(11 8") de altura

8 5kg (185 Ibs)

Caract_ristiques de la machine

Description

Vitesse de couture (Maximum):

Longueur du point:

Largeur du point:

Ensemble de points (points de couture):

(points integr_s):

Boutonniere:

Dimensions de la machine:

Poids de ta machine:

Caract_ristiques "_

820 points-minute

5 mm (Maximum)

7 mm (Maximum)

398

365

5 styles

Largeur: 410 mm (I64") x profondeur: 180 mm (72") x hauteur: 295 mm

(!18")

85kg (185 fb)

TABLE OF CONTENTS

SECTION I. NAMES OF PARTS

Cabinet and Tote bags .................................................................2

Names of Parts ...............................................................................2

Standard Accessories ..............................................................................4

Name of Parts ...................................................................................4

Available Accessories and Attachments ...........................................6

Extension Table ............................................................................8

o Detaching extension table ................................................... 8

o Free arm sewing ........................................................................8

• Attaching extension table .................................................................8

SECTION II. GETTING READY TO SEW

Connecting Machine to Power Supply .................................10

For Your Safety .........................................................................10

Operating Instructions ...........................................................................10

Electronic Sewing Speed Control ...........................................10

• Speed control lever ..................................................................... 10

• Foot control ..................................................................................10

Main Function of Buttons .........................................................12

Up/Down needle position button ......................................... 12

Auto-lock button ...........................................................................12

Reverse button ...........................................................................12

Screen sharpness adjusting dial ..............................................12

Language selection dia! .......................................................................12

Mode key ......................................................................................14

Stitch width selection ....................................................................14

Stitch length selection .................................................................'14

Edititng ...................................................................................................14

Elongation key .................................................................................14

Mirror image key ................................................................... 14

Message key ............................................................................................. 16

Twin needle ........................................................................... 16

Memory key ................................................................................16

Clear key ....................................................................................16

Stock/Call key ...............................................................................18

Direct pattern selection and number keys ........................... 18

o Direct pattern selection ....................................................... 18

° Number keys ..............................................................................18

Pattern Selection and Screen Indication ........................... 20

Number Key Selection ..............................................................20

Normal/Resumption Mode .............................................................22

Buzzer ..................................................................................... 22

To Raise or Drop the Feed Dogs ...................................................24

Pressure Adjusting Lever ...................................................... 24

Presser Foot Lifter ..............................................................................24

Changing Needle ......................................................................26

To Remove and Attach the Presser Foot ........................... 26

To Remove and Attach the Foot Holder ........................................ 26

Selecting Needle and Fabric ................................................. 28

Winding the Bobbin ...........................................................32-36

o Removing the bobbin ......................................................... 32

oSetting up the bobbin winding ............................................. 32

° To use the additional spool pin ......................................... 32

° Setting up the spool ........................................................... 34

, Winding the bobbin ...................................................................34

o Inserting the bobbin ....................................................... 36

Threading the Machine .................................................................... 38

- Threading the machine ...............................................................38

o Needle threader .........................................................................40

Drawing up the Bobbin Thread ...............................................42

Balanced thread tension .................................................................44

• Auto-thread tension ................................................................44

o Balanced thread tension ...................................................................44

• Manual thread tension adjustment ......................................44

SECTION liB. BASIC SEWING

Straight Stitch Sewing ..................................................................46

oStarting to sew ...............................................................................46

° Changing sewing direction .........................................................46

• Finishing sewing ................................................................. 46

Using the Seam Guide on the Needle Plate ...........................48

Turning Square Corners .......................................................................48

Using the Quilting Guide ....................................................... 48

Sewlng on Heavy Fabrics ..............................................................48

Manual Stitch Length ...................................................................50

Variable Needle Position ....................................................... 50

Various Utility Stitches ................................................................52

Basting .................................................................................................52

o Attaching the Embroidery foot .................................................52

° Starting to sew ...................................................................................52

Automatic Reverse Stitch ...........................................................54

Triple Stretch Stitch .......................................................................54

Stretch Stitch ................................................................................... 54

Auto-Lock Stitch ..............................................................................56

Saddle Stitch ........................................................................................ 56

Zigzag Stitches .................................................................................56

, To change the width and length ........................................ 56

Variation of Zigzag Stitches ............................................................. 58

Overcasting Stitch ............................................................................58

Tricot Stitch ........................................................................... 58

Knit Stitch ...............................................................................................60

Overedge sewing I ...................................................................60

Overedge sewing II .................................................................. 62

Overedge sewing III ..................................................................... 62

Sewing Button ....................................................................................64

Automatic Buttonh01e(BH 1) .....................................................66-70

=Sewing preparation ..............................................................66-68

oStarting to sew ..................................................................68-.70

Adjusting the Stitch Width and Density in Buttonholes .....70

oTo change the stitch width .................................................... 70

oTo change the stitch density ................................................ 70

Automatic Buttonhole(BH2/BH3) ................................................72

oBH2 sewing steps .....................................................................72

oBH3 sewing steps .................................................................. 72

Adjustingthe StitchWidth and Density in Buttonholes 2 and 3 ...72

• To change the stitch density .....................................................72

oAdjustment of the stitch width on buttonhole 2 .................72

oAdjustment of the stitch width on buttonhole 3 ..................72

Corded Buttonhole .....................................................................74

Zipper Sewing ................................................................ 76-78

oAttaching the zipper foot ........................................................ 76

oFabric preparation ................................................................ 76

Vl

•Startingtosew..............................................................76~78

DarningStitch....................................................................................80

oStartingtosew..................................................................................80

• For darning less than 3/4" (2 cm) ...........................................80

• To adjust the shape of darning stitch ......................................80

•To memorize darning stitch .....................................................80

Barracking ............................................................................... 82

oMemorizing bartacking ...................................................................82

. Adjusting the evenness of barracking ....................................82

Blind Hem ........................................................................................84

- Starting to sew ..............................................................................84

Pintucking .....................................................................................86

Quilting ...........................................................................................86

Shell Tack ........................................................................................88

Applique ...........................................................................................88

SECTION IV, DECORATIVE STITCHING

Smocking ....................................................................................90

Fagoting ..........................................................................................90

Scallop Stitch(A) ..........................................................................92

oStarting to sew ............................................................................92

Scallop Stitch(B) ..............................................................................92

° Starting to sew ............................................................................92

Patchwork .....................................................................................94

Satin Stitch .......................................................................................94

Cross Stitch .....................................................................................96

Decorative Stitch .........................................................................96

Twin Needle Stitch .....................................................................98

° Starting to sew ...............................................................................98

Adjusting Pattern Balance ........................................................100

Adjusting Distorted Stretch Stitch Patterns .........................100

AdjustingDistortedLettersorNumbersinRedor GreenMode .... 100

Programming Decorative Stitch Patterns .............................102

Cycle Stitching with Mirror Image Patterns .........................104

Restarting Programmed Patterns ............................................104

Elongation ........................................................................................106

One Point Stitch .........................................................................108

Sewing Letters in Block Style ...................................................110

Sewing Letters in Script Style ...............................................1t2

Editing Function I ...........................................................................114

Deleting a Stitch Pattern, Letter or Number by Editing ....114

Adding Letters or Spaces between Letters .........................116

Editing Function II ..................................................................116

SECTION V, CARE OF YOUR MACHINE

Clean the Hook Race and Feed Dogs ...................................118

Assemble the Hook Race ..................................................... 118

Removing the Light Bulb ...................................................... 120

Attaching the Light Bulb ............................................................120

VII

Page is loading ...

SECTION i. NAMES OF PARTS

Cabinet and Tote bags

A full line of sewing machine cabinets and Tote bags are

available through the RSOS catalog at your nearest Sears

retail store,

Names of Parts

O Extension table (Accessory box)

(_ Needle plate

(_ Needle threader

@ Thread cutter

O Face cover plate

(_DThread take-up lever

O Upper thread guide

(_ Top thread tension control

O Spool pin

@ Large spool holder

O Flip top stitch chart

@ Screen sharpness adjusting dia!

@ Liquid crystal display

@ Function touchpad

@ Electronic sewing speed control lever

Up/Down needle position button

@ Auto-lock button

@ Reverse stitch button

@ Feed balancing dial

@ Hook cover plate release button

@ Hook cover plate

@ Foot holder

@ Presser foot

@ Needle

2--@Needle clamp screw

Thumb screw

2@Machine sockets

@ Power switch

@ Handwheel

@ Bobbin winder stopper

@ Bobbin winder spindle

@ Carrying handle

@ Hole for additional spool pin

@ Presser foot lifter

@ Buttonhole lever

@ Free arm

@ Drop feed dog lever

@ Nomenclature plate

@ Power supply cord

@ Foot control

®

2

@ @

Page is loading ...

Standard Accessories

Names of Parts

(_ A: Zigzag foot

(_)C: Overedge foot

(_) E: Zipper foot

(_ F; Satin stitch foot

(_)G: Blind hem foot

(_)H: Straight stitch foot

O R: Automatic buttonhole foot

(_ M: Overcasting foot

(_)P: Embroidery foot

@ Bobbins

@ Large screw driver

@ Lint brush

@ Needle set

@ Seam ripper / buttonhole opener

@ Large spool holder

@ Small spool holder

@ Spool stand

@ Additional spool pin

@ Quilter

@ Twin needle

d'_Spool pin felt

@ Hard cover

@ Video cassette

* Large spool holder is attached on the thread spool pin.

1 2 3

5 6

9

8

11 12

13

4

10

14

15

16 17 t8

t9

\

21

22

Page is loading ...

Available Accessories and Attachments

All parts listed may be ordered from any Sears store or

service center,

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE

FOLLOWING INFORMATION:

1 PART NUMBER

2, PART DESCRIPTION

3, MODEL NUMBER

4. NAME OF ITEM (SEWING MACHINE)

If the parts you need are not stocked locally, your order wil!

be electronically transmitted to a Sears Repair Parts

Distribution Center for expedited handling.

For the repair or replacement parts you need delivered

directly to your home.

Call 6 am - '11pm, CST, 7 days a week.

1-800-366-PART (1-800-366-7278)

Ref. No

1

2

3

4

5

6

7

8

9

10

tl

t2

13

t4

t5

16

17

18

19

2O

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

4l

42

43

Part No.

i'!02869107

802422002

102403202

650807008i

*993001100!

"993011100i

"993011400i

"993011600

"993011800

625031500

832523007

822801001

829801002

822824118

820817015

823801015

822808008

753801004

654805008

802424004

822020503

822019509

829803004

647808009

820832005

"647803004

"741814003

*784805004

000009906

'2oo002008

*200003009

_20o005001

"20o077107

"20o0131o5

*200081104

*200080103

*200031109

"2ooo32!0o

*200030108

*200029104

"200028103

*200027102

*214872011

"942630000

-200o78108

"2oo079109

826815000

842801014

Description

10 x Bobbin

Quilter

Spool pin felt

Assorted needle set

5 x No 11 stretch fabric needle (BLUE)

x No 11 needle (ORANGE)

x No 14 needle (RED)

5 × No !6 needle (PURPLE)

5 x No18 needle (GREEN)

Additional spool pin

A:Zigzag foot

C:Overedge foot

iE:Zipper foot

F: Satin stitch foot

G:Blind hem foot

H:Straight stitch foot

M:Overcast foot

R:Automatic BH foot

Embroidery foot

Lint brush

Large spool holder

Small spool holder

Spool stand

Seam ripper / Buttonhole opener

Large screw driver

Small screw driver

Oil

Needle threader

Light bulb

Piping foot

Gathering foot

Pin-tuck foot

Deep groove pin4uck foot

Hemmer foot (2mm)

Hemmer foot set (4mm. 6mm)

Ribbon / Sequin foot

Applique foot

Cording foot

1/4" Seam foot

Ultraglide foot

Roller foot

Binder foot

Walking foot

Ruffler

FSn4uck cord guide

Circular sewing attachment

Twin needle

Video cassette

These items are not furnished with the machine, but may be ordered per

instructions above.

"1 2

_ 5 6 7

8

9 10 11

%%,%

13 14

%

17 18

"21_

*26

15

20

12

%

16

6

"31 *32 *33 "34

*35 "36 *37 "38j----._

//

Page is loading ...

Extension table

The extension table provides added sewing surface and

can be easily removed for free arm sewing.

o Detaching extension table

Pull the table away from the machine, as itlustrated_

Free arm sewing

Free arm sewing is useful for darning socks or mending

knees, etbows or areas of wear in children's clothe&

\

............. i

Attaching extension table

Push the extension table urlti! it snaps into the machine.

0 Projection

(_ Hole

Page is loading ...

SECTION ii. GETTING READY TO SEW

Connecting Machine to Power Supply

Before connecting the power cord, make sure the voltage

and frequency shown on the machine conform to your

electrical power,

* Turn off the power switch (_,. Insert the foot control plug

(_ and the machine plug (_, into the machine. Insert the

power supply ptug (_ into the wall in this order:

(_ Foot control plug

(_) Machine plug

(_ Power supply plug

(_ Power switch

(_) Power supply cord

(_ Foot control

For Your Safety

* While in operation, always keep your eyes on the

sewing area. Do not touch any moving parts such as the

thread take-up lever, handwheel or needle.

* Always turn off the power switch and unplug from the

power supply:

-- When leaving the machine unattended.

-- When attaching or removing parts.

-- When cleaning the machine..

* Do not place anything on the foot control when not

sewing

Operating Instructions

"For appliances with a polarized plug (one blade wider than

the other)

To reduce the risk of efectric shock, this plug is intended to

fit in a polarized ourlet only one way, tf it does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact

a qualified electrician to install the power outlet. Do not

modify the plug in any way"

"Foot Controller Model YC-542 for use with Sewing

Machine Model 385.19365XXX"

XXX - represents numbers 000 through 999,

,J

Electronic Sewing Speed Control

o Speed control lever

Sewing speed can be controlled by adjusting the speed

contro_ lever 1_,

To increase the maximum sewing speed, slide the lever

to the right

To decrease the maximum sewing speed, slide the lever

to the }eft.

(_ Speed setting lever

. Foot control

Sewing speed can be varied by the foot control

The harder you press on the foot control, the faster the

machine runs,

10

Page is loading ...

Main Function of Buttons

Up/Down needle position button

When the Up/Down needle position button is pressed,

the needle bar goes down and stops in the lowest

position. When pressed again, the needle bar goes up

and stops in the highest position°

* When this button is pressed, the needie bar

alternates up and down positions when the

machine stops.

_) Auto-lock button

1>

When stitches • _ -> are selected, the machine

will immediately sew locking stitches when the

auto-lock button is pressed, then automatically stop.

When sewing all other stitches, the machine will sew

locking stitches at the end of the current pattern and

automatically step.

(_ Reverse button

When stitches ¢_ _ :_ are selected, the machine

will sew in reverse while the reverse button is pressed,

if you press the reverse button when sewing all other

stitches, the machine will immediately sew locking

stitches and automaticaly stop,

®Screen sharpness adjusting dial

Use this to adjust the sharpness of the liquid crystal

display. If no indication is shown on the screen after

you switch on the power, adjust the screen brightness

with this dial.

(_ Language selection dial

Set the indication mark "A" to a dot" -" with the end of

the lint brush to select the language you need.

[] English

_] Spanish

[] French

12

I 1

® ®

® U

®

, 'I_A \/-7; ,

I

\v [] [] []

Page is loading ...

_Mode key

By pressing the key, the LED light moves step by step

to select the stitch mode, as shown.

[] Direct mode pattern selection

[] Blue mode pattern selection using number keys

(utility and decorative stitches)

[] Red mode character selection using number keys

(block type)

[] Green mode character selection using number

keys (script type)

® Stitch width selection

Press "+" or "-" to change the stitch width°

_)Stitch length selection

Press "+" or "-" to change the stitch tength_

@Editing

This button can be used for adding and changing

combinations and monograms before sewing while

programming stitch patterns or monograms.

For editing, use the stitch width "+" or '-" key to select

editing position (see page 114,116)o

Manual setting function of the zigzag width and stitch

length for programmed patterns.

The individual programmed zigzag pattern width or

stitch length can be changed (see page 56).

@Elongation key

(For Blue mode stitches)

Stitches 40 to 55 can be elongated up to five times

their normal length by pressing this key.

_Mirror image key

(For Blue mode stitches)

Select a desired pattern and press (_ (Mirror image

key) so the selected pattern's mirror image will be

shown on the screen.

Use this key to memorize and sew patterns in a mirror

image. Programmed letters or numbers will be

reduced to 2/3 of their actual size when you press the

mirror image key.

'!4

®

[] []

"_SDIRECT o DIRECT

o 01"-'99 '+:-01~99

o 01~67 o 01~67

o 01,-,67 o 01~67

_+.DIRECT

o 01-,99

o 01,-,67

o 01~67

[]

o DIRECT

o 0'1"-,99

"+:-01~67

o 01,'-'67

WIDTH

®

- +

®

LENGTH

®

@

[]

o DIRECT

o 01"-'99

o 01--,67

3:-01~67

Page is loading ...

@ Message key

When the message key is pressed, a detailed message

will display suitable stitches, patterns and

machine setting,.

@Twin needle

Press this button and "1_" mark will appear on the

display screen° Press button again for single needle

sewing.

@ Memory key

When this key is pressed after selecting a pattern, the

pattern will be memorized as many times as the key is

pressed,. When the key is pressed after selecting

another pattern, that pattern will be memorized after

the previously memorized pattern.

(The maximum number of memory patterns are 5&)

*The following patterns cannot be memorized.

clP cL

* The Direct mode patterns cannot be memorized.

@Clear key

if an incorrect pattern is memorized, pressing this key

will immediately clear it (like a backspace key).

@

' _ I i

. x%.., J

--> _ nUTO_n'_ 3.52._(

STRAIGHT STITC_

PRESSURE:3 d

ZIPPER SEWING

FOOT:E

_.2.5__RUTO F" 3.52.5J

MEM

@

16

Page is loading ...

@ Stock/Call key

When you press the Stock/Call key after memorizing a

pattern or editing patterns, the current registered

patterns witf be deleted and new patterns will be

stored° Other than this, you can recall the stored

patterns when you press the Stock/Call key°

You can store a maximum of 50 programmed patterns

per mode.

* You cannot store the Direct mode patterns. Also

you cannot memorize patterns by using the memory

key.,

Q Direct pattern selection and number keys

• Direct pattern selection

You can select the patterns 01 to 10, and buttonhole

stitches BH1 to BH3 when the mode key isset at the

direct selection.

In the Blue mode 01 _96, the patterns 0t to 10 can

be selected when you setect the numbers instead of

Direct mode..

° Number keys

Press Number key of the pattern number to select

the desired pattern.

@

$ 1 2 Ill

BH1 01 02 O3

BH2 04 O5 08

g i o

BH3 07 08 0S

0

IQ

18

Page is loading ...

Pattern Selection and Screen Indication

[]Select the Direct mode pattern selection.

_jPress the pattern key on the keyboard°

Example: Pattern 04, as shown,

[_The display screens shows from left to right:

(_ Stitch pattern: 04

(_ Thread tension: AUTO

® Presser foot: A

@ Stitch width: 5.0

(_) Stitch length: 2_0

(_ Buzzer sound I_

(See page 22 to delete the buzzer sound)

* The type of presser foot is selected for suitable sewing

on display screen° A different presser foot, for the same

stitch on various sewing techniques, may be indicated.

m

DIRECT

o 01~96

o 01_67

[]

I@°1

[]

_m

AUTO

Number Key Selection

You can select the patterns by pressing number keys.

Example: pattern number 46

o DIRECT

_+_01~96

0_

o 01 --_67

ol 9._2,2/ /

¢ x%- J

4-6 RUTO F_ 2.08,4•

20

Page is loading ...

Normal / Resumption Mode

Turn on the power switch while pressing the memory

key,

(_ Memory key

(_ Power switch

[] Select "1" (_ on the number key to access the Normal/

Resumption mode. You can select the mode by

pressing the stitch width key "+" or "-",,

* Normal mode

The last selected pattern setting will not be recalled

when restarting your machine. Direct mode is

shown when the machine is turned on.

* Resumption mode

The last selected pattern setting will always be

recalled when you restart your machine.

[] Select desired mode: NORMAL SET or RESUMPTION

SET

[] Press the Memory key.

Buzzer

[2] ]3Jrn on the power switch while pressing the memory

key,

Q Memory key

(_) Power switch

[] Select "2" @ on the number key to access the Buzzer

mode. You can select the mode by pressing the stitch

width key "+" or ",

[_ Select desired mode "-" SOUND ON or "+" SOUND

OFE

[] Press the Memory key,

(_ Buzzer sound setting mark

(_ NORMAL / RESUMPTION setting mark

[] -I 1I

RESUMPTION SET

®

SOUND OFF

$

h SOUNDON

22

Page is loading ...

To Raise or Drop the Feed Dogs

The drop feed dogs lever is located underneath the free

arm bed on the back side of the machine.

Q To drop the feed dogs, push the lever in the direction

of the arrow as illustrated°

® To raise the feed dogs, push the lever in the direction

of the arrow as illustrated and turn the handwheet

toward you°

Feed dogs must be up for normal sewing.

4==,

©

.==1,

®

)

Pressure Adjusting Lever

Q Pressure adjusting lever

The pressure adjusting lever should be set at "3" for

regular sewing. Reduce pressure to "2"for applique, cut

the work, draw work and basting°

Set pressure at "1" when sewing chiffon, lace, organdy and

other fine fabrics, Velour and knits with a lot of stretch may

also require pressure at "1"o

Presser Foot Lifter

O Presser foot lifter

@ Normal up position

_) Highest position

The presser foot lifter raises and lowers your presser foot,,

You can raise it about 1/4"(0.6ore)higher than the normal

up position for easy removal of the presser foot or help you

place heavy fabric under the foot.

24

Page is loading ...

Changing Needle

[_ Raise the needle by pressing the up/down needle

button and lower the presser foot,,

Turn off the power switch.,

Loosen the needle clamp screw by turning it

counterclockwise.

Remove the needle from the clamp.

[] Insert the new needle into the needle clamp with the flat

side to the rear.

When inserting the needle into the clamp, push it up as

far as it will go. Tighten the clamp screw firmly by

turning it clockwise.

[] To check for a good needle, put the flat side of the

needle onto something fiat (the needle plate, glass,

etc.). The gap between the needle and the flat surface

should be consistent° Never use a bent or blunt needle.

(_ Needle clamp screw

(_) Pin

® Needle clamp

[]

r/-7-7-7-// f / E /

k ...............................

To Remove and Attach the Presser Foot

[] Press the red button on the back of the foot holder,. The

presser foot wilt drop off,

[] Place the selected presser foot so the pin on the foot

lies just under the groove of the foot holder, Lower the

presser bar to lock the foot in place,

0 Red button

(_) Groove

® Pin

To Remove and Attach the Foot Holder

[] To Remove:

Remove the thumb screw by turning the screw counter-

clockwise with the screwdriver.

[] To Attach:

Match the hole in the foot holder with the threaded hole

in the presser bar,

Fit the thumb screw into the holeo

Tighten the screw by turning clockwise.

O Thumb screw

(_) Foot holder

® Presser bar

[]

,*.1%t

[]

@___/

[] []

®

26

Page is loading ...

Selecting Needle and Fabric

For general sewing use needle size 11 or 14. A fine thread and needle should be used for sewing lightweight

fabrics so the fabric will not be marred° Heavy fabrics require a needle large enough to pierce the fabric

without fraying the needle thread.

In the needles case there is one each of size 11, 14, 16, 18 and blue needieo Use a blue needle to eliminate

skipped stitches when sewing knits and synthetic fabrics°

Special needles should be used on certain fabrics. A denim needle with a sharp tip is used to effectively

pierce dense fabrics such as denim and canvas.. For topstitching, a special topstitching needle with a larger

eye accommodates heavier weight thread. Leather needles punch small holes in leather and suede allowing

the thread to follow through the hole.

Check your needles frequently for rough or blunt tips. Snags and runs in knits, fine silks and silk4ike fabrics

are permanent and are often caused by damaged needle&

Always purchase a good quality thread. It should be strong, smooth and consistent in thickness°

f

WEIGHT

Very Light

Light

Medium

Heavy

FABRIC

Chiffon, Georgette, Fine Lace,

Organdy, Organdy, Net, Tulle

Batiste, Voile, Lawn, Pure Silk,

Crepe de Chine, Sheer Crepe,

Chambray, Handkerchief Linen,

Gingham, Challis, Percale, Wool

Crepe, Peau de Soie, Taffeta, Satin,

Silk Surah, Satin-backed

Crepe, Qiana

Single Knits, Jersey, Swimwear,

Tricot

Leather, Suede

Flannel, Velour, Velvet, Muslin,

Velveteen, Poplin, Corduroy, Broad-

cloth, Linen, Chintz, Gabardine, Felt,

Terry, Burlap, Quilted Fabrics

Double Knits, (synthetic and natural)

Stretch

Velour,

Stretch Terry,

Sweater Knits

Leather, Vinyl, Suede

Denim, Sailcloth, Ticking

Double Faced Wool, Heavy Coating,

Fake Fur, Drapery Fabrics

Leather, Suede

Canvas, Duck, Upholstery Fabrics

Topstitching for Special Finish

Universal

Bail point

TYPE OF NEEDLE NEEDLE SIZE

9 (65)

Blue

Orange

Blue

Ball point

Wedge point leather

Red

Ball point

Wedge point leather

Denim

Purple

Wedge point leather

Green

Topstitching

11 (75)

12(80)

1! (75)

11 (75)

11(75)

14 (90)

14(90)

16 (100)

16(1oo)

i6(1oo)

18(11o)

1ii75)

14(90)

28

Page is loading ...

Kenmore 385.19365 User manual

This manual is also suitable for

Kenmore 385.19365 User manual

in other languages

Related papers

Other documents