Stell SHO 1050 Specification

1-EN

LCD WALL MOUNT

For Model:

SHO 1050

Universal Mounting Instructions

2-EN

Installation Instruction

UNPACKING INSTRUCTIONS

• Carefully open the carton, remove contents and lay out on cardboard or other

protective surface to avoid damage.

• Check package contents against the Supplied Parts List in the next page to assure that

all components were received undamaged. Do not use damaged or defective parts.

• Carefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

Install and operate this device with care. Please read this instruction before beginning

the installation, and carefully follow all instructions contained herein. Use proper safety

equipment during installation.

Please call a qualified installation contractor for help if you:

• If you don‘t understand these directions or have any doubts about the safety of the

installation.

• If you are uncertain about the nature of your wall, consult a qualified installation

contractor.

Do not use this product for any purpose or in any configuration not explicitly specified in

this instruction. We hereby disclaims any and all liability for injury or damage arising from

incorrect assembly, incorrect mounting, or incorrect use of this product.

Note: Specifications and the design are subject to possible modification without notice due

to improvement.

3-EN

IMPORTANT:

• Before installation and use, carefully read this guide and keep it for future use.

• When using electrical tools for tightening bolts, please pay increased attention.

• When tightening bolts make sure not to strip the thread. It could damage the video

table / holder. Don‘t install this product into a wet or otherwise damaged wall. Fastening

materials, which are supplied with the product are designed for installation on to walls

from massive wood, bricks or concrete. For assembly on to walls from other materials

consult an expert.

• Do not disassemble nor repair the product on your own.

• Never install or service this product if it shows signs of damage. If you are unsure,

contact your supplier. Stell takes no responsibility for the faulty installation of this

product.

• The product must be placed in such a way that the power socket is accessible after

installation.

• Sharp edges of this product may cause injury.

• This product is not designed to be handled nor installed by small children or

uninstructed persons, unless they are under the supervision of persons responsible for

ensuring safety during handling or installation of the product. Children should be under

supervision to ensure that they do not tamper with the product. Do not allow children

to hang on the product nor to handle it in any other way. If this is not the case, serious

injury may occur. Never insert fingers nor other items into the product‘s mechanism.

Persons could be injured or property damaged.

• Use this product in accordance with the user‘s manual and its intended application.

DISPOSAL OF USED ELECTRICAL & ELECTRONIC EQUIPMENT

The meaning of the symbol on the product, its accessory or packaging indicates

that this product shall not be treated as household waste. Please, dispose of

this equipment at your applicable collection point for the recycling of electrical

& electronic equipments waste. In the European Union and Other European

countries which there are separate collection systems for used electrical and

electronic product. By ensuring the correct disposal of this product, you will

help prevent potentially hazardous to the environment and to human health,

which could otherwise be caused by unsuitable waste handling of this product.

The recycling of materials will help conserve natural resources. Please do not

therefore dispose of your old electrical and electronic equipment with your

household waste. For more detailed information about recycling of this product,

please contact your local city office, your household waste disposal service or the

shop where you purchased the product.

Changes in text and technical parameters reserved.

INSTRUCTION FOR HANDLING WITH USED PACKAGING

Used packaging should be dumped on the place appointed for dumping of the waste,

or into the junk.

4-EN

Supplied Parts List

(1) Wall Plate-a (1) Left Monitor Bracket-b (1) Right Monitor Bracket-c (1) Allen Key-d

(4) M4x12 Bolt-e (4) M5x12 Bolt-f (4) M6x12 Bolt-g (4) M8x16 Bolt-h

(4) M4x30 Bolt-i (4) M5x30 Bolt-j (4) M6x35 Bolt-k (4) M8x40 Bolt-l

(4) M4 Lock Washer-m (4) M5 Lock Washer-n (4) M6 Lock Washer-o (4) M8 Lock Washer-p

(4) M4/M5 Space-q (4) M6/M8 Space-r (8) M4/M5 Washer-s (4) M6/M8 Washer-t

(6) M8x90 Lag Bolt-u (6) Lag Bolt Washer-v

(6) M10x80 Concrete

Anchor-w (2) Plastic Knob-x

Pls install the Plastic Knob (x) on the Monitor Bracket

(b, c) as left diagram before do the next step. Pls note

the two knobs should be installed in the opposite way

on the two monitor brackets.

5-EN

WARNING

CAUTION!

This TV mount must be securely attached to the vertical wall. If the

mount is not properly installed it may fall, resulting in possible injury

and/or damage.

Tools

Required:

 3/16“ (5 mm) Drill Bit

 Screwdriver

 2/5“ (10 mm) Masonry Bit

 Stud Finder

 Wrench or Socket Set

 Carpenter‘s Level

Note: The mounting components and hardware supplied in this package are not

designed for installations to walls with steel studs or to cinder block walls. If the

hardware you need for your installation is not included, please consult your local

hardware store for proper mounting hardware for the application.

Step 1A Mounting the Monitor Brackets to a TV with Flat Back

First of all, make sure the diameter of the Bolt(e,f,g,h) your TV requires. Once you have

determined the correct diameter, please see the relative diagram as below. You will thread

the Bolt into the TV using the correct Lock Washer(m,n,o,p) and Washer(s,t). Please make

sure the Monitor Brackets(b,c) are vertically centered and level with each other.

M4 Diameter Bolt M6 Diameter Bolt

Diagram 1A

M5 Diameter Bolt M8 Diameter Bolt

6-EN

Step 1B Mounting the Monitor Brackets to a TV with Curved Back

First of all, make sure the diameter of the Bolt(i,j,k,l) your TV requires. Once you have

determined the correct diameter, please see the relative diagram as below. You will thread

the Bolt into the TV using the correct Lock Washer(m,n,o,p), Washer(s,t) and spacer(q,r).

For the M4 or M5 diameter bolt, you will need another M4/M5 Washer between the Monitor

Bracket and the Spacer. Please make sure the Monitor Brackets are vertically centered

and level with each other.

Step 2 Mounting the Wall Plate to the Wall

Brick, Solid Concrete and Concrete Block mounting:

Use the Wall Plate(a) as a template to mark 6 hole locations on the wall. Three in the top

row of slots and three more in the bottom row. Make sure these holes are level and there

is at least 6“ (150 mm) distance between any two holes. Pre-Drill these holes with a 2/5“

( 10 mm) masonry bit to at least 3“ (75 mm) in depth. Insert a Concrete Anchor(w) into

each of these holes. Make sure the anchor is seated completely flush with the concrete

surface even if there is a layer of drywall or other material in front. Attach the Wall Plate to

the wall using 6pcs Lag Bolts(u) and 6pcs Lag Bolt Washers(v), shown in Diagram 2A.

M4 Diameter Bolt M6 Diameter Bolt

Diagram 1B

M5 Diameter Bolt M8 Diameter Bolt

7-EN

Wood Stud mounting:

The Wall Plate(a) must be mounted to two wood studs at least 16“ (406 mm) apart.

Use a stud finder to locate two adjacent studs.

It is a good idea to verify where the studs are located with an awl or thin nail shown in

Diagram 2B. Pre-drill a 3“ (75 mm) deep hole at the desired height in each stud using

a 3/16“ (5 mm) drill bit. Make sure these holes are in the center area of the studs and level

with each other. Use the Wall Plate as a template to mark the location of the second hole

in each stud. Drill 3“ (75 mm) deep holes using the 3/16“ (5 mm) drill bit in the marked

locations. Attach the Wall Plate to the wall using the 4pcs Lag Bolts(u) and 4pcs Lag Bolt

Washers(v).

Diagram 2A Diagram 2B

Step 3 Attaching Monitor to Wall Plate and Adding the Safety Bolts

Warning: Some TVs may require two people to lift! We are not responsible for

personal injury or product damage.

First hook the Monitor Brackets(b,c) over the top of the wall Plate(a), then let the bottom

of the Monitor Brackets rotated to the bottom of the Wall Plate as shown in the Diagram

3A. Use the Allen Key(d) to tighten the bolts. Then the Monitor Bracket will sit behind the

bottom tab on the Wall Plate as shown in the Diagram 3B.

Diagram 3A Diagram 3B

Stud

Finder

16 inch

wall wall

safety bolt

8-EN

Step 4 Levelling Mount

You can re-level the mount after the mount has been installed on wall. Levelling is

achieved by rotating the front plate the TV sits on. First, remove the TV from mount.

Then slightly loosen the 5 screws using the Allen Key. Place level on top front of plate

as shown and level accordingly. Tighten the 5 screws, do not over tighten.

Adjust screws

to level

WARNING

Use two people to lift and position the TV onto the Wall Plate.

Thanks for choosing our products, enjoy the using!

Page is loading ...

Stell SHO 1050 Specification

Stell SHO 1050 Specification

in other languages

Related papers

Other documents